Kurt Manufacturing    Minneapolis, MN 55421
May 14, 2013 Engineered for locating, attaching, and removing fixtures, subplates, and vises on machining centers, PinLock™ System consists of high-precision pins, bushings, and liners that provide locating and locking repeatability up to ±.0005 in. Shanks and bushings are precision machined of heat-treated, alloy steel with black oxide finish. Helical extraction design and pin feature aids in overcoming binding in side load conditions and optimizes removal of PinLock in any application.

Zero-Max, Inc.    Minneapolis, MN 55441 5537
May 01, 2013 Capable of handling torque from 21,000–200,000 lb-ft, ETP Hydropress Bushings utilize hydraulic pressure contained in double-walled sleeve to provide precise fastening of components on shafts from 80–200 mm diameter. Both radial and axial connection to shaft is made using grease pump for mounting. Once mounted and pressurized, conical angle of outer sleeve locks device into position, forming tight, continuous connection between shaft and mounted component.

Slideways, Inc.    Worcester, MA 01605
Apr 23, 2013 Compliant with Food Safety Modernization Act, X-Ray Detectable Components help minimize contamination problems for food industry. Products such as wear strips, sprockets, chain guides and tracks, mixer components, bushings, and bearings are available in Acetal, UHMW, Nylon, and PEEK. Detection of parts as small as 2 mm³ at speeds as fast as 250 fpm is standard.

Bridgeport Fittings, Inc.    Stratford, CT 06497
Dec 05, 2012 Available in trade sizes from ¾–4 in., Mighty-Rite® SGB Series helps contractors safely install electrical systems. Units can be installed before pulling wire or after, eliminating rework. This feature also makes pulling larger conductor wire easier when contractors can install grounding bushings after pull. Equipped with 150°C rated liner, cULus Listed bushings feature captive screws and hinged design that adjusts and aligns, even in tight spots.

Heyco Products    Toms River, NJ 08753
Nov 20, 2012 Designed for 020–.063 in. thick panels and mounting hole diameters of .500–1.093 in., HEYCo-molded™ Liquid Tight Break-Thru Plugs consist of co-molded nylon and elastomer parts. They function as liquid tight plugs with IP 67/68 rating and may also be pierced by round wire, cable, or tubing to function as liquid tight bushings with same resulting IP rating. Locking fingers snap into holes in fractional increments via fingertip pressure and withstand push back force greater than 35 lb.

Igus, Inc.    East Providence, RI 02914 0349
Nov 15, 2012 Fire retardant and classified according to UL94 with V0 standards, iglide® GV0 polymer plain bearing offers max short-term application temperature of 410°F and max long-term application temperature of 266°F. V0 classification means this material is suitable for use in areas with high fire-protection regulations, including aircraft, automobile, and rail vehicle interiors, as well as elevator and escalator technology. Bushing also exhibits wear resistance on most shaft materials.

Igus, Inc.    East Providence, RI 02914 0349
Oct 03, 2012 Injection-molded, self-lubricating, maintenance-free iglide® Q2 bushings exhibit low chance of deformation that promotes extended service life in heavy-duty pivoting applications. Able to withstand radial loads up to 11,023 lb/in.², these heavy-duty plastic bushings also exhibit resistance to wear.

Heyco Products    Toms River, NJ 08753
Jun 25, 2012 Made from nylon 6/6, Thin Panel Bushings are designed for panels as thin as .020 in. and are available for .218-.875 in. diameter holes. Bushings feature locking fingers that snap into holes with fingertip pressure in fractional increments up to maximum panel thickness, and can withstand push back force of greater than 35 lb. In addition to creating smooth insulated holes, bushings insulate and mechanically protect electrical/telecommunications cables, tubing, hose, and rope.

Zero-Max, Inc.    Minneapolis, MN 55441 5537
Jan 25, 2012 Providing concentricity to .001 in. TIR, ETP Express Bushings handle torque ranges from 40-6,400 lb and are available in 20, 40 and 60 mm sizes. Shaft-locking bushings provide mounting/dismounting capabilities with only one radial screw. They are designed for locking gears, cams, and timing pulleys into position in tight spaces. Bushings handle temperature ranges from -22°F to 180°F. Uniform pressure prevents damage to surfaces and enables use of shafts without keyways.

Igus, Inc.    East Providence, RI 02914 0349
Aug 29, 2011 Made of 54% raw, renewable materials, iglide® N54 Self-Lubricating Bushings use vegetable oil rather than crude oil and are suited for low-load applications in consumer products, general mechanical engineering, and furniture. Every bushing uses solid lubricants embedded inside millions of tiny chambers that cannot be pressed out. Since bushings do not require oil or grease, no contaminants are released into environment.

