Electronic Components & Devices

Electronic Components & Devices, Optics & Photonics

Optical Jumper provides network monitoring.

Apr 22, 2002

Integrated optical/tap jumper can be utilized in any optical transport network such as voice, video, and data systems with optical signals. Tap/monitoring port can be added to any standard patch panel within existing network with no additional frame space. Jumper is also suitable for wavelength division multiplexing and optical power splitting applications. Read More

Electronic Components & Devices

Multi-Channel Amplifier outputs high voltages.

Apr 22, 2002

Dual Channel MA01 delivers up to 330 V, at peak output currents of 120 mA per channel, for loads such as MEMS-based optical switching, piezo positioning systems, ink jet printers, electrostatic deflection and push-pull applications. Precision, monolithic IC provides power bandwidth of 26 Khz at full output voltage. Each channel can operate independently or both channels can be bridged for 660 V... Read More

Electronic Components & Devices, Sensors Monitors & Transducers

Amplifier/Conditioner offers side load rejection.

Apr 19, 2002

System combines SW0 (universal/tension or compression) and TM0-2 (stand alone bench top amplifier/conditioner), and is suitable for industrial and OEM force measurement and weighing applications. TM0-2 provides excitation, balance, and span adjustment via precision 10 turn pots and shunt calibration. SW0 load cell is offered in ranges from 1,000 to 50,000 lbs. Read More

Electronic Components & Devices, Mechanical Power Transmission

Transducer Amplifier for load cells and pressure sensors.

Apr 19, 2002

CMJ-CEB has bi-polar output of ±5 volts, plus 4 to 20 mA and 0 to 10 V outputs, all field selectable using board jumpers. It is available in single board or DIN rail mount versions, or in environmentally sealed enclosure, and can be used in conjunction with M2S relay board for high-low level control, with relay contact closures. Read More

Electronic Components & Devices, Optics & Photonics

Preamplifier uses avalanche photodiodes.

Apr 19, 2002

C30659-Series includes low noise Gasfet front end, avalanche photodiodes, and hybrid preamplifier in single modified 12-lead TO-8 package. Avalanche photodiodes can be either silicon or indium gallium arsenide and emitter follower is used as output buffer stage. It has strong response between 400 and 1700 nanometers. To obtain wideband characteristics, output of preamp should be ac coupled to... Read More

Electronic Components & Devices

RF Inductors withstand shear test to 4.4 lbs.

Apr 18, 2002

SMRF 1812 surface mount inductors provide inductance values from 1.0 to 1000 microHenries and current ratings from 450 to 30 mA. They exhibit resistance to thermal shock, and resist soldering temperatures up to 250 deg C for 30 seconds. Applications for SMRF 1812 inductors include RF signal circuitry in communications, test & measurement, medical diagnostic, and industrial process control... Read More

Electronic Components & Devices

Microwave Preamp covers wide bandwidth.

Apr 18, 2002

LN1G11 Low Noise preamp covers bandwidth of 1.0 to 11.0 GHz, has minimum gain of 27dB, and is suitable for amplifying low-level signals to drive power amplifiers. With its low noise, it can also be used to increase sensitivity of EMC receivers that have relatively high noise figures. It comes with benchtop cabinet and front or rear connectors. Other preamplifiers are available with frequencies... Read More

Electrical Equipment & Systems, Electronic Components & Devices

LED Driver can power three at a time.

Apr 18, 2002

S-8813 Series three-channel white LED driver IC can power up to 3 LEDs. S-881300OBPE-TB allows user to vary output current linearly between 5 and 18 mA by changing voltage supplied to current set pin (VISET). S-881300CPE-TB allows user to set output current between 5 and 18 mA by connecting resistor to current set pin (RISET). Ultra-small SON10 package and constant-current output make series... Read More

Electronic Components & Devices

Connector eliminates bent pins.

Apr 18, 2002

Power-Edge(TM) PEC Series has edge card interface with 3, 7 or 10 contacts. One-piece interface is rated up to 5 A and has contacts on .100 in. pitch. Built-in card latches increase withdrawal force required for removing power board. Optional alignment pins and locking clips can be provided. Read More

Computer Hardware & Peripherals, Electronic Components & Devices

USB Receptacle saves space on printed circuit boards.

Apr 17, 2002

Upright, right-angle, A-type USB connector reduces footprint by 25% compared to previous products. Connector allows high-speed data transfer between computers and peripherals such as printers, scanners, and video equipment. It has kinked grounding pins for PC retention, and indentations at inlet for mating retention. Height is 0.545 in. Insulator material is black or white, PBT thermoplastic and... Read More

Electronic Components & Devices

Terminal Blocks provide alternative connections.

Apr 17, 2002

253 Series printed circuit board terminal blocks have 2 push wire connections: one parallel to PCB and one perpendicular. Alternative connection allows electrical potential to be looped without additional terminal blocks. Solid conductors with cross section from 20 to 16 AWG can be connected. Series is rated at 500V, and carries load current of 10A. Pin spacing is 5 mm. Read More

Controls & Controllers, Electronic Components & Devices

Power Controller is PCI hot-plug compliant.

