Allegro MicroSystems Inc.
Worcester, MA 01615
Jun 11, 2008 Offered in reverse battery protected packages, temperature-stable and stress-resistant latches have dynamic offset cancellation that reduces residual offset voltage. On single silicon chip, Models A3290 and A3291 include Hall-voltage transducer, small-signal amplifier, chopper stabilization, Schmitt trigger, and short-circuit protected open-collector output to sink up to 25 mA. Onboard regulator allows operation with 4.2-24 V supply voltages with -40 to 125°C operating temperatures.

J. W. Winco, Inc.
New Berlin, WI 53151
May 30, 2008 Offered in blank, tapped, and tapped through hole versions, Wing Nuts have hot stamped, matte shot-blasted finish. They feature slight dimple on ends to permit better grip and provide increased finger contact area. For certain minimum quantities, blank version can be tapped or reamed in inch or metric sizes to meet customer requirements.

Wire Belt Company Of America
Londonderry, NH 03053-7449
May 16, 2008 Designed for use with Flat-Flex® conveyor belts, C-CureEdge® C-shaped end loops provide maximum safety because they will not snag or tangle during shipment, storage, or installation. This diminishes opportunity for damage to conveyor and minimizes risk of accidents from sharp or burred open ends. No conveyor modifications or reconfigurations are required in drive components, shafting, or other parts on conveyor lines, and individual strand stress is reduced on outside edge of belt.

Richco, Inc.
Morton Grove, IL 60680
May 09, 2008 Molded in UL94 V2 Nylon 6/6, RoHS-compliant TFR Series snaps in place to facilitate assembly. Once self-threading screw is installed, grommet expands and securely locks screw and assembled parts in place. Grommet legs are forced outward to help seal mounting hole and protect against dust and moisture. Mounting hole is square to prevent rotation.

DIRAK
Chantilly, VA 20151-1220
Apr 29, 2008 Featuring single-component design that combines function of captive screw and captive nut/cage nut, SNAP LINE 1-035SL Captive-Joiner 9.5 eliminates need to install separate handle. Unit offers tool-less snap-in installation, and is completely installed from front of panel, without insert. Device can also function as slam-to-close latch, requiring only push of panel against frame to ensure latching. Since it will not loosen from panel, fastener is suited for extreme vibration applications.

ERICO, Inc.
Solon, OH 44139-2631
Apr 29, 2008 Without requiring bar-end preparation, sawing, or swaging, LENTON® LOCK coupler installs with standard wrench or impact wrench. Gripping technology provides for development of full rebar strength and improved structural integrity in tension, compression, stress reversal, and dynamic applications. With less than 0.004 in. of slip, completed connection performs similar to continuous piece of rebar and meets/exceeds international building codes and DOT requirements.

Southco
Concordville, PA 19331 0116
Apr 25, 2008 Featuring pull-tab actuation and push-to-close latch engagement, M1-15 latch is constructed of cast stainless steel and suits enclosures that require corrosion-resistance. It has 122 lb max recommended working load rating and also performs in mobile applications where contents of enclosure can shift and create impact load on inside of door. Able to be installed in singe 1.5 in. round hole, latch comes in standard non-locking style and optional locking version.

Guden, H. A., Co., Inc.
Ronkonkoma, NY 11779
Apr 18, 2008 Supplied with holes and cut to length as required, MS35000 series stainless steel piano hinges can serve marine, military, and shipboard applications. They are available in stock lengths or can be supplied to end-user requirements. Able to survive harsh environment and outdoor exposure, these RoHS-compliant hinges can be customized for any design engineering project. Also available is US Navy locker hardware manufactured to BuShips drawing number S-3200-860055.

Tychi Systems
Salem, NH 03079
Apr 18, 2008 BioKnob(TM) allows only users whose fingerprints have been programmed into lock's self-contained memory to turn knob and open door. It stores up to 100 sets of fingerprints, and all programming functions are accomplished directly on device. Fingerprint patterns are transformed by embedded software into template representing fingerprint, which is stored for future verification. Device runs on Li-Ion battery that recharges via AC adapter in 3 hr.

Spiroflow Systems, Inc.
Monroe, NC 28110
Apr 14, 2008 AMC AutoTensioner automatically measures and adjusts rope tension and indicates when rope is worn and needs to be replaced. It applies constant preload to conveyor's rope and disc assembly, compensating for natural changes in length. Pneumatic actuator is anchored at one end of conveyor and applies linear force to free moving return sprocket housing while manually adjustable precision filter regulator protects pneumatic actuator from over-pressure.

