Quadrant Valve & Actuator, LLC    Broussard, LA 70518
Mar 15, 2006 Seal-welded G3 Series is available in WCB carbon steel and CF8M stainless steel, both with standard 316SS trim and 304SS latch-lock handles. Standard construction is male NPT inlet with female NPT outlet, and all models have two ½ in. female NPT gauge ports on outlet side for gauge or instrument mounting. All wall thicknesses are per ASME B16.34, with inlet male NPT end per Schedule 80 pipe on ½-1 in. sizes and Schedule 160 pipe on 1½ and 2 in. sizes.

Lutz-JESCO America Corp.    Rochester, NY 14624
Mar 15, 2006 Featuring modular design, magnetic drive CENTRAN(TM) Centrifugal Pumps eliminate need for trimming impellers. Series TMB includes 5 models with flow from 3.96-18.49 gpm and heads from 7.8-35 ft. Built entirely of reinforced thermoplastic polymers, Series AM includes horizontal, close-coupled units with end suction centrifugals. Series G2 and G3 feature bi-directional, self-alignment systems, eliminating excess friction. All offer threaded and flanged connections.

D-Mark, Inc.    Chesterfield, MI 48051 2600
Mar 15, 2006 Self-supporting OdorGuard® Rigid Cell Filters remove odors, VOCs, and light gases. Units are available with granular activated carbon or 50/50 blend of carbon and activated alumina impregnated with 5% potassium permanganate. Filters are 24 x 24 x 12 in., pleated, and provide 7 lb of GAC or 8.6 lb of 50/50 adsorbent blend. Galvanized steel frames resist corrosion in moist, humid conditions, and are available with or without header.

Leybold Vacuum USA, Inc.    Export, PA 15632-8900
Mar 15, 2006 Offering environmentally friendly alternative to oil-sealed piston vacuum pumps, gas compression, screw-type Model SP250 is rated for 195 cfm and 7.5 x 10^-3 torr vacuum. Unit eliminates contaminated waste waters through air cooling and produces no emissions or back oil migration. Able to accommodate boosters directly, pump is suited for vacuum degassing applications in aerospace, automotive, drying, electrical, and leak testing applications.

Gardner Denver    Quincy, IL 62301
Mar 14, 2006 Providing up to 100 psi of pressure, Series 2665/2685 WOB-L® die-cast aluminum piston pumps incorporate epoxy coated head and valve plates for corrosion protection. Teflon® piston seal remains flexible in cold temperatures. Oil-less, non-lube piston and cylinders prevent air-flow contamination, and twin fans provide cooling of motor and cylinder. Series 2665 pumps are for use where fan guards are not required, and Series 2685 pumps include SS fan guards.

Air Options, Inc.    Houston, TX 77235-5984
Mar 14, 2006 With max operating pressure of 200 psi, Dry Doc, System, and Gang Series are available in sizes from 12-500, 600-3,000, and 4,000-15,000 scfm, respectively. Units maintain operating specifications with input temperatures up to 250°F and accept temperatures as high as 350°F with no damage. Constructed using welded SCH 40 piping components with type-122 copper alloy exchanger tubes, dryers utilize 2-stage water evaporation process that eliminates need for CFCs and desiccants.

TAH Industries, Inc.    Robbinsville, NJ 08691 1603
Mar 13, 2006 Targeted for low pressure spray applications, disposable plastic spray manifold can be used with conventional meter/mix equipment. Reactive coating is mixed within static mixer, then at mixer outlet, air is introduced which atomizes liquid stream. Effective for high viscosity liquids and abrasive suspensions, reactive coating is contained completely within disposable static mixer, minimizing clean up time.

Micro Plastics, Inc.    Flippin, AR 72634
Mar 13, 2006 Nylon Compression Nuts, Plugs, and Connectors are corrosion-resistant and have electrical insulating properties that virtually eliminate electrical action that could result in corrosion when dissimilar metal meets fitting. They absorb acoustic and mechanical vibration, extending useful life in many applications.

Blasch Precision Ceramics, Inc.    Albany, NY 12204
Mar 13, 2006 Nitron Parts include riser tubes and rotary degassers for molten aluminum, nozzles for copper and aluminum, and desulferization nozzles for coal burning power plants. Net shape forming process enables manufacture of complex ceramic shapes with varying wall thickness, and produces high dimensional accuracy, with tolerances better than ±0.5%, eliminating need for machining or finishing work. Because of micro-porosity, parts offer resistance to metal penetration.

Oilgear Co., The    Milwaukee, WI 53219 2340
Mar 13, 2006 Series PVK open loop, axial piston pumps are available in 3 displacements and in multiple frame sizes. Cylinder surface running on valve plate to provides resistance to contamination, and polymerous bearings on swashblock and saddle eliminate yoke bearings. Series features SAE keyed or splined shaft, sealed front shaft bearings to permit side loading, lubricated swashblock, and theoretical max displacements ranging from 8.61-22.4 in³/rev.

