New Fluid & Gas Flow Equipment Products

VSD Compressors target customers with smaller air demands.

Models GA18 and GA30 are 18 kw and 30 kw variable speed drive compressors with flow ranges of 40-114 cfm and 40-159 cfm, respectively. Units are available with integrated refrigerant air dryers, compressed air filters, and con-densate treatment systems. They offer sound level below 71 dB, which allows customer to install compressor at point of use eliminating need for separate compressor room.

Power End Upgrades act as plug-in for centrifugal pumps.

Power End Upgrades, suited for end suction centrifugal pumps, require no piping or foundation changes. Using existing casing volute, impeller, baseplate, and motor, bearing frame and seal back pull out assembly acts as plug-in without requiring modification of existing pump or hydraulics. Adapter system allows one Power Frame to fit hundreds of different pumps. C-Frame motor adapters (blue) are...

Water-Jet Pumps feature engines up to 425 hp.

Series NLB 350 are convertible units with quick-change fluid end that lets users operate at any of 5 pressures to meet various job requirements. Pressures range from 8,000-20,000 psi and flows range from 27-74 gpm. Series includes diesel and electric units in 350 and 425 hp. Pumps have hard-coated valves and plungers, and corrosion-resistant stainless steel parts to extend operating life.

Load-Sensing Valves offer CAN-Bus pilot control module.

Series M4 Load Sensing Valves, using electronic control units or on-board electronic interfaces with CAN controller, bring open- and closed-loop control options to mobile applications. Sandwich-plate design features up to 10 elements. Section pressure compensators provide individual, load-independent flow control. Units are high-pressure proof up to 5040/6048 psi. Max inlet flow is 53 and 40 gpm...

Axial Flow Check Valves for Pumps and Compressors

DFT® Inc. has provided a range of valve solutions for customers struggling with pump and compressor problems.

Spray Nozzles use compressed air or gas.

Series JPL Air Atomizing Spray Nozzles produce controlled liquid dispersion. Standard assembly consists of 7 components that fit together to produce spray pattern. JP Air Cap and JL Liquid Nozzle determine spray pattern and liquid/air flow rates. Nozzles and components are offered in 303 SS, 316 SS, and nickel-plated brass. Applications include humidification, cooling, air pollution control,...

Spray Nozzle has anti-clog design.

Machined from solid brass, stainless steel, or PVC in one-piece design, YS Series Twister(TM) Nozzle allows full cone spray at low pressures. Product is suited for blasting away residue in washing and rinsing tasks and may also be used in gas cooling, chemical processing, and humidification applications. With no internal vane to clog or wear out, unit provides increased flow rate when compared to...

Needle Valve suits oil and gas industry.

Model HN41 straight-through, bi-directional needle valve features soft seat, ensuring repetitive bubble-tight sealing in both standard and dirty process conditions. Unit meets requirements of NACE MR-01-75 and is equipped with DelrinÃ-® seat and stainless steel material. Valve is rated at 6000 psig at 200Ã-

Hydraulic Pumps offer displacement to 45.75 cu in.

Comprised of 8 basic pump sizes, Superior Performance (SP) pumps include shaft seal, valves, and servo control system. Select pumps can be installed in tandem configuration, enabling one electrical motor to drive both pumps. With noise level of 75 dB(A) for pumps up to 30.5 in.-³, products include 15.25, 21.66, and 30.5 in.-³ models in addition to largest (45.75 in.-³) model. Pumps with...

Cylinder Manifolds distribute high-purity gases.

Series 52 Modular Manifolds, based on Ã-¼ in. pipe size, reduce wetted surface area and lessen potential for gas contamination. Metal-to-metal, field-assembled joints allow leak-tight field assembly. Integral diaphragm valves at each station provide for leak-tight integrity and eliminate gas contamination. Models are available in brass, chrome-plated brass, and 316 stainless steel. Components...

Header has R15 insulation value.

Manufactured from two 1 Ã-½ in. thick plies of 1.5 E TimberStrandÃ-® LSL, TJ9 has rigid foam core and provides insulation value of R15. Suited for 2 x 6 walls in various depths, header allows for one-piece installation and is stocked in lengths of 17 ft to 6 in. Environmentally friendly TimberStrandÃ-® LSL is manufactured from aspen and yellow poplar in process that randomizes wood's...

Reduce Time to Market, Improve System Uptime with Dedicated Computing Medical Solutions

Embedded computing solutions from Dedicated Computing are designed to meet unique and specific requirements. As the preferred supplier to leading healthcare OEMs, the Dedicated Computing team of expert engineers gets your product out to the market faster while helping your company avoid costly validation and verification steps. Check out our video to learn more.