AutomationDirect.com
Cumming, GA 30040-9905
Jul 03, 2009 ZIPport(TM) panel interface connectors mount on outside of electrical control panel boxes and act as pass-through connections, allowing operator to interface with PLCs and other programmable devices without opening control box. Units include standard reset 3 A circuit breaker and are available with single/duplex/GFCI power outlets as well as no-power option. Designed for frame sizes 6-48, communications connectors available include D-sub, RJ45, RJ12, USB, Ethernet, and Data Highway.

Hartmann Electronic
Springfield, OH 45505
Jul 02, 2009 Offering 19 VXS slots and 2 switch slots, VMEbus Switched Serial backplane connects every switch to every VXS connector. Slots include 1 VME64x slot and 18 payload slots which can be connected, with slots J1/J2 being VME64x slots and J0 either VXS or payload slot. Transmission rate is 2.5 GB/sec for every slot simultaneously. Both VITA 41.1, for Infiniband, or VITA 41.2, for rapid I/O, are possible.

Bomar Interconnect Products
Ledgewood, NJ 07852
Jul 02, 2009 With 75 W interfaces rated to 8 GHz and engineered to only mate with 8 GHz parts, BMR series female type connectors are designed to mount to underside of PCB to support optimal grounding and inductance. They feature open-top design and contact pin placement to enable low overall capacitance, and ensure integrity of split satellite signals when employed in RF circuits. Parts are manufactured of precision-machined brass with gold-plated contacts to support low return loss.

ITT Corporation
White Plains, NY 10604
Jun 30, 2009 Designed for low-pressure water immersion or fording applications, KJAYA Series provides hermetic sealing of 0.01 micron cu-ft/hr for pressure differentials of 15 psi. It is available in sizes 9-25 in wall and jam-nut mounting receptacles and is water immersion sealed to 10^-7 cm³/sec. Meeting all MIL-STD-810 and IP67 water immersion requirements, connector is suited for variety of applications including integrated avionics, radar, electronic warfare systems.

ITT Interconnect Solutions
Santa Ana, CA 92705
Jun 25, 2009 Offering contact counts of 1-600, Chip-on-Flex (CoF) connectors are available in rack and panel, circular and D-subminiature configurations. Filter design features one standard flex per layout and utilizes flexible circuit internal to connector, with chip capacitors surface-mounted on small pad adjacent to feed-thru contact. Tested to MIL-DTL-38999 Series III mechanical shock, vibration, and high altitude DWV specifications, connectors exceed 1,000 cycles of thermal shock per MIL-STD-1344.

Neutrik
Lakewood, NJ 08701
Jun 22, 2009 Providing optional screen to chassis grounding and sealing gasket for lockable and watertight digital interface connection, HDMI 1.3 feedthrough connector models NAHDMI-W and NAHDMI-W-B are suited to transmit any digital TV and PC video format including HDTV. Universal D-Shaped chassis connectors are available with either nickel or black housing.

Wireworks Corp.
Hillside, NJ 07205
Jun 18, 2009 Adaptable BG Unisex XLR Cords match up MusiLUX microphone cable or AES/EBU digital cable with convertCON 3-pin connectors that feature sliding housing to convert between male and female connector. Used in microphone and line level applications, units allow users to connect variety of gear without need to consider XLR connector gender. They are available in convertCON to convertCON, convertCON to XLR3 male, convertCON to XLR3 female, and convertCON to ¼ in. TRS configurations.

Aries Electronics, Inc.
Bristol, PA 19007-6810
Jun 17, 2009 Offering standard pin 1-to-pin 1 routing connection scheme, which can be customized to accommodate any connection requirement, Fine Pitch Bump Adapters enable use of any SMT IC device on pitch of 0.4 mm or higher to 0.5 mm pitch PCBs designed for TSSOP and QFP packages. Adapter boards are fabricated from 0.032 in. thick FR4 or Rogers 370 HR, with ½ oz copper traces on both sides. Operating temperature is up to 221°F for FR4 versions and 226°F for lead-free version.

Molex Inc.
Lisle, IL 60532-1682
Jun 12, 2009 HDMI Type D connector is 19-pin D-Subminiature unit that meets electrical and mechanical specifications of HDMI Specification 1.4. Designed for mobile phone manufacturers, PCB receptacle connector allows mobile device users to display HD video, photos, and other content from devices onto full-size flat panel TV screens.

Neutrik
Lakewood, NJ 08701
Jun 12, 2009 Providing IP-protected and lockable data connection, USB/Firewire Chassis Connector offers optional screen-to-chassis grounding for improved shielding effectiveness. Designed to address digital interface problems associated with audio/video networks, IT equipment, and digital recording studios, connector with D-style housing is suited for audio networking and integration of computer-based equipment into audio systems.