Jet Edge    St. Michael, MN 55376
Mar 10, 2006 Rated for 60,000 psi, 50 hp Model iP60-50 includes non-contact wet electronic stroke sensor that replaces contact actuator/proximity sensor combination. Piston/plunger design requires only one tool for maintenance, and intensifier assembly can be assembled with standard tools. Pump provides access for all service and maintenance and can be serviced in-house.

Bete Fog Nozzle Inc.    Greenfield, MA 01302
Mar 08, 2006 Twist and Dry(TM) Knife-edge Carrier tapers down from orifice to form sharp ridge at tip, eliminating flat face tip and minimizing buildup and associated hazards. Geometry makes it suited for use in co-current dryers and high fat content product applications. Carrier is compatible with standard Twist and Dry components, facilitating switch with no disruption in drying process.

Bosch Rexroth Corp., Pneumatics Div.    Lexington, KY 40511
Mar 07, 2006 Plug-in Model CD26-PL features 26 mm wide manifold with flows up to 1.01 C_v. In accordance with ISO standard 15407-2, simultaneous pneumatic and electrical connection is done on base plate. Manifold threaded ports are available in NPT and ISO-G. Valve offers single and double solenoid operation as well as double 3/2, allowing 2 functions from same valve position. Offered in multi-pin version with D-sub connector, valve can be combined with BDC, VDS, and DDL bus systems.

Schroeder Industries LLC    Leetsdale, PA 15056-1025
Mar 03, 2006 Taking dirt ingression rate and operating environment into consideration, Air Breather Check(TM) (ABC) test system notifies users when it is time to change air breathers. Tester is calibrated in inches of water and will activate, providing visual indication, when vacuum equivalent of 15 in. of water is reached. ABC can be reset by push of button and used repeatedly. Compact unit includes adapter with splash guard and is suited for various installations.

Parker Hannifin Corp., Tube Fittings Div.    Columbus, OH 43228
Mar 03, 2006 Suited for applications requiring high flow and low-to-medium system pressures, Seal-Lok(TM) Lite Fittings are adaptable to FlexFlange light-duty, flexible, corrugated stainless steel tube used in gas appliance industry. Captive O-ring groove seal provides leak-free connections while positively retaining O-ring. Fittings use existing stainless steel Parflange tooling and equipment and are adaptable to inch/metric tube, and tube and hose connections.

Posi-flate    Saint Paul, MN 55110 5128
Mar 03, 2006 Achieving up to 15 million maintenance-free cycles, Tork-Mate® 890 Series is suited for 90° and 180° turn devices such as butterfly valves, ball valves, plug valves, and damper valves. Units meet NAMUR standards, allowing direct or close coupling of NAMUR designed accessories. Custom options include Viton seals, high-temperature trim, special finishes, stainless steel pinions, and special mounting and coupling configurations.

KMC LaserForm Div. Of Kickhaefer Mfg. Co.    Port Washington, WI 53074
Mar 02, 2006 Cushion clamps series COL and CDL are available in hot-dipped galvanized steel, chemically treated G-90, or Type 304 annealed SS. Units are designed to secure and route wire, cable, tubing, and hoses. COL series offers contoured configuration clamping diameter, offset lower leg, and can secure one tube. CDL series can secure multiple tubes. Clamps are suited for agricultural, automotive, marine, OPE, recreational vehicle, and industrial manufacturing applications.

Spence Engineering Co., Inc.    Walden, NY 12586-0230
Mar 02, 2006 Accepting 3-15 lb air signal, pneumatically actuated Kombat K3 features 36 or 60 sq-in. actuator with spring-loaded packing assembly to minimize deadband. Kombat K7 features rapid-stroke, electric actuator that accepts 0-10 Vdc, 4-20 mA, or 0-135 Ohm signals. Both 3-way control valves have bronze ANSI 250 globe bodies with galvanized union ends and all stainless steel trim. Valves are suited for commercial, HVAC, and light industrial applications.

Alemite LLC    Fort Mill, SC 29715
Feb 28, 2006 Designed to operate at low temperatures without icing, Series 8600 is hydraulically powered, eliminating need for compressor and making it suited for automatic lubrication systems installed on mobile equipment where space is limited. Self-venting unit includes pressure and flow regulators as well as 24 Vdc control solenoid, which allows hydraulic fluid to power pump.

Trane    Cincinnati, OH 45215
Feb 23, 2006 Designed to deliver clean air throughout building, TRANE CleanEffects(TM) eliminates allergens and unwanted particles such as bacteria, pollen, mold spores, and pet dander down to .3 microns from filtered air. It electrically charges airborne particles, which are then pulled toward collection cells and removed from air. System offers typical clean air delivery rate of 1,200 cfm and has cleanable filter that never needs to be replaced.