Apr 17, 2002

MIC2590 dual-slot controller supports system voltages required by PCI, including 3.3 V auxiliary voltage specified by PCI Standard v2.2. It supports +12, -12, 3.3, 5.0 V primary supplies, and 3.3 V auxiliary supplies with overcurrent protection. IC offers adjustable overcurrent timeout, circuit-breaker fault protection, and undervoltage lockout. Integrated 8-bit ADC monitors voltage and current... Read More

Electrical Equipment & Systems, Electronic Components & Devices, Mounting & Attaching Products

Coaxial Connector will not vibrate loose.

Apr 17, 2002

Series 1.0/2.3 coaxial connector interface delivers RF performance in switching equipment operating at frequencies up to 4 GHz. Its push-pull coupling mechanism allows installation and de-coupling, and will not accidentally disconnect. These 50 ohm connectors have working voltage ratings of 250 Vrms and dielectric withstanding voltage rating of 750 Vrms. Straight and right angle connectors have... Read More

Electronic Components & Devices

Photodiode suits IrDA transceivers.

Apr 17, 2002

Model SD150-13-003 4 Mbps silicon PIN photodiode, tailored for OEM optical communications for IrDA-compatible transceivers, also suits fiber-optic LANs, and VCSEL-based IR links. Rise and fall times are optimized for digital transmission, while signal tailing is largely eliminated. Unpackaged chip has active area of 1.4 sq mm. Custom versions are available to to suit specific OEM requirements.... Read More

Electronic Components & Devices, Test & Measuring Instruments

Signal Conditioners handle hundreds of I/O combinations.

Apr 17, 2002

WAVEANALOG is available in three models, all providing 0 to 10 Vdc, 0 to 20 mA, or 4 to 20 mA output signals. Pro DC-DC takes inputs between 20 mV to 200 Vac bipolar for voltage and 0.1 to 100 mA bipolar for current. Pro RTD field configurable signal conditioner takes PT100/2/3/4-wire RTDs, Ni 100, and potentiometer inputs. Pro Thermo takes thermocouple types K, J, T, E, N, R, S, and B inputs.... Read More

Electronic Components & Devices

Electrolytic Capacitor has extended cathode foil.

Apr 17, 2002

Aluminum Type 4CMC capacitor ranges in capacitance up to 420,000 microF at 16 V, 14,000 microF at 200 V and 2,300 microF at 500 V. It has three 0.062 in. diameters, solid copper mounting pins for reverse-proof mounting, and case sizes from 1.375 x 1.75 to 2 x 5.75 in. Type 4CMC replaces large snap-in or screw-terminal capacitors. Unit handles up to 50 amps of ripple current and is suitable for... Read More

Controls & Controllers, Electronic Components & Devices, Mechanical Power Transmission

Motor Drive ICs cool fan motors.

Apr 16, 2002

FAN8404D and FAN8408D are 2-phase, half wave motor drive ICs capable of sinking 1.2 A motor load current, while requiring 2.2 mA supply current in stand-by. FAN8408D features Hall output (HO) for motor speed detection and FAN8404D offers alarm output to signal fan lockup. Operating voltages range from 4 to 15 V. Units include built-in thermal shutdown (TSD) circuits, reverse-current protection... Read More

Electronic Components & Devices, Mounting & Attaching Products

USB A Connector can connect multiple peripheral devices.

Apr 16, 2002

Type AJT03G stacked USB port can connect up to 127 peripheral devices such as mice, modems, and keyboards. USB also supports Plug-and-Play installation and hot plugging. Read More

Electronic Components & Devices

Switching Regulators provide small footprint.

Apr 12, 2002

S-835X Series of PWM and PWM/PFM CMOS switching regulators consist of reference voltage source, oscillation circuit, error amplifier, phase compensation circuit, PWM control Circuit (S-8355/57) and PVWM/FM switching control circuit (S-8356/58). Oscillation frequencies of 100, 250, and 300 kHz are available. Regulators have low operation current consumption of 25.9 microA (3.3 V, 100 kHz). SNB6B... Read More

Display & Presentation Equipment, Electrical Equipment & Systems, Electronic Components & Devices, Vision Systems

Bargraph LEDs are visible in sunlight.

Apr 12, 2002

Solid-state Linear Bargraph LEDs have average life span of 100,000+ hours. Standard intensity LEDs, with 565 to 660 nm at 20 mA, come in Ultra-Red, High-Efficiency Red, Yellow, and High-Efficiency Green. Super Intensity LEDs, with 523 to 330 nm at 20 mA, are available in Super Orange, Super Yellow, and Aqua Green. LEDs are suitable for aviation instrument panels, temperature gauges, automotive... Read More