ITW Ransburg Electrostatic Systems
Toledo, OH 43612
Aug 25, 2005 Used in single- or multiple-component applications, RCS 2 is suited for precise electronically controlled gear-pump metering and mixing. It features magnetically coupled metering pumps that eliminate shaft seal leaks and provides absolute on-ratio gear-driven 1, 2, or 3 k mixing and metering control. In addition to solventborne or waterborne materials, system can also be used with rotary atomizers, bells, disks, and electrostatic or non-electrostatic guns.

Entegris Semiconductor
Chaska, MN 55318 2342
Jul 19, 2005 Model NT® Integrated Flow Controller helps semiconductor equipment makers enable chemical handling and blending as close to point of use as possible. DeviceNetâ„¢ communications protocol delivers diagnostics for monitoring, trouble-shooting, and problem-solving, helping to keep fabs up and running.

Advanced Energy Industries Inc.
Fort Collins, CO 80525
Jul 15, 2005 Featuring multi-gas, multi-range functionality, Aera® PI-980â„¢ series helps improve processes for etch, CVD, PVD, and diffusion in semiconductor applications. Mass flow controller (MFC) promotes gas-flow stability and provides real-time process control. Combining NeuralStepâ„¢ control technology with integrated pressure transducer, series increases speed of MFC response, eliminating effects of upstream and downstream pressure disturbances.

Siemens Building Technologies, Inc.
Buffalo Grove, IL 60089
Apr 29, 2005 TALON Predator Single Duct/Dual Duct Low Flow Controller is suited for flow ranges between 150–1,200 fpm, with tightest accuracy below 400 fpm. It provides quiet operation to eliminate occupant white noise. Variable air volume controller is suited for critical environments in hospitals, laboratories, industrial buildings, and medical offices where highly accurate building control is required.

Cole-Parmer Instrument Co.
Vernon Hills, IL 60061
Apr 27, 2005 Universal Mass Flow Control System allows user to monitor 4 flowmeters or flow controllers from anywhere Internet-connected PC is available. Each flowmeter channel features totalizer and dedicated alarm, and there are 2 dedicated relay outputs per controller. Batch control program allows execution of up to 16 steps in batch process, while flow control program directs flow control through user-defined series of up to 96 steps, ramping flow rates up, down, on, or off.

Cole Parmer Instrument Co.
Vernon Hills, IL 60061
Feb 16, 2005 Universal Module allows users to monitor up to 4 flowmeters or flow controllers from anywhere with Internet-connected PC. Controllers are connected using 0–5 Vdc output. Batch control program allows for execution of up to 16 steps in batch process, while flow control program directs flow control through user-defined series of up to 96 steps. All features can be programmed through integrated keypad or optional RS-232 or HTML/TelNet interfaces.

CONCOA
Virginia Beach, VA 23454
Dec 03, 2004 IntelliSwitchâ„¢ electronic gas delivery system features smart operation for universal input compatibility. Microprocessor-controlled automatic switchover system incorporates software technology for selection of most efficient gas mode and reduction of residual gas returns. Push of one button allows for interchangeable service from high-pressure cylinders to cryogenic liquid cans. Product records data, enabling user to monitor process activity from remote sources.

ITW Ransburg Electrostatic Systems
Toledo, OH 43612
Sep 10, 2004 Utilizing closed-loop module, AirTronic provides continuous, precise monitoring and control of air volume set points for rotary atomizers, air atomizers, and powder pumps. It accommodates independent and slave modes by incorporating 2 channels per module and 2 modes of operation. AirTronic provides production monitoring through standard lpm display units at module or remote location. It offers fault detection via warning codes on LED display.

Siemens Building Technologies Inc.
Florham Park, NJ 07932
Aug 02, 2004 TALON® Predator® Variable Air Volume controller features thermal control sequence that automatically adjusts air flow to maintain cooling as supply air temperature changes. It facilitates DX cooling zone control by eliminating room temperature disturbance due to frequent cycling of DX systems. Varying supply temperature causes adjustment of air flow rate in response to supply temperature as well as to room temperature.

Laboratory Control Systems, Inc.
Scranton, PA 18508
Jul 19, 2004 With 25 µsec scan rate, 1 Mb Flash memory, and 1 Mb RAM, microprocessor-based Envirotrak® IV controls equipment and processes used to maintain room temperature, pressure, humidity, airflow, or any combination of the above. It supports BACnet, Modbus, LonWorks, and N2 protocols and incorporates up to 48 I/O control points. Product may be programmed to scan each individual point in any sequence without imposing limits on application or number of downloadable graphic programs.

