Fluid & Gas Flow Equipment
Used in ceiling installation for communications and power, hard-to-reach 90-degree bends under decks and below floors, ICE Inside Corner Elbow allows for multiple conduit runs which are to be installed in parallel without interference while accessing elbow’s cover. Providing smooth pulling surface for conductors to glide against, product enables for easy access when adding or removing cables... Read More
Featuring superior-quality compression seal, HelaGuard Conduit and Fittings are suitable for maximizing product reliability in manufacturing, machine building, shipping and chemical industries. Designed with galvanized, jacketed, liquid-tight metal core conduit for flexibility and crush resistance, units protect electrical wires from mechanical failure caused by vibration, impact and moisture... Read More
Viscous products for volumes of 0.1 to 20 ml
Efficiency in the production process
Pharmaceutical production lines are to a large extent automated. The prerequisite for a cost-efficient and effective filling line is a high application rate or a short cycle time. This is made possible by filling pumps which, on the one hand, enable the high speed in the filling process. And, on the... Read More
Available in NSF approved materials with NSF-51® and NSF-61® certifications, HydroMode™ push-to-connect fittings can be used with polyethylene and other flexible tubing. Having up to 145psi at 70°C pressure and Shore A 98 hardness rating, product comes in 5/32 in. to 1/2 in. sizes and black, blue, natural, red, yellow, green, and white colors. Unit's body and collet of fittings are... Read More
Designed for heating and passing DEF throughout SCR system on commercial vehicles, SCR Hoses use nylon core tubes for on-vehicle DEF transfer. Eliminating problems of condensation, coagulation and freezing of liquids inside hose, unit uses extruded sheath to lock-in heating elements and provides uniform heating for longer time. Hoses are available in 4mm and 5.5mm EPDM cores and 6mm nylon core... Read More
Available in 3/8 in. to 2 in. sizes with vacuum to 960 PSI pressure rating , Coaxial Valves can be operated up to 400°F temperature. Featuring low current consumption, compact size, product is tested in controlling of vacuums, liquid, gelatinous, abrasive and aggressive media. Product is used in port connections and housing materials.Read More
New FLR tubing to be displayed and featured at IFPE2017 in Parker Booth #S-8242
RAVENNA, Ohio, January 16, 2016 - The Parflex Division of Parker Hannifin Corporation, the global leader in motion and control technologies, is expanding its diesel fuel tubing offerings to include FLR tubing with SAE J2044 quick connect fittings. FLR tubing is a light-weight, diesel fuel tube that can be... Read More
Parker’s TOUGHJacket™ Hydraulic Hoses with Enhanced Jackets Offer 100-times More Abrasion Resistance than Comparable HosesJanuary 21, 2017
New hose family to be displayed and featured at IFPE2017 in Parker Booth #S-8242
RAVENNA, Ohio, January 16, 2016 - Parker Hannifin, the global leader in motion and control technologies, has expanded the Parflex hydraulic hose line with the introduction of a family of TOUGHJacket™ hydraulic hoses, designed to withstand the strains of large-scale, heavy-duty... Read More
To support our building owner, MEP, and contractor customers Hays Fluid Controls has released our initial Revit – Model - Drawing File Configurator for the 2519 Mesurflo® Y-Ball Automatic Balancing Valve where files are available for download within the product page. We invite you experience our new configurator.
Hays Fluid Controls, founded in 1865, is been committed to exceeding... Read More
Accuracy means that the valve will deliver the right flow at the right pressure at the right time, and then provide a leak-free stop to the flow within milliseconds. Superior reliability means it will do all that equally well throughout millions of cycles. Because it is pressure-balanced, the co-ax® valve operates very smoothly, very reliably and extremely fast. The control tube is controlled... Read More
Available in sizes ranging from 25 to 500 gallons, ATL Aqui-fer™ and Aqua-Flex® NSF Water Bladder Tanks are equipped with NSF-61. Products are simple to operate and include 1½ in. diameter fill neck assembly. Featuring rubberized fabric underliner to protect tank from abrasive surfaces, units come with secure tie-down system and sunshield to protect against UV rays. Products are designed... Read More
Custom design of bladder accumulator repair kits. Standard and non-standard sizes available as 1G, 2.5G, 5G, 10G, 11G, 12.5G, 15G, 16.5G, etc. Materials: Nitrile, Low Temp Nitrile, Hydrin, Viton, etc...
Our bladder accumulator and repair kits are equivalent replacement to most of the US brands on the markets such as Parker/Greer, Oil Air, Accumulators, Tobul, etc.
Reasontek... Read More
Perfect results for the hygienic filling of abrasive spice pastes
ViscoTec’s dosing pumps have already proven themselves in many areas of application, particularly when it comes to the reliable and permanent dosing and filling of abrasive materials. After a challenging endurance test for the food industry, their wear resistance has been confirmed once again.
High demands on... Read More
A full line of vacuum inlet traps and filter media for protecting vacuum pumps employed in research and production ALD (Atomic Layer Deposition) processes is available from MV Products of North Billerica, Massachusetts.
MV Vacuum Inlet Traps for ALD processes range from 4” to 16” dia. with port sizes from NW-25 to ISO-160 for protecting vacuum pumps in applications with vacuum flow... Read More
Being latex-free and Class VI compliant, Hemostasis Valve can be used in EtO and Gamma sterilization methods. Product has rotating male luer lock and female luer lock sideport and comes as Y-connector. Valves are made from tinted polycarbonate material and available in double and one-handed types.Read More
Constructed from PEEK thermoplastic-polymer seal cartridges, Pneumatic and Anchor Electric Piston Pump handles high-heat and chemically hazardous composition and viscosities. Featuring detachable foot valve and high-temp stuffing boxes, Pneumatic comes in Model 101 that produces lifts to 555ft., Model 102 maintains steady flows to 5 US gpm and Anchor comes in Model 101 that produces lifts to... Read More
Designed with motor, breaker plate screen pack, linear valve, melt pipe, control system, and optional display panel, EDI Polystream Motorized Valve Assembly provides human machine interfacing. Using closed loop controlling, product is able to maintain back pressure within limit. Designed to provide automatic warning when excess contaminant is build up, motorized valve assembly ensures coat... Read More
We have been the exclusive manufacturer for Dimple Magnetic Motor Oil Plugs for 6 years. We have been involved with new designs and applications to constantly improve this product line. www.drainplugsmagnets.com
Hawk Manufacturing, Inc.
220 Zimmer Rd.
Indian Land, SC 29707
Hydraulic slow closure sanitary ball valves have small flow resistance coefficient, high degree of automation, wide range of functions, stable and reliable performance. These features have been applied in all kinds of industries and fields. Its main applications include:
1. It can replace the functions of electric gate valve and sanitary check valve at the outlet of the water pump,... Read More
Replacement Fittings for Most Foreign Manufactured Equipment
Mentor, OH, December 27, 2016 – Malone Specialty Inc., a quality manufacturer of industrial hose and hose fittings for over 30 years, is now manufacturing and stocking standard Metric Flat Face Fittings.
Steve Malone, President of Malone Specialty Inc. stated, “For years we have been providing metric fittings and... Read More