Aremco Products, Inc.    Valley Cottage, NY 10989
Dec 09, 2011 Consisting of single part, water-based, inorganic-ceramic coating system, Cerama-Dip(TM) 538N electrically isolates high-power ceramic resistors for applications up to 2,600°F. Odorless, VOC-free formula features volume resistivity of 109 W-cm and dielectric strength of 225 V/mil at room temperature. Applied by dipping or brushing, Cerama-Dip 538N cures by air-drying at room temperature for 1-2 hr, then step curing for 1-2 hr at 200°F and 350°F, respectively.

MaxLite    West Caldwell, NJ 07006
Dec 09, 2011 Suited for remodeling or new construction projects, 14 W Dimmable LED 6 in. Recessed Downlight Retrofit can replace 65 W BR40 incandescent lamps in recessed fixtures. Unit is engineered with chip array featuring ceramic LED technology, guaranteeing single bin color consistency with optimal illumination uniformity and minimal glare. Constructed without any hazardous materials, downlight turns on instantly from cold start without flickering and features CRI greater than 80.

ITT Interconnect Solutions    Santa Ana, CA 92705
Dec 09, 2011 Featuring 24-spring probe and pad contact technology, Filter Spring Probe Series extends operating life of in-the-field military equipment. Technology creates electrical contact by utilizing pressure-point force on spring-loaded pin to contact pad, instead of sliding forces found on conventional pin socket contacts. Flush with mating face of connector, contact pad on receptacle side of connector can be cleaned by wiping interface, making interconnect suited for field applications.

Electro Standards Laboratories    Cranston, RI 02921 3403
Dec 09, 2011 Certified for Cat6A compliance, Model 7371 utilizes shielded RJ45 connectors and provides 3 positions of A/B/C switching. Single-channel unit switches all 8 pins of RJ45 interface and is transparent to data speed and format. Switch position can be controlled manually via front panel pushbutton or remotely via ASCII RS232 Serial Data commands. Remote control port allows off-site monitoring and management including ability to lockout front-panel pushbutton control.

Agilent Technologies, Inc.    Santa Clara, CA 95051
Dec 09, 2011 Capable of delivering up to 375 W to multiple devices or points, U8030 Series is suited for margin tests, burn-in or reliability tests, and general electronics manufacturing. Intuitive user interface enables all 3 channels to be controlled individually or simultaneously with press of button. To help users observe total power drawn by device-under-test, power supplies include screen that displays voltage and current readings.

Electro Standards Laboratories    Cranston, RI 02921 3403
Dec 09, 2011 Model 7295 allows 2 pairs of compatible devices to exchange interconnections by supporting connections between 4 devices or peripherals connected to ports A/B/C/D in 2 different positions: Normal and Crossover. Transparent to data speed and format, product switches all 25 pins of DB25 interface. Front panel pushbutton affords manual position control, while contact closure transition signals enable remote off-site monitoring, front panel pushbutton lockout, and position control.

Weidmuller, Inc.    Richmond, VA 23236
Dec 08, 2011 Available in 8 single- and dual-channel models, ACT20M Series features 2-channel loop-powered isolation, signal splitting with power provided for transmitter, or universal input conversion. DIN-rail mountable, 6 mm wide modules offer option to distribute power through rail, minimizing wiring. With isolation level of 2.5 kV, less than 0.05% accuracy, and ambient temperature range of -13 to 158°F, ACT20M Series is suited for industrial process measurement and control applications.

Larson Electronics, LLC    Kemp, TX 75143
Dec 08, 2011 In addition to wheeled tripod with no-flat rubber wheels, WALTP-2XWP400MCE has dual 50,000 hr-rated LED light heads that, operated independently or together, produce illumination comparable to 250 W metal halide lamp. Extendable tripod tower, constructed of heavy-duty aluminum and coated with corrosion-resistant finish, allows light heads to be extended 7-13 ft high. Additional features include powder coated aluminum housings and unbreakable polycarbonate lenses.

Bridgeport Fittings, Inc.    Stratford, CT 06497
Dec 08, 2011 Available in straight, 90°, and U-shaped strap-type duplex SG3838ASP versions, Whipper-Snap® Connectors for AC/MC and MCI-A cable are snap-in fittings that save time and labor with their quick-install design, are easy to remove, and are reusable. Various single and duplex configurations are available to meet diverse application requirements.

Eastex Products, Inc.    Holbrook, MA 02343
Dec 07, 2011 Made from Nylon with micro hook on one side and low-profile loop on other, Eastex Strap-It(TM) Cable Wrap is used for organizing and bundling optical fiber cabling that might be damaged from rigidity and over-tightening of plastic cable ties. Adjustable and reusable product, which can be quickly opened/closed hundreds of times and cut to length if necessary, comes in ½, ¾, and 1 in. wide sizes and is supplied on 25 yd rolls.

