Voltage-Controlled Oscillator uses internal SAW resonator.
Surface-mount M650 Series uses high Q resonator, operating at fundamental frequency of end unit, to provide low-jitter frequency translation in telecommunications applications. Oscillator has 3.3 V operation, output frequencies from 155 to 900 MHz, and ground plane for added phase noise performance, with -93dBc/Hz@1KHz offset typical. Applications include clock smoothing, frequency translation,...
Read More »Radial Resistors are available from 1 Ohm to 100 Meg.
CK06 Style package with ratings of 400 Volts, 0.75 Watt at +125 deg C Caddock's Type MK132V/MK632V non-inductive, precision power film resistors are available in the compact CK06 package over the entire ohmic range from 1 Ohm to 100 Meg. Tolerance of 1% is standard and TC is 50 ppm/°C from 5 ohms to 5 Meg. The compact MK resistor with its 0.75 Watt and 400 Volt ratings can replace many different...
Read More »Ballast operates 57-watt fluorescent lamp.
SmartMate(TM) ICF-2S42-M2 ballast is designed to operate 1 triple compact fluorescent lamp, which provides approx 4,300 initial lumens at 25 deg C. Ballast is available with length mounting feet or bottom-mount PEM studs, and single-entry or dual-entry connectors. IntelliVolt(TM) universal voltage allows operation on systems ranging from 120 to 277 V, 50/60 Hz. Ballast offers lamp end-of-life...
Read More »Interconnect System has phosphor bronze contacts.
HARRISBURG, Pa., February 12 - Tyco Electronics Corporation today introduced the AMPMODU Micro Interconnect System. The AMPMODU Micro Interconnect System is based on high-density 0.8mm centerline contacts. It is designed for cable-to-board, cable-to-cable, and board-to-board applications. The low profile, high-density design is well suited for applications with tight space constraints. The first...
Read More »EMI Filters 101: Everything You Need To Know
In this eBook, we'll discuss everything you need to know about EMI filters, including their importance, regulatory requirements, and different types.
Read More »Receptacles support SCSI and FC-AL systems.
SCA-2 receptacles consist of staggered contact heights which enable hot-plugging. Alignment guides at both ends house grounding contacts and allow blindmateability. SCA-2 receptacles are installed on backplane to mate directly with SCA-2 plugs installed on disk drive. Tail configurations include through-hole pin and press-fit compliant pin. 80-pin receptacle supports SCSI-3 protocol, while 40-pin...
Read More »Digital Signal Processor operates at 250 MHz.
ADSP-TS101S TigerSHARC DSP offers 250 MHz clock rate, 1500 MFLOPS performance and native support for 8, 16, 32, and 40-bit data types. It has 1.5 W power dissipation, 6 Mbit of on-chip memory, 14 channel zero-overhead DMA engine, integrated SDRAM controller, parallel host interface, cluster multiprocessing support, and link port multiprocessing support. Applications include data acquisition,...
Read More »Radial Resistors are available from 1 Ohm to 100 Meg.
CK06 Style package with ratings of 400 Volts, 0.75 Watt at +125 deg C Caddock's Type MK132V/MK632V non-inductive, precision power film resistors are available in the compact CK06 package over the entire ohmic range from 1 Ohm to 100 Meg. Tolerance of 1% is standard and TC is 50 ppm/-°C from 5 ohms to 5 Meg. The compact MK resistor with its 0.75 Watt and 400 Volt ratings can replace many...
Read More »Ballast operates 57-watt fluorescent lamp.
SmartMate(TM) ICF-2S42-M2 ballast is designed to operate 1 triple compact fluorescent lamp, which provides approx 4,300 initial lumens at 25 deg C. Ballast is available with length mounting feet or bottom-mount PEM studs, and single-entry or dual-entry connectors. IntelliVolt(TM) universal voltage allows operation on systems ranging from 120 to 277 V, 50/60 Hz. Ballast offers lamp end-of-life...
Read More »Interconnect System has phosphor bronze contacts.
HARRISBURG, Pa., February 12 - Tyco Electronics Corporation today introduced the AMPMODU Micro Interconnect System. The AMPMODU Micro Interconnect System is based on high-density 0.8mm centerline contacts. It is designed for cable-to-board, cable-to-cable, and board-to-board applications. The low profile, high-density design is well suited for applications with tight space constraints. The first...
Read More »Receptacles support SCSI and FC-AL systems.
SCA-2 receptacles consist of staggered contact heights which enable hot-plugging. Alignment guides at both ends house grounding contacts and allow blindmateability. SCA-2 receptacles are installed on backplane to mate directly with SCA-2 plugs installed on disk drive. Tail configurations include through-hole pin and press-fit compliant pin. 80-pin receptacle supports SCSI-3 protocol, while 40-pin...
Read More »Optimize Your Workforce with Weavix™ by PK Industrial
The Weavix™ platform takes productivity, quality, and visibility to a new level by providing better communication and real-time KPIs. Check out the video to learn more!
Read More »