Fasteners & Hardware

Architectural and Civil Engineering Products, Fasteners & Hardware, Mechanical Components and Assemblies, Services

Castings reduce road renovation time.

Mar 20, 2002

Final Cut castings eliminate need for pavement removal around street castings. Cover and rim elevation of manholes, catch basins, and hand holes can be raised by 1 1/2 in., regardless of thickness of cover. Cast iron construction provides corrosion resistance and durability. Combination of Final Cut rim, riser and cover allows use of BMPs for control of erosion and sedimentation. Read More

Electrical Equipment & Systems, Fasteners & Hardware

Battery Straps protect rechargeable battery packs.

Mar 14, 2002

MF-SVS, MF-VSN and MF-VS Multifuse(R) Polymeric Positive Temperature Coefficient straps, with resettable fuses, enhance safety and performance of rechargeable batteries. MF-SVS has initial resistance as low as 14 mOhms and protects Lithium and Ni-MH chemistry cells; MF-VS210N, for GSM battery packs, and MF-VS170N, for lower pulse current applications, have maximum voltage of 12 V, and maximum... Read More

Fasteners & Hardware, Mechanical Power Transmission

Sheaves and Shackles pull fiber optic cable.

Mar 14, 2002

Lightweight Bicycle Wheel sheaves are available in 24, 32 and 40 in. sizes to accommodate bending radius of common sizes of fiber optic cable. Split-sheaves allow larger sheaves to fit through smaller manhole openings. All components are permanently attached to shackle, eliminating concern about loose or lost parts. Underground and aerial shackles are available. Underground shackle has moveable... Read More

Fasteners & Hardware

Locking Bushings provide positioning on sliding shafts.

Mar 13, 2002

ETP-Octopus(TM) hydraulic shaft-locking bushings offer uniform and repeatable locking pressure, and can be set up for frequent locking/unlocking of linear slides from remote switching locations. Bushings are corrosion resistant with either bronze or steel sleeve bores. They are available in 3 models with pressure ranges to 6500 psi. Model C is available with bore sizes from 30 to 100 mm; Models O... Read More

Fasteners & Hardware

Turning and Milling Inserts are PVD coated.

Mar 12, 2002

SpectraTurn(TM)and SprectraMill(TM) inserts are coated with TiAln or AlTiN for edge strength and wear resistance. Heat produced in cutting process is carried away by chip. TiAlN coated insert grades are suitable for dry milling and for high-speed turning. AlTiN coated inserts are ideal for milling titanium and titanium alloys. Read More

Fasteners & Hardware, Portable Tools, Textile Industry Products

Attaching Tool inserts fasteners through fabrics.

Mar 12, 2002

Portable MicroTach(TM) hand tool inserts 0.172 in. T-End fasteners through fabrics and paper or cardboard packaging, replacing thread, pins and metal staples. Fasteners can hold 2 pieces of fabric tightly together or secure fabric to packaging. Tool is made of polycarbonate material for use in factory environments. It is available with brush anvil, which can serve as firm fastening application... Read More

Fasteners & Hardware, Robotics

Fastening System retains 6000 points or 100 programs.

Mar 12, 2002

SCARA Fastening System is a screw assembly robot that employs ASG electric torque-control screwdrivers for repeatable fastener torque ranging from 4.0 oz-in. to 39.0 lbs-in. With no workpiece weight restrictions, SCARA robot is suitable for payloads of any weight. Repetitive position accuracy is +/-0.01 mm in Z axis, and +/-0.02 mm in X and Y axis. Set-up and training pendant uses plain English... Read More

Fasteners & Hardware

Coil Inserts do not require tang removal.

Mar 08, 2002

Kato Tangless(R) CoilThread(R) high-tension coil inserts are installed with hand, air-driven or electric tools featuring head that grips and drives insert. Bi-directional design eliminates need to orient each part, and does not require special tang break-off and tang removal tools. Inserts shrink when installed, and spring-like tension of coil locks inserts into place. Read More

Electrical Equipment & Systems, Fasteners & Hardware

Cable Lock protects tools and equipment.

Feb 27, 2002

Python(TM) No. 8413 adjustable locking cable is suitable for protecting ladders, power tools, cargo racks, and other outdoor equipment. It has 6 ft by 10mm vinyl coated braided steel cable with cinch-locking body that provides infinite locking positions along length. Locking cam allows easy cinching for tight fit, while molded bumper/grip protects against scratching. Removable wafer cylinder... Read More

Fasteners & Hardware

Flame Retardant Fasteners meet aerospace standards.