PennEngineering
Danboro, PA 18916-1000
Apr 01, 2008 PEM® floating self-clinching fasteners include non-locking Type A4 and self-locking Type LA4 fasteners that provide load-bearing threads in SS sheets as thin as .038 in. and greater with hardness of HRB 88. Available thread sizes range from #4-40 through #10-32 and M3 through M5. All clinching occurs on fastener side of sheet, which allows sheet to remain flush on one side, and RoHS-compliant fastener is permanently locked in place.

Wisair
Tel-Aviv 69710  Israel
Mar 31, 2008 Based on WSR601 single-die CMOS chip, SDIO Wireless USB solution lets vendors embed Wireless USB into portable and handheld electronic devices using Secure Digital Input/Output (SDIO) interface. Design package includes platform for development of embedded Wireless USB device solutions, based on SDIO interface. Using development platform, hardware, and software, developers can implement embedded small form factor module controlled by device side application CPU via SDIO bus.

Custom Service Hardware
Cedarburg, WI 53012
Mar 04, 2008 Offered in 3 types, Hardware Kits feature quiet rollers and non-marring wheels. Kit contains 2 bottom rollers, 2 rolling top guides, 7 rung support rods for steps, fasteners, and instructions. Track kit includes 1 in. dia x 8 ft powder-coated black aluminum track, 2 end stops, support brackets and screws, and steel support dowels. Available in 8, 9, or 10 ft length, which user cuts to desired height, wood ladder kit offers choice of red oak, maple, or cherry wood ladders.

Richco, Inc.
Morton Grove, IL 60680
Feb 26, 2008 RoHS-compliant SEI series provides strong threads in metal sheets that are too thin to be tapped. Products allow for right-angle assemblies and provide alternate to self-clinching fasteners. With design that reduces necessary hardware, series is installed by rotating in side of panel and can be removed by pinching spring leg and rotating. Series is available with No. 6-32 and M4 internal threads.

Spirol International Corp.
Danielson, CT 06239 1434
Feb 25, 2008 Series CL500 roll-formed, insert-moldable Compression Limiters is designed around standard clearances for 6 and 8 mm bolts, while series CL550 is designed with additional clearance around bolts to accommodate greater positional tolerances. Standard material is low carbon steel with trivalent, hexavalent-free zinc plate finish for corrosion protection. They are used to preserve threaded joint's integrity when fastening plastic-to-plastic or plastic-to-metal assemblies.

TietoEnator
Signal Mountain, TN 37377
Feb 13, 2008 Built on modularized architectural framework including software and hardware, Gateway Platform offers turnkey solution for building signaling and/or media gateways. It accelerates development of customer-specific gateway solutions with carrier-grade characteristics, enabling inter-working between various types of telecom networks and nodes. Featuring pre-integrated components, platform executes in closed environment to guarantee signaling capacity and availability.

Brand Preference Development Co./Protex® Latches
St. Louis, MO 63104
Feb 08, 2008 Measuring 300-350 mm in length, 80 mm wide, and 38 mm in height, Protex® heavy-duty adjustable latch is suitable for variety of off-highway vehicles with 7,000-12,000 lb rated axles, including medium range trailers, tandem duals, livestock, and flatbed goosenecks. Unit comes with matching boltable catchplate.

Advanced Machine & Engineering Co.
Rockford, IL 61103
Jan 24, 2008 Suited for applications where space is limited, Spieth Type MSF Locknuts utilize clamping screws with socket head similar to TORX system screw to optimize handling, mounting, and service life of tools used for tightening. Units feature Spieth locking principle, which provides vise-like locking of locknut.

J. W. Winco, Inc.
New Berlin, WI 53151
Jan 24, 2008 Manufactured from black glass-filled nylon plastic, inch-size star knobs have matte finish and zinc-plated, steel, molded-in hub. Boss face is exactly square to bore and made of steel to prevent edges from breaking. Available in metric and inch sizes with maximum heat tolerance of 110°C, knobs come in tapped or blind bore types. Special bores and threads are available upon request, as are other modifications such as cross pins and set screw holes.

Luminary Micro, Inc.
Austin, TX 78746
Jan 23, 2008 Stellaris® Brushless DC Motor Control Reference Design Kit (RDK-BLDC) contains everything needed to evaluate and develop control designs for 3-phase brushless DC motors. Along with motor, this 4-quadrant controller is supplied with built-in CAN and Ethernet interfaces, graphical control program for Windows(TM), and 32-bit Stellaris LM3S8971 MCU with 256 KB single-cycle internal Flash. Accompanying cables, source code, and documentation are also included.