Larson Electronics, LLC    Kemp, TX 75143
Nov 18, 2011 Designed for portability and safe operation in Class 1 Div 2 hazardous locations, Model EPL-PM-1X400MH-100 produces 36,000 lumens, illuminating up to 25,000 ft² of workspace. Lamp has cast aluminum weatherproof housing and heat- and impact-resistant tempered flat glass door that is hinged for re-lamping. Flat pedestal base provides stable platform, while trunnion bracket allows lamp to be adjusted vertically as needed. Supplied with 100 ft SOOW cord, lamp operates from 120-277 Vac.

NK Technologies    Campbell, CA 95008
Nov 18, 2011 Featuring 1 in. housing with ring design, AS1 Series-CC slips onto conductor to detect currents as low as 0.5 A with single conductor pass. Powered directly from monitored circuit, switch monitors and reports electric motor load status, identifies open heater circuit connections, and verifies that load is energized. Contact can control AC or DC circuits to 120 V, with max load capacity of 150 mA. With solid-state output and no moving parts, switch provides nearly unlimited operations.

Specialized Products Company    Southlake, TX 76092
Nov 18, 2011 QuadLink turns any 6 or 12 Vdc battery charger into 4-station maintenance charger, automatically splitting and distributing all of the charger's capabilities into 10-minute sequencing charge segments. Four-way switcher is capable of charging batteries individually connected or connected as group in 24, 36 or 48 volt series. Output cable length is 5 ft 9 in., and 5 and 25 ft long cables are also available.

Cummins Power Generation Americas    Minneapolis, MN 55432
Nov 18, 2011 Incorporating 95 L QSK95 engine, C3000 Series meets EPA Tier 4 Final emissions taking effect in 2015. Selective Catalytic Reduction (SCR) after treatment system is intended to replace exhaust muffler on genset, offering flexible packaging solution. Able to be used anywhere in world for standby, prime, or continuous duty applications, genset offers performance - fuel consumption, transient response, emissions reduction - that can be optimized among to accommodate different applications.

ZMDI    Dresden 01109  Germany
Nov 17, 2011 Supplied in QFN32 5x5 package with 0.85 mm profile, AECQ100-qualified ZSSC1856 is used for measuring vehicle battery state of health/charge/function. Internal 18-bit Sigma/Delta ADC with on-chip voltage reference features 2 input channels for measuring IBAT via voltage drop at external shunt resistor as well as VBAT and temperature. Along with built-in self-test and diagnostics, IC features calibrated on-chip temperature sensor. Measurement cycles and wakeup conditions are user controlled.

CUI, Inc.    Beaverton, OR 97005
Nov 17, 2011 Measuring 2.0 x 1.0 x 0.6 in. in 5 W package, board mount VSK Series provides continuous output power, universal input from 85-264 Vac, and fully regulated DC outputs of 3.3, 5, 9, 12, 15, 24, and 48 Vdc. Modules offer 4 KVac isolation in 5 and 10 W versions and 3 KVac isolation in 15, 20, and 25 W versions. With 87% efficiency and operating temperature of -25 to 70°C, isolated AC-DC modules are suited for low power ITE, industrial, and consumer electronics applications.

Tripp Lite    Chicago, IL 60609
Nov 17, 2011 Available in 3, 5, and 10 ft lengths with 550 MHz Gigabit speed rating, Catetory 6 Cables feature 90° angled connectors in up, down, right, and left configurations. Units are suitable for connection in areas where space is limited, such as networking racks, behind desks, or at wall connections.

Larson Electronics, LLC    Kemp, TX 75143
Nov 17, 2011 Fitted with 200 lb grip magnetic base and double ball joint arm, Model LEDLB-12ET-DBM-I mounts on any ferrous metallic surface and can be adjusted through 360° of rotation and 140° of tilt. U-shaped trunnion bracket provides additional 270° of vertical adjustment. Constructed with extruded aluminum housing and impact-resistant polycarbonate lens, 36 W LED light bar produces over 2,000 lumens and is IP68-rated waterproof to 3 m. Inline transformer allows connection to 110-120 Vac power sources.

Larson Electronics, LLC    Kemp, TX 75143
Nov 17, 2011 ETL-approved for use in wet locations, LEDWP-400 incorporates light assembly containing twelve 3.33 W LEDs that have 50,000 hr life expectancy and are matched with special reflector to produce light output that compares to that of 400 W metal halide units. Waterproof and powder coated aluminum housing, polycarbonate lens, solid state design, and lack of ballast provide durability and reliability, while stainless steel mounting hardware allows 380°/180° rotational adjustment.

GE Co.    Southfield, MI 48034
Nov 17, 2011 Performing energy measurements accurate to within 0.2%, Multilin EPM 7000 is intended for applications requiring revenue metering, such as billing. Event and disturbance recording feature enables users to analyze power quality events over long periods of time, while historical data recording and logging capability lets customers retrieve archived data, capture past events, and analyze disturbances. Multiple communication ports are available for integration with DCS and SCADA systems.

