Binks ITW Industrial Finishing    Glendale Heights, IL 60139
May 20, 2005 Stainless steel 1-quart siphon feed cup and 3 pressure assist cups are designed to provide precise fluid pressure control with conventional spray guns. They incorporate air regulator, flare lip cup, and flattened bottom cup design. They also feature proprietary check valve and vent design as well as lid, yoke, and lever design. Interchangeable parts include stainless steel cups, lids, lid gaskets, fluid tube, and yokes.

Viking Pump Inc., A Unit Of IDEX Corp.    Cedar Falls, IA 50613 0008
May 19, 2005 Able to operate in either direction, pumps with suction lift capability can be mounted above liquid level in barges and tankers for loading/unloading or line stripping. For terminal operations, Internal Gear and Industrial Lobe pumps offer thrust control and adjustable rotor clearances. Gear pumps handle viscosities from 28–2,000,000 SSU with capacities up to 1,500 gpm. Lobe pumps, in bi-wing or multi-lobe designs, provide pressures to 400 psi and offer capacities to 1,000 gpm.

J. W. Winco, Inc.    New Berlin, WI 53151
May 19, 2005 Fill/Drain Plugs, available in various thread sizes, are made of aluminum and feature matte, shot-blasted finish with laser-engraved refill and drain symbols. Molded of NBR synthetic rubber, seal exhibits max heat resistance of 250°F. Radial undercut in mating face prevents seal from dropping out or protruding when plug is tightened. Plugs are available in metric pipe thread and BSPP parallel threads.

Norgren    Littleton, CO 80120
May 19, 2005 With operating temperature of 0–176°F, Series 98000 3/2-way Control Valves feature 8 mm orifice and operate without lubrication. Units are type tested to IEC 61508 and are certified to safety integrity level 4. Valves have metal housing for outdoor implementation and are CSA and FM approved. They are available with range of protection class solenoids, such as IP65, EEx me, EEX md, and NEMA 4.

SMC Corporation Of America    Indianapolis, IN 46226
May 19, 2005 Model ASR Pressure Valve consists of regulator with check valve and speed controller, while Model ASQ Flow Valve combines quick supply/exhaust valve and speed controller. Body and one-touch fitting allow 360° rotation. Fixed set pressure type and variable set pressure type are available. Both valves can cut air consumption by operating return stroke at minimized pressure, preventing jerky movement of working stroke and operation delay in return stroke.

Bosch Rexroth AG Industrial Hydraulics      Germany
May 19, 2005 Suited for demanding applications and control of working equipment, variable displacement axial piston pumps feature aluminum alloy casing and taper roller bearing used to accommodate thrust load. To accommodate radial load, products utilize CARB toroidal roller bearing type: C 2207 TN9/C3 lubricated by complete oil immersion. Bearing is self-aligning and accommodates misalignment between shaft and housing. Speed is rated to 2,500 rpm.

Flowserve Corporation    Irving, TX 75039
May 17, 2005 Flowserve Limitorque PT series provides torque needed for operation of quarter-turn valves. Models PT-12 and PT-14, rated at 880 and 1,600 lb-ft respectively, are constructed with cast-iron housing for weatherproof, submersible, or buried service applications. Optimized for motorized valve operation, products employ one-piece rolled worm and shaft and are available with ductile iron worm gears or bronze alloy worm gears for AWWA and modulating applications.

Walchem Corp.    Holliston, MA 01746 1460
May 17, 2005 Designed to operate in metering applications with variety of chemicals, EZB Series employs LCD for programming as well as digital control for adjustment and operation. Solenoid-driven diaphragm metering pumps offer output capacities to 3.2 gph and pressure capabilities to 150 psi. By pumping at 360 strokes/min, pumps minimize chemical slug feeding. They utilize fixed stroke length and sealed control panel, providing IP65 solution for harsh environments.

Fisnar Inc.    Wayne, NJ 07470
May 17, 2005 Model VC-1195A can control both ON and OFF action of 1 or 2 dispensing valves. By using air to open and close valve, unit maximizes valve suck-back action and minimizes material stringing problems.

Beswick Engineering Co., Inc.    Greenland, NH 03840
May 13, 2005 Measuring 18 mm in diameter, single-stage diaphragm Model PRDB-18MM-A-B-C is offered with 2 inlet and 2 outlet ports, allowing inlet and outlet lines to be connected in 4 different configurations. Regulator controls output pressures from 0–20 psig and is suited for low pressure regulation, even below 1 psig. Maximum rated inlet pressure is 300 psig. Four M3 tapped ports can be plugged with M3 screw plugs when not in use.

