FasTest, Inc.    Roseville, MN 55113-1317
Jun 20, 2013 Constructed of stainless steel and anodized aluminum, FasMate FN Series can withstand pressures up to 3,500 psi without thread sealant and wrench tightening. In addition to thread port sealing range of 1/8–½ in. NPT, BSPP, BSPT, SAE O-Ring, and ISO O-Ring Metric sizes, units include 3/4 in. NPT, BSPP, BSPT, and -12 (1 1/16–12) SAE O-Ring to meet growing needs of manufacturing industry. Modular connectors are suited for pressure and vacuum testing, filling, and flushing applications.

Michael Smith Engineers Ltd    Surrey   United Kingdom
Jun 20, 2013 Finish Thompson PF, TB, and TBF series drum pumps are available with M5V variable-speed electric motor, which provides 650 W continuous power and infinitely variable speed control. Incorporating bearing retaining system that eliminates any chance of movement, motor helps eliminate problems associated with heat build-up resulting from overloading or voltage fluctuations. Infinitely variable electronic speed control allows precise control of fluid flow.

WILO USA LLC.    Rosemont, IL 60018
Jun 20, 2013 Offering 64 models to meet needs of multiple applications and industries, SCP horizontal split case pumps include sizes up to 500 hp, with capabilities for heads up to 750 ft and flows up to 15,000 gpm, that accommodate temperatures from 18 to 250°F. Horizontally split casing allows replacement of bearings and mechanical seal without disturbing system piping, and double suction design is available for max efficiency. Tongue and groove neck design eliminates rotating assembly seizing.

Atrix International, Inc.    Burnsville, MN 55337
Jun 17, 2013 In addition to tongue and groove design that strengthens filter while minimizing or eliminating potential for leaks, Omega 31700 series, OF612 series, and OF712 series incorporate bodies with 4 radii corners which improve strength and appearance. Width of band area promotes connectivity. These cartridge filters are available for all Omega Plus, Omega Supreme Plus, 3M 497 Series Field Service Vacuums, Katun UltiVac, and UltiVac Deluxe Series Vacuums.

W. L. Gore & Associates, Inc.    Elkton,, MD 21921
Jun 17, 2013 Specifically engineered for outdoor enclosures with volume in excess of 200 L, GORE® PolyVent XL enables internal pressure to remain equalized during changes in environmental temperatures, helping to prevent seal failure. Constructed of breathable membrane, IP69K-rated vent equalizes internal pressure by allowing air to flow freely into and out of housing at rate of 16 Lpm at 12 mbar. GORE® PolyVent XL simultaneously prevents liquid ingress at pressure of 0.3 bar for 60 sec.

Valco Instrument Co., Inc.    Houston, TX 77255
Jun 13, 2013 Cheminert UHPLC Fittings permit direct connection of 360 micron OD fused silica, PEEK®, stainless, or electroformed nickel tubing without use of liners. Because of fitting's fine 2–56 threads, leak-free connection that seals at pressures in excess of 20,000 psi can be formed with manual tool. Fittings in PEEK can be used safely up to 10,000 psi. Supplied with PEEK or stainless nut, fittings include ferrule that is free to rotate but does not twist tube as nut is tightened.

Colder Products Co.    St. Paul, MN 55114
Jun 12, 2013 Featuring ergonomic thumb latch, NS1 Series quick disconnect coupling provides secure, reliable connect and disconnect. Non-spill shutoff valves ensure drip-free disconnects, and drybreak style design minimizes air inclusion. Connection can be made with minimal alignment and allows tubing to rotate freely without kinking/twisting. Constructed from polypropylene and PEEK® materials for strength and chemical compatibility, couplings are available for applications with tubing sizes <1/8 in.

Schroeder Industries LLC    Leetsdale, PA 15056-1025
Jun 12, 2013 Combining KL3 particulate filter with ICF continuous coalescing filter, Bulk Diesel Filter Cart (BDFC) is designed to meet diesel cleanliness requirements of Tier IV high pressure, common rail injection diesel engines. Maneuverable 14 gpm unit, suited for kidney-loop filtration or fuel transfer, weighs just over 100 lb and measures 40 x 22.5 x 21.69 in. Particulate filter is placed upstream to clean fuel, consequently reducing coalescing element change-out to semi-annually or annually.

Beswick Engineering Co., Inc.    Greenland, NH 03840
Jun 11, 2013 Corrosion-resistant stainless steel and brass compression fittings serve applications where metal or stiff plastic tubing is used and aggressive fluids as well as pressure and temperature extremes may be present. Assemblies are leak free due to internal ferrules and O-ring face seal design. Compression fitting intended for use with 4 mm tubing and ¼-28 threads is available; M3, M4, 10-32, M5, ¼-20, and 5/16-24 thread sizes as well as 1/16, 1/8, ¼ in. OD tubing options are also available.

Murata Power Solutions, Inc.    Mansfield, MA 02048
Jun 11, 2013 Designed for sub-1 GHz wireless applications using Texas Instruments CC112x series low power transceivers, LFD21 LTCC (low temperature co-fired ceramic) SMT filter measures 2.00 x 1.25 x 0.7 mm. Model LFD21868MMF has nominal operating frequency centered on 891.50 MHz ± 23.50 MHz and accommodates up to 500 mW transmit power output. Insertion loss is typically better than 1.73 dB transmit and 2.67 dB receive, and antenna port matches to nominal impedance of 50 Ω.