Infinite Power Solutions    Littleton, CO 80127
Nov 17, 2011 Comprised of micro-energy cells (MECs), THINERGY MEC200-Series has self-discharge rate of ~3 nA that lends to near loss-less 4.1 V energy storage solution with capacities of 0.13, 0.4, and 1.0 mAh. In addition to flex circuit encapsulation and short circuit protection, MECs feature positive and negative terminals that are on same edge of cell to accommodate stacking and solder to rigid or flex PCB. When recharged over lifetime, 0.17 mm thin MECs provide tens of watt-hours of energy.

Power Sources Unlimited, Inc.    Wrentham, MA 02093-2210
Nov 15, 2011 Supplied in metal case with screw terminal connection, Traco Power TEP 150WI series operates from -40 to +75°C and carries UL/cUL safety approvals to EN60950-1. Input filter module is designed to meet EMC demands, such as conducted noise, in accordance to EN55022 class B as well as burst and surge immunity without external components. Available with 9-36 Vdc and 18-75 Vdc input ranges, series offers outputs of 12, 15, 24, 28, and 48 Vdc @ 12.5, 10, 6.3, 5.4, and 3.2 A, respectively.

Micro Analog Systems Oy    Helsinki   Finland
Nov 15, 2011 Available in 6-pin, 3 x 3 x 0.75 mm QFN package, MAS6011 monitors supply voltage and charging of battery-powered system containing one small solar cell. Current consumption is 110 nA, enabling system to charge from low light conditions and stay in power down mode for years yet still operate directly from battery before recharging. Targeted for solar powered wireless modules, IC supports switching levels designed for usage with rechargeable 3 V Lithium Vanadium batteries.

Semiconductor Circuits, Inc.    Atkinson, NH 03811
Nov 15, 2011 Supplied in 2.60 x 0.8 x 0.365 in. pacakage, FLEX-4 Cool Power Technologies 7-15 V converter allows for up to 60 A of combined output current. Additional fifth output is programmable to 5 or 3.3 V and up to 50 mA output current. Output startup/shutdown delay and ramp time allow fully programmable sequencing, and 2 GPIOs can be programmed to indicate power good or fault conditions or used as inputs to enable outputs as required. Efficiencies exceed 90% from half through full load.

Itt Corp    San Jose, CA 95110
Nov 15, 2011 Featuring canted spring technology, which provides full 360° EMI protection, Nemesis Series Space Saver Connector offers blind mating and snap-on/rip-away coupling to prevent military personnel from being endangered should cable snag. Ribbed over-molding provides secure grip under difficult conditions. Operating from -40 to +100°C, connector features max current rating of 2 A, voltage rating of 50 Vdc, and minimum insulation resistance of 500 MW.

Larson Electronics, LLC    Kemp, TX 75143
Nov 15, 2011 With ability to convert 480 Vac 3-phase current to single-phase 120/208Y AC configuration, Model MGPD-SP-200-1D-45-2B allows operators to utilize generators or outside high voltage power sources when local or native power sources are unavailable. Portable 45 KVA unit makes 240 Vac available via two 100 A breakers for uninterrupted flow of usable power. Safe operation is achieved through inclusion of fusible NEMA-3R disconnect and 60 A fuses for positive power control and overload protection.

Analog Modules, Inc.    Longwood, FL 32750
Nov 15, 2011 Requiring +5 Vdc, Model 784 CW and Pulsed Laser Diode Driver offers variable pulse widths from 600 ns to CW and power capabilities up to 125 W with adequate cooling. RoHS-compliant unit features max current output of 5 A and compliance voltage to 2.5 V. Measuring 3.69 x 3.05 x 0.87 in., driver includes current limit and thermal shutdown protection. Device is suited for high current single laser diode pumping and direct illumination.

Columbia Lighting    Greenville, SC 29607
Nov 15, 2011 Employing solid-state electronics, eopoc® LED has full distribution design and is tuned to maintain color consistency within each fixture, from fixture to fixture, and throughout operational lifetime. Hinged optical system and plug-and-play LED modules facilitate service, and 2 lumen output configurations are available. Each luminaire employs 50,000 hr, mercury-free lamp; is constructed from 70% recycled steel; and works with such controls as occupancy sensors and dimmers.

C&K Components    Newton, MA 02458
Nov 14, 2011 Equipped with infrared LED and phototransistor to precisely detect control signal, Model RB-4G0124 provides electrical life of 1,000,000 cycles and mechanical life of 20,000,000 cycles. Model RB-231, featuring shielded design that provides 10° angle of detection, provides operating life of 100,000 cycles. Conductive ball is movable inside tube to generate signal and contact. Both are suited for movement detection, safety devices, and consumer electronic applications.

Electro Standards Laboratories    Cranston, RI 02921 3403
Nov 14, 2011 Transparent to data speed and format, Model 8581 facilitates switching of 2 inputs to 3 outputs for access to shared channel, backup data line, or peripheral by turning one knob. Sealed switch with self-wiping low impedance contacts can be custom modified to connect 2 In ports, A and B, to Out ports 1, 2, and 3 in various configurations. Custom switch position labeling and custom wiring is optionally available to accommodate specific network requirements.