Electrotech Sales Group, LLC.    Colmar, PA 18915
Dec 07, 2011 Assembled in USA, 120 Vac DIN rail mounted duplex receptacle outlet box provides power source in control cabinet for laptops, test equipment, lighting, and more. Product is offered in 15 or 20 A versions, both of which have external terminal block connections to facilitate wiring and are equipped with metal spring clip for secure fasting to DIN 35 mm rail. Additionally, 15 A GFCI duplex receptacle outlet box is available.

Larson Electronics, LLC    Kemp, TX 75143
Dec 07, 2011 Powered by 14.3 V lithium poly battery and recharged via included 15 x 13 in. solar panel, SPLED-CL1B-M can run for 5+ hr on full charge and is mounted securely via single 100 lb grip magnet fitted into base. Unit offers 30 strobing flash patterns, allowing users to tailor operation to application requirements. Suited for use where normal power sources are unavailable, beacon is connected to solar panel and battery assembly via 20 ft of cord to allow for optimal placement.

Dwyer Instruments, Inc.    Michigan City, IN 46361
Dec 07, 2011 Providing both low and high limit control, Series AT23000MR and AT23000MRS Photohelic® Switches/Gauges combine differential pressure switch with analog pressure gage. AT23000MR Series employs electromechanical relays, while AT23000MRS Series uses SPST (NO) solid state relays. Compatible with air and other non-combustible, non-corrosive gases, gauges handle pressures to 25 psig. Flame-proof ATEX enclosures have glass window for viewing set point needles and process pressure.

Caltron Industries, Inc.    Fremont, CA 94538
Dec 07, 2011 Suited for integration into enclosure, 19 in. Model LBT-1904O features 376.32 x 301.06 mm active area, 1,280 x 1,024 max resolution, 16 million display colors, and contrast ratio of 1,000:1. Monitor operates from 32-122°F and includes standard 15-pin VGA input connector. Suited for instrumentation panel displays, kiosks, and photo booths, monitor is available with resistive or surface acoustic wave touch option as well as serial or USB touch interface.

Amerlux, Inc.    Fairfield, NJ 07004
Dec 06, 2011 Along with LED module and built-in speaker, SmartSite(TM) Street Lights feature duo-band radio system and miniature computer with data storage capacity. Street light processors communicate with each other through bi-directional wireless mesh network and monitor individual luminaire usage, energy costs, grid power, and system integrity. Luminaires also offer multimedia solutions that can upgrade existing infrastructure to provide information, advertising, security and entertainment for public spaces.

Calex Mfg. Co., Inc.    Concord, CA 94520
Dec 06, 2011 Featuring continuous input range of 9-75 Vdc, AHW Series provides regulated ±5, ±12, and ±15 Vdc output at ±400, ±167, and ±133 mA. Open frame converters utilize solder ball pins for surface mount installation and can fully regulate down to no-load condition. Measuring 1.22 x 0.78 x 0.28 in., units operate from -55 to +100°C, provide input to output isolation of 1,544 Vdc, and can withstand aggressive solvents and cleaning cycles during manufacturing process.

Columbia Lighting    Greenville, SC 29607
Dec 06, 2011 Part of createchange® series, Serrano Luminaire features 3-element diffuser that combines performance-optimized center optic with 2 lenticular side lenses to provide batwing distribution. Two center lens options are available to customize aesthetic. Operating with variety of controls, luminaire has hinged optical system that offers tool-less, below-ceiling access to lamps and ballast. The wiHUBB enabled option permits seamless integration with Hubbell Building Automation's wireless mesh network.

EAO Switch Corp.    Milford, CT 06460
Dec 06, 2011 Designed to alert users to system malfunction from any angle, Series 56 Flashers can be illuminated in range of LED colors, including red, green, blue, yellow, and orange. Front ring can be chrome or plastic and is also offered in various colors. Environmentally sealed to IP67 at front and IP65 at rear, pushbuttons operate in extreme conditions ranging from -49 to +176°F. Applications include public transportation, public lifts and elevators, and roadside emergency telephones.

TDK-Lambda Americas Inc.    San Diego, CA 92154
Dec 06, 2011 Supplied in 2 x 4 x 1 in. package and rated to 65 W, convection-cooled MWS65 series operates from universal 90-265 Vac input and includes 5 models with nominal outputs of 5, 12, 15, 24, or 48 Vdc. All outputs are user-adjustable by ±10%, and flat efficiency curve reaches up to 89% from 20-100% load. Consuming less than 0.3 W power under no-load conditions, series offers 4 kVac reinforced input to output isolation and 1,500 Vac output to ground isolation.

CW Industries    Southampton, PA 18966
Dec 05, 2011 Rated 8 A at 250 Vac, Series GRS-4021 is made of heavy-duty nylon with copper alloy terminals and male .187 in. wide quick connect terminal. Switch can be mounted in .756 x .508 in. panel opening with no screws or other fasteners required. Available in DPST construction, RoHS-compliant device complies with 850°C Glow-Wire Test for insulating material used in construction. Switch is suited for main power disconnecting in appliance, lawn and garden, floor care, and medical markets.