Novar Controls Corp.
Copley, OH 44321
Jun 10, 2004 VAV-4040 Variable Air Volume/Variable Volume and Temperature Controller utilizes Belimo® damper actuator. VVT mode allows damper output to reverse its action in response to supplied air temperature. Module features on-board differential pressure airflow sensor, air quality compensation/ventilation override, and pressure-independent/dependent control. It also provides staged reheat control and tri-state or 2–10 Vdc modulating reheat control.

Advanced Energy Industries Inc.
Fort Collins, CO 80525
Apr 12, 2004 Area® Transformerâ„¢ digital, multi-gas, multi-range MFCs provide field programmability to run any gas for any gas flow range from 10 sccm to 30 slm. As few as 8 different models can be used to support fab's requirements. Units allow unlimited gas selection without recalibration and can be pulled directly from customer's inventory shelf and programmed to meet requirements.

Emerson Process Management, Intellution Division
St. Louis, MO 63136 8506
Mar 26, 2004 Capable of controlling liquids and gases, Brooks Instrument QUANTIM Coriolis meter and controller utilizes modular hardware platform using sensing tube geometries and optical sensing techniques. Modular hardware platform allows product to measure and control flows from 1–28,000 g/hr. Equipped with integrated sensor, transmitter, valve, and control electronics, unit allows users to control liquids or gases without switching meters or recalibrating device.

Kaeser Compressors, Inc.
Fredericksburg, VA 22404
Mar 12, 2004 Sigma Air Manager combines benefits of industrial PC with integrated Internet capabilities for compressed air system monitoring and control. Master controller maintains consistent pressure band control and provides tools to manage any system in real-time. With in-depth air demand analysis, air system data is available from any location through HTML reports. Controller, capable of managing 3–16 machines, monitors, sequences, and analyzes air system performance.

Parker Hannifin Corp., Brass Products Div.
Otsego, MI 49078 1472
Dec 02, 2003 Flow Control Regulators mount directly on air cylinder and come in meter out versions. Adjustment screw provides precise airflow control, and locking nut resists effects of vibration. Regulators are offered with NPT threads and push-to-connect fittings or NPT threaded ports. All have solid brass body treated for chemical resistance, SS tube gripping ring, and nickel-plated brass adjustment screw. Working pressure is 15–145 psig and working temperature is 30–160°F.

Parker Hannifin Corp., Pneumatic Div.
Richland, MI 49083 0901
Dec 02, 2003 Miniature Flow Control Regulators control speed of small-bore cylinders such as pancake/flat types. Fine adjustment screw allows precise settings, while lock nut ensures that settings are maintained. Units have push-to-connect tube ends with NPT threads. All feature glass-reinforced nylon composite body, SS tube gripping ring, and nickel-plated brass adjustment screw. Working pressure is 15-145 psig, and working temperature is 30-160°F.

Parker Hannifin Corp., Brass Products Div.
Otsego, MI 49078 1472
Dec 02, 2003 Meter out versions of Miniature and Compact Flow Control Regulators allow vertical or angle tube exit where access is restricted. Fine adjustment screw and locking nut provide precise, maintainable settings. Mounting directly on air cylinder, compact versions measure 2 in. high at full extension and are offered with fractional inch push-to-connect ends and NPT or UNF threads; Miniature versions measure 1 in. All regulators feature working pressure from 15–145 psig.

Parker Hannifin Corp., Brass Products Div.
Otsego, MI 49078 1472
Nov 25, 2003 In-Line Flow Control Regulators are unidirectional flow control valves with female NPT threads that allow them to be spliced into air cylinder port line. Construction includes glass reinforced nylon composite body, stainless steel tube gripping ring, and adjustment screw components of nickel-plated brass. Available with working pressures from 15–145 psig, units may be installed as meter in or meter out with full flow in both directions.

Parker Hannifin Corp., Brass Products Div.
Otsego, MI 49078 1472
Nov 25, 2003 Flow Control Regulators are available with raised fine adjustment screw and locking nut or recessed, knobless adjustment screw. Both are offered in meter out versions to provide precise airflow control and speed regulation of pneumatic cylinder. Units are available in various sizes for fractional inch tube to NPT threads for mounting directly to cylinder. Working pressure ranges from 15–145 psig, and body material is glass reinforced nylon composite.

Parker Hannifin Corp., Pneumatic Div.
Richland, MI 49083 0901
Nov 20, 2003 Offered with balanced poppet/valve design, Dial Regulators have transparent, pressure-calibrated, non-rising adjustment dial used to adjust secondary pressure. Full reduced pressure range can be dialed in less than 270°, and dial can be color- or graphics-coded. Products are available in 4 body sizes with ports from ¼-2 in. and have two ¼ in. gauge ports. Relief and flow capacities are available from 0.7 scfm (model 51R) to 1,600 scfm (model 54R).