Heyco Products    Toms River, NJ 08753
Jul 11, 2011 Designed for mounting hole diameters from .375-2.0 in. and panel thicknesses up to .125 in., Reducer Snap Bushings insulate and mechanically protect electrical and telecommunications cables, tubing, hose, rope, and utility lines. Products also provide neater look where cable OD to bushing ID clearance is minimized. Manufactured from 6/6 nylon in standard black color, bushings insert into mounting holes with fingertip pressure and withstand push back force of 35 lb.

HASCO Hasenclever GmbH + Co KG    Ludenscheid D-58513  Germany
Jun 20, 2011 Able to withstand operating temperatures up to 180°C, Z13/... Series is designed primarily for precise guiding of ejector plates in injection molding tools, compression molds, and diecasting molds, and for guiding of mold plate assemblies. Guide ball bearings roll continuously in rotating ball tracks, virtually eliminating possibility of denting guide pillar. Installation of Z13/... Series in H7 drill holes is possible in tight spaces.

Advanced Anti-Vibration Components - AAC    New Hyde Park, NY 11040
Jun 03, 2011 Made of silicone gel with brass collar, V10Z61MA and V10Z61MB Series Bushings are available in 5 models with collar ID of .12-.16 in. and operating temperature range of -40 to +392°F. Units isolate vibration in low frequency applications with loads ranging from 0.11-17.64 lbf per mount. Bushings are suited for isolating electronic equipment such as speaker systems, turntables, and cameras.

Heyco Products    Toms River, NJ 08753
Apr 14, 2011 Designed for 0.500-1.093 in. dia mounting hole and .062-.125 in. panel thickness, Smooth Bore Bushings eliminate sharp through-hole edges to protect wires and may also be used as bushings for rotating shafts. Manufacture is of 6/6 nylon, and standard color is black. Inserted into mounting holes with fingertip pressure, products features extra internal insulating sleeve that creates smooth bore and prevents locking fingers from protruding into bushing ID.

Kurt Manufacturing Co., Industrial Products Div.    Minneapolis, MN 55413 1540
Apr 06, 2011 Consisting of high precision pins, bushings, and liners that provide locating repeatability up to ±.005 in., PinLock(TM) System facilitates attachment and removal of fixtures, subplates, and vises from machining centers. Helical extraction design aids in overcoming binding in side load conditions. Precision machined of heat-treated, alloy steel with black oxide finish, liner bushings are available for fixture plate thicknesses of 0.75, 1.00, 1.50, and 2.00 in.

Lapp USA    Florham Park, NJ 07932
Mar 11, 2011 Resistant to oil, grease, UV rays, and ozone, SKINTOP® CUBE consists of frame and flexible clip sealing modules, which are available in 4 clamping ranges of 4-6, 6-9, 9-12, and 12-16 mm. After installation, cable is secured against vibration, strain relieved, and sealed in accordance with IP64. Matching, glass-fiber-reinforced polyamide frames, available for 16-pin or 24-pin connector openings, allow 8-10 cables to be mounted in clearly arranged manner.

Hendrickson Trailer Suspensions Systems    Canton, OH 44707 2641
Dec 14, 2010 Intended for use with company's proprietary walking beams, part No. 34013-188L rubber rotating bar pin end bushing conserves installation time by eliminating need to pay attention to bar pin angle. Once pressed in, bar pin can be turned with shop wrench or similar tool to required axle angle. Product includes set of shims to facilitate axle alignment as well as required fasteners to complete installation.

QTC Gears - Quality Transmission Components    Garden City Park, NY 11040
Nov 30, 2010 Constructed of carbon steel, SV... Series of module 1.667 involute splined shafts and bushings feature thermal refined heat treatment for optimized abrasion resistance. Tooth hardness ranges from 225-260 HB, lengths are available from 170-300 mm, and bushing bore sizes vary from 13.7-26.7 mm.

Graphite Metallizing Corporation    Yonkers, NY 10703
May 20, 2010 Made of graphite/metal alloy formed from molten metal, graphite, and carbon, GRAPHALLOY® Type 1017 Self-Lubricating Bushings contain no oil to contaminate conveyed materials and can withstand dust, chemical attack, caustic liquids, and high temperature environments. GRAPHALLOY does not deform under load and maintains dimensional stability. Offering continuous-duty operation, bushings are suitable for applications where maintenance intervals are infrequent.

Graphite Metallizing Corporation    Yonkers, NY 10703
Apr 20, 2010 Made from graphite/metal alloy formed from molten metal, graphite, and carbon, 117 Series of GRAPHALLOY® bushings are available in 2 primary grades for high temperatures, both with FDA acceptance. Many grades of GRAPHALLOY® can handle temperatures to 750°F in air, while special grades provide service up to 1,000°F and higher in non-oxidizing atmospheres. Applications include bakery ovens, heat treat furnaces, and glass plants.