Industrial Innovations, Inc.    Wyoming, MI 49519
Jun 10, 2013 Injector Manifold Assembly package, available for companies using Spra-Rite lubrication system, includes Spra-Rite injector manifold, enclosure interface, pressure regulator, and pressure gauge. Pressurized lubricant is encapsulated within manifold assembly until injection cycle is initiated, and injector manifolds are available using 2, 4, 6, or 8 injectors. Each injector is independently controlled with min spray time of 20 msec, fostering precise control of lubricant volume/placement.

AutomationDirect.com    Cumming, GA 30040-9905
Jun 10, 2013 Available in NPT and BSPT sizes, NITRA Push-to-Connect Pneumatic Male Fittings are constructed with 316 stainless steel bodies and 303 stainless steel gripping collets with internal Viton O-ring to resist washdown situations. Able to withstand pressures up to 290 psi and temperatures up to 390°F, fittings can be used with polyurethane, nylon, and PTFE tubing. Bodies of elbow and tee fittings with threaded connections can be rotated after installation to allow for variations in piping direction.

Mi-T-M Corporation    Peosta, IA 52068
Jun 07, 2013 Equipped with Honda, Subaru, or Mi-T-M engine, Semi-Trash Pumps are available in 2 and 3 in. models, each with total suction lift of 28 ft and max head limit of over 100 ft. Pumps are constructed with silicon carbide seal for leak-proof operation, and precision-molded cast iron impeller and volute for optimized engine performance. Units are suitable for civil engineering, construction, flood relief, and agricultural applications.

Gates Corporation    Denver, CO 80202
Jun 05, 2013 Offering alternative to staple-lock couplings, iLok™ Couplings can be connected to longwall mining machinery in seconds and disconnected in under 2 min. Workers disconnect couplings by cutting and removing cable lock and turning swivel nut by hand, instead of prying staples loose with crowbars or hammering equipment. Using secure, visible locking system, units withstand high impulse applications. TuffCoat® Xtreme™ plating provides red rust protection that exceeds 72-hr SAE standard by 1,000%.

Mott Corporation    Farmington, CT 06032 3159
Jun 05, 2013 Featuring all-metal 316LSS construction that can be heated to 450°C, FLP Series is suited for filtering low pressure, vapor phase dopants used in metal-organic vapor phase epitaxyor, advanced chemical vapor deposition, and atomic layer deposition applications. Open filter media enables passage of low pressure liquid source gas while having enough surface area to remove particles down to 0.003 µm, and is effective at preventing large particle agglomerations from migrating downstream.

Roxtec, Inc.    Tulsa, OK 74146
May 31, 2013 Roxtec CES Conduit Seal™ eliminates problem of water entering conduits and subsequent damage caused to system, fiber coax, and power cables, especially during freezing temperatures. Eliminating need for silicones, butyl, and other sealing masses, this UL/NEMA 3 and IP55 approved cable entry and sealing solution allows use of pre-terminated cables, and can also be installed on existing sites without disconnecting cables with retrofit feature. Seal also protects against effects of rodents.

NewAge Industries Inc.    Southampton, PA 18966
May 31, 2013 Intended for use with plastic and rubber tubing and reinforced hose, Thermobarb® fittings are offered in 5 materials – polypropylene, polyethylene, nylon, PVDF, and brass – that offer different performance properties to meet application requirements. Connections require fitting to be pushed into tubing and secured with clamp; multiple barbs provide tight fit with tubing ID. Sizes range from 1/8–1 in. tubing ID in styles that include tees, wyes, reducers, connectors, adapters, and nipples.

SKF USA, Inc.    Lansdale, PA 19446
May 30, 2013 Suitable for gearboxes, fans, pumps, and electric motors, SKF SPEEDI-SLEEVE Seals are made of stainless steel and are available for shaft diameters from 0.472–8 in. Optimized strength and ductility result in sealing surface that minimizes wear on sleeve and sealing lip during operation. For highly abrasive environments and/or for applications integrating PTFE-filled seals, SPEEDI-SLEEVE is available in Gold versions featuring thin, metallic coating applied to base stainless steel.

Kurt Manufacturing    Minneapolis, MN 55421
May 29, 2013 Compatible with Kurt single-acting 4, 6, and 8 in. vises, portable KHP5000PH provides constant hydraulic pressure and holding power. Pump operates with ordinary shop air at 20–90 psi input and incorporates internal load limiting valve, air exhaust muffler, and air and oil filters. Rated at 5,000 psi, air hydraulic pump is driven by 1 hp pneumatic motor and actuated with hand operated switch lever. Constant pressure is maintained when lever is actuated regardless of system pressure.

Continental Disc Corporation    Liberty, MO 64068
May 29, 2013 HPX-Ta™ Tantalum semicircular scored reverse acting rupture disc is designed for use in corrosive media such as bromine, chlorine, HCL, nitric acid, or sulfuric acid. Holder corrosion resistance can be enhanced by Tantalum lining or coating of holder inlet and/or Tantalum coating of holder outlet. Also available, HPX® Rupture Disc comes in 1–3 in. sizes with burst pressures up to 2,000 psig. Both products are compatible with HPX® Insert, HPX-PT®, or HPX Double Disc holders.