Knoll America, Inc.    Madison Heights, MI 48071
May 13, 2005 Compact, inline, Mahle Automatic Back-Flushing Filter handles volumes up to 175 gpm and filtration to 10 micron. Utilizing cyclonic chamber to separate solids from coolant prior to reaching filter, final filtration occurs when coolant is forced into center of filter and discharged. Backflushing of self-cleaning filter is initiated by fluid pressures as it is rotated by gear motor. Solid particle residue trapped in collecting cone is then drained into waste container.

Bio-Chem Valve, Inc.    Boonton, NJ 07005
May 13, 2005 Inert Solenoid Pumps and Valves are secured to manifold using locked-in threaded mounting collar, which is hand tightened to ensure even load on gasket seal for pressure up to 100 psi. By positioning pump or valve close to point of fluid introduction, screw-in manifold design minimizes internal volume. Valves can be customized in PEEK, PPS, Ultem, acrylic, Chemraz, EPDM, Viton, or Teflon® materials. Multiple manifold sizes can achieve flows from 10 µLpm to 2 Lpm.

Axcell (Heyco Products, Inc.)    Toms River, NJ 08755
May 13, 2005 Constructed from specially compounded infrared transmitting polycarbonate, Infrared Window Plugs are designed to permit transmission of electronic data into or out of electrical housing or enclosure. Offering high strength and chemical resistance, plugs are available in specific colors designed for visible light transmission and can be modified for openings that are oval, square, elliptical, or designed to custom specifications.

Duff-Norton    Charlotte, NC 28241 7010
May 12, 2005 Able to conduct water, hot oil, steam, chemicals, and air media, HPMC Series MultiPort Rotary Union accommodate 2–8 ports, each of which is individually sealed to eliminate crosstalk between channels. Device provides rotating seal between fluids and revolving roll or drum. Once clamped, slotted rotating disk remains in-place regardless of rotation. Operating parameters range up to 250°F, 5880 psi, and 180 rpm, and port sizes range from 1/8–1¼ in.

J. W. Winco, Inc.    New Berlin, WI 53151
May 12, 2005 Hexagon Socket Threaded Pipe Plugs are fashioned from zinc-plated steel with yellow passivated finish and are ultrasonically checked. With max heat resistance of 250°F, NBR synthetic rubber seal is retained in radial undercut in mating face, preventing it from dropping out or protruding when plug is tightened. Plugs are available in metric pipe thread and BSPP parallel threads.

Fisnar Inc.    Wayne, NJ 07470
May 12, 2005 High pressure dispensing valve, 790HPNM, dispenses dots and lines and performs potting applications with materials such as silicones, RTV, adhesives, greases, and UV curable materials. Retracting spool design ensures accurate deposit of material, and valve can be adapted for use on robotic or bench-top dispensing systems. Control is via company's standard controller or VC-1195A 4-way valve controller, which maximizes valve suck-back action and closes valve faster.

Dwyer Instruments, Inc.    Michigan City, IN 46361
May 12, 2005 Provided in 1/2-4 in. sizes, Series BV2 automated valve package offers ANSI 150 lb flanged ends to facilitate installation as well as blowout-proof stem, reinforced Teflon® seats and seals, and 316SS ball. Actuators are direct-mounted, creating compact assembly for tight spaces, while double O-ring stem seals ensure leak-free operation. Weatherproof electric actuated models are powered by 115 Vac supply and come with 2-position or proportional control.

Norgren    Littleton, CO 80120
May 12, 2005 Offered in over 45 different shapes, Pneufit D series push-in fittings are suitable for compressed air applications and approved by FDA, WRAS, SK Zert, and NSF-51 for use in food processing. Parts incorporate integral stainless steel grab rings, which offer secure assembly for Nylon PU and PE tubing. Tube sizes are available from 4–12 mm and 5/32–½ in. Pneufit D can also be specified with NPTF, BSP, and UN type threads.

Pfeiffer Vacuum Inc.    Nashua, NH 03063
May 12, 2005 Magnetic Root Pumps are statically sealed against atmosphere, eliminating rotating seals that wear and leak, as well as cross contamination and oil pollution. Ranging from 250-6,000 m³/hr, units are also hermetically sealed, resulting in negligible leak rate of less than 1 x 10^-5 mbar l/sec. Pumps are suited for chemical plant, coating, semiconductor, research and development, metallurgy, packaging, and freeze drying applications.

Dixon Valve & Coupling Co.    Chestertown, MD 21620 1135
May 12, 2005 Designed for transfer of hazardous materials, dry disconnect couplings facilitate connection and disconnection of hoses and pipelines while eliminating accidental spillage and product loss. They are available with stainless steel, aluminum, or brass construction in 1–4 in. sizes and feature built-in swivel. Design options include Hastelloy® C276 internal parts, Teflon® bushings, and Viton® seals. Couplings have working pressure of 260 psi or 360 psi.