Right Angle Connector suits shallow wiring applications.
Using 6 in. stranded or solid pre-stripped wires, polycarbonate PlugTail(TM) Connector provides right angle crimped and welded contacts, so wire leaves housing at 90Ã-
Read More »InfiniBand Adapters suit Intel-based clusters.
Expanding support to IntelÃ-® XeonÃ-® single-core and dual-core architectures, InfiniPath(TM) InfiniBand(TM) Adapters optimize data throughput on PCI ExpressÃ-®-based systems by eliminating bottlenecks that can slow down communications. Combining pipelined, cut-through design with direct hardware support for multi-core processors in connection-less software environment, HyperMessaging...
Read More »
Stud Boxes are usable with -½ or 5/8 in. wallboard.
Classified for 2-hour wall and ceiling fire resistance, 22.5 cubic in. Horizontal Steel and Wood Stud Boxes accept eleven #14, ten #12, and nine #10 wires. Bracket countersink allows for mounting with #8 wafer head or dry wall screws. Side and leg stabilizers ensure device rigidity, while Height Site alignment guide and box levelers center box and device at right angle with stud. Boxes...
Read More »ZIF Connectors minimize signal crosstalk.
With minimum rated life of 10,000 mate/unmate cycles and no loss in performance, DLP Series Zero Insertion Force Connectors can be mated/unmated in less than 2 sec. Because contact in receptacle connector mates directly to PCB on plug half, signal paths are minimized. Connectors use 34-way high-density contact modules and are available in 136, 204, 272, and 408 configurations. Rated current is...
Read More »
EMI Filters 101: Everything You Need To Know
In this eBook, we'll discuss everything you need to know about EMI filters, including their importance, regulatory requirements, and different types.
Read More »Filter Connector withstands thermal shock and vibration.
Featuring Canon CoF technology, filter connector provides standard filtering capabilities including individual isolated pin filtering of high-frequency noise, built-in ground plane barriers in the connector inserts, and filtering at face of system boxes. In MIL-DTL-38999 configurations, it meets MIL-STD and MIL-DTL Series III standard for thermal shock, random vibration, humidity, and high...
Read More »NEC and NEC Electronics Introduce New 45nm-node LSI Interconnect Technology for Reliability and Low-Power Consumption
Quality Improvement of Next-Generation ULSI Based on Molecular/Atomic-Level Structure-Control Technology TOKYO, Dec. 6 / -- NEC Corporation and NEC Electronics Corporation today announced they have developed a 45-nanometer (nm) node LSI interconnect technology that addresses both reliability and low- power consumption. The achievements are based on the reliability improvement by a...
Read More »NEC Electronics and NEC Corporation Announce Design Sequence to Optimize Multi-Level Interconnects for Applications Using 45-Nanometer CMOS Process Technology
TOKYO, Dec. 6 / -- NEC Electronics Corporation and NEC Corporation today announced the development of an application specific interconnect structure (ASIS) that enables fine tuning of the multi-layer interconnect structure for the various applications in 45 nanometer (nm) CMOS process generation. The companies also verified that by using this technology, the optimal interconnect structure can be...
Read More »Switch integrates RapidIO-® in ATCA/MicroTCA architectures.
Based on Serial RapidIO Specification v1.3, Model Tsi578(TM) interconnects Serial RapidIO-enabled processors and peripheral devices, supporting aggregate bandwidth of 80 Gbits/s. It provides up to eight 4x mode ports or sixteen 1x mode ports, each configurable to 1.25, 2.5, or 3.125 Gbit/s. Switch can route packets to over 64,000 endpoints, independent unicast and multicast routing mechanisms,...
Read More »RFAC Solutions Has Launched a RF Connector Series
RFAC Solutions, Inc. is a premium quality manufacturer of RF connector, cable assembly, attenuator, filter, amplifier, and switch in microwave spectrum applications ranging from wireless communications infrastructure to consumer product production. We take much pride in our manufacturing capability, on-going product development, and offering of RF parts based on the high quality assurance (ISO...
Read More »Push-Pull Connectors operate in temp range of -40 to +100-
Amphe-PPM series of push-pull aluminum shell connectors enable quick mating and unmating of signal and power interconnects in medical electromechanical instrumentation and process control applications. Non-sealed connectors are offered in 12 or 16 mm housings with 2-12 contacts 1.0-2.5 mm in dia, and rear accessory can be either rubber boot or cable clamp. Sealed connectors are available in 10,...
Read More »
Precision Machining Solutions with Over 25 Years of Experience
Quality, customer service, and unbeatable value are the hallmarks of Hogge Precision. Since 1989 we have built a reputation as the go-to precision machining source, servicing many demanding industries. For CNC machining and screw machining, there are few manufacturers that can match our capabilities and expertise. See our video to learn more.
Read More »