Harwin, Inc.
New Albany, IN 47151
Jun 09, 2009 Available in cable-to-cable, cable-to-board, and board-to-board versions, fast-mate 101Lok Datamate Connectors require 101° turn to ensure security of retention device. Connectors use hardware tensioned by coil spring to minimize time required to mate connector halves. Spring tensioning also helps resist vibration in rugged environment applications such as aerospace.

SmartVM
Cleveland, OH 44122
Jun 09, 2009 Video Switch enables up to 8 computers to share one monitor, projector, or any other video display with VGA port while maintaining clear and sharp images. Video extenders, also available, support long-distance transmission of VGA video over standard Cat5/5e/6 UTP cable; kits allow for adjustable signal length and equalization. Offered in 2 models, Digital VGA Splitter suits applications where same image from one PC with VGA video needs to be displayed on up to 16 VGA monitors.

Tripp Lite
Chicago, IL 60609
Jun 08, 2009 Able to directly support up to 4 remote monitors, Model B132-004 extends VGA video signal up to 500 ft from source, while Model B132-004A extends both video and audio. Range is extendible up to 1,000 ft using low-skew Cat5 patch cable. Supporting video resolution up to 1,920 x 1,440 at 500 ft, rackmount extenders/splitters are compatible with VGA, SVGA, UXGA, and WUXGA displays. Equalization and Gain adjustment screws assure clear picture.

Binder-USA, LP
Camarillo, CA 93012
Jun 08, 2009 RD24 Series 692 7-pin overmolded connectors are commonly used for power supplies in oil and gas industry and various commercial applications. Cordsets offer male or female, straight or right angle connectors. Rated current up to 10 A per contact is possible, and when properly mated they are IP67 rated to protect connection from ingress of liquids and debris. Each connector is constructed with plastic shell molded onto 2 m PVC UL approved cable; custom cable lengths are available.

Ironwood Electronics, Inc.
St. Paul, MN 55121
Jun 08, 2009 Giga-snaP(TM) BGA SMT adapter pair consists of SF-BGA316C-B-62F female sockets with machined pins epoxy over-molded into assembly that matches male pin LS-BGA316C-61. Soldered to PCB using standard soldering methods without warping, SF-BGA316C-B-62F allows 0.8 mm pitch, 17 x 17 mm body, 20 x 20 array Analog Device ADSP-BF539/ADSP-BF539F ICs to be socketed and operate in demanding automotive applications. Both adapters are constructed with high temperature FR-4 bodies.

Molex Inc.
Lisle, IL 60532-1682
Jun 05, 2009 Featuring .016 in. pitch, SlimStack(TM) Connectors offer ultra-narrow width of .102 in. and .039 in. profile. Units are available in 20-80 circuits and are rated at 50 V and 0.3 A. Housing allows for PCB tracing patterns to be run underneath connector, while gold-plated soldering tabs provide secure PCB retention and electrical grounding. Miniature, surface-mount units are suited for tight-packaging applications such as mobile phones, digital cameras, or portable audio units.

ATEN Technology, Inc.
Irvine, CA 92618
Jun 02, 2009 Comprised of VS1504/VS1508 CAT5 A/V splitter and VB552 VGA over CAT5 repeater plus audio, ATEN Media Distribution Solution distributes video and audio content to up to 3,000 displays over CAT5 from single input source. Digital signage solution features 2 serial RS-232 channels, enabling fully interactive installations with touchscreen displays. Displays can be mounted in most optimal locations, while hardware providing multimedia content remains secure in remote location.

Hirose Electric USA, Inc.
Cupertino, CA 95014
Jun 01, 2009 Featuring insulation resistance of 1,000 MW at 500 Vdc, with contact resistance of 100 mW at 1 mA, DM3 Series of card connectors are available in 3 different configurations for compatibility. DM3AT/DM3BT Push-Push connectors feature card ejection travel of 4 mm for easy hold and removal of card, while DM3C hinge connectors have metal cover that guides card during insertion and removal. DM3D push-pull card connectors come with partial card insertion hold, preventing card from fall-out.

FCI
Etters, PA 17319
May 28, 2009 HCI® High Power series is designed to supply additional power at interface between daughter cards and backplanes or midplanes in chassis-based platforms. These standalone modules are rated for up to 75 A per contact, without exceeding 30°C temperature rise (no airflow). In addition to 1 x 2 and 1 x 3 power contact configurations, 2-position module is available with integrated guide between 2 power contacts. Series offers up to 261 A/in. linear power density.

Hirose Electric USA, Inc.
Cupertino, CA 95014
May 28, 2009 Comprised of flexible printed circuit (FPC) and flat flexible cable (FFC) connectors, FH12 Series is available with 0.5 and 1.0 mm contact pitches. Half-tuning fork contacts maintain standard force without relying on connector housing, while flip-lock actuator, which requires 6.9 N of force, eliminates need for side latch and has mounted PCB height of 2.0 mm. Available in top or bottom contact point configurations, series has 0.5 Adc current rating, with 50 Vac voltage rating.