Feb 27, 2002

Scotchmate(TM) reclosable polyester Series SJ3586FR and SJ3587FR meet Federal Aviation Administration's 60-sec and 12-sec vertical burn tests (FAR 25.853). Hook and loop interlocking can be opened and closed for access or frequent repositioning applications such as seat cushions, interior trim covers, and wall panels. Sound and vibration dampening helps reduce squeaks and rattles. Fasteners are... Read More

Fasteners & Hardware

Reverse Expansion Insert presses into plastic hole.

Feb 27, 2002

Suitable for strengthening plastic joints, Series 18 brass reverse expansion insert is used in applications where bolt enters insert from headless end rather than from headed end. Its head provides high level pull-through resistance and its diamond knurl provides directional torque resistance for bolt installation. Unit does not require any specialized insertion tools, so it can be installed by... Read More

Fasteners & Hardware, Laboratory and Research Supplies and Equipment

Laboratory Glassware Washers fit capacity needs.

Feb 01, 2002

Model G 7827 Large Capacity Glassware Washer is suitable for high-throughput, centralized wash areas. Model G 7825 Medium Capacity Glassware Washer is suitable for centralized wash areas where space is at premium. Both models are under-counter type. Read More

Fasteners & Hardware, Safety & Security Equipment

Anchorage Connector provides temporary fall protection.

Jan 25, 2002

OSHA-compliant Disposable Concrete Anchor Strap provides secure point of attachment in concrete construction. Strap loop is positioned on rebar and concrete poured over loop and adjoining protective nylon sleeve. Safe anchorage exists once concrete sets. When anchorage is no longer needed, workers simply cut protruding strap. Abrasion-resistant 1 3/4 in. wide nylon webbing, with steel D-ring,... Read More

Fasteners & Hardware

Core Pins are offered in 500 diameters.

Jan 23, 2002

M-2 high speed steel core pins are available in every decimal dia from 0.010 to 0.505 in. in 0.001 in. increments, with 0.0002 in. or 0.0003 in. dia tolerances. Double-tempered to Rc 60-63, pins are wear-resistant and permit close spacing without modification. They are available in 2, 2 1/2, 3, 4, 6 and 8 in. lengths and are suited for glass-filled applications. Read More

Fasteners & Hardware

Metal Thread Inserts fit wood and composition board.

Jan 22, 2002

Three metal thread inserts install without need for special tools. Knife thread inserts, available with coarse and fine internal threads, furnish holding power in hard woods such as oak, maple, and mahogany. Finsert thread inserts provide strong metal threads in softer materials, and prevent splintering, splitting, and thread pullout. Hex Drive thread inserts are for soft materials such as pine,... Read More

Electrical Equipment & Systems, Fasteners & Hardware

Cable-Tie Hook provides secure and removable mounting.

Jan 22, 2002

Type TDO self-clinching hook provides attachment points for mounting tie-bundled wires to electronic chassis or enclosures. It provides capability for users to temporarily remove wire bundle from mounting point. Hook installs in sheets from .040 to .125 in., uses no adhesives, which can fail over time, promotes EMI/RFI shielding, and reduces possibility of contamination by eliminating need for... Read More

Fasteners & Hardware

Ceramic Inserts triple cast iron milling productivity.

Jan 21, 2002

Fix Perfect ceramic inserts have 8 true cutting edges and run 3 times faster in cast iron milling operations than conventional carbide inserts. Inserts are made of Kyon3500 ceramic that has shock resistance needed to perform roughing operations on cast iron at very high speeds, chiploads, and depths of cut. On-edge or tangentially mounted insert puts 1/2 in. of carbide behind cutting edge of 0.5... Read More

Fasteners & Hardware

Ceramic Cutters cut faster than carbide.

Jan 21, 2002

Kyon 2100 grade silicon nitride based ceramic inserts boost productivity 100% to 500% on high temperature alloys by machining at cutting speeds of 3,000 sfm, 10 to 25 times faster than carbide grades. It performs rough milling of nickel, cobalt, and iron based heat resistant alloys, and rough machining of high temperature alloys such as Waspalloy, Haynes 25, Inconel 718, Stellite, and similar... Read More

Fasteners & Hardware

High Density Patch Cord has carrier-class reliability.

Jan 17, 2002

Model LX.5® Fiber Optic Patch Cord deals with growing fiber density without sacrificing network integrity. LX.5 doubles SC density, while its adapter fits into SC's footprint. Available in singlemode and multimode versions, it maintains single circuit access, and incorporates safety shutters on both connector and adapter body. Read More

Fasteners & Hardware

Pushbutton Lock includes audit trail.

Jan 17, 2002

Trilogy DL2800 electronic digital lock is designed with time/date stamp for printable record of all electronic activities. Events are logged within 1 sec, and unit stores up to 1,000 events. DL2800 is weather resistant with operational temperature ranging from 151 to -20 °F. It provides 200 user codes, 150 scheduled events, timed entry from 5 to 15 sec, and temporary lockout feature that locks... Read More