SMSC
Hauppauge, NY 11788
Jul 21, 2008 Suited for consumer electronics and computing applications, USB2240 and USB2250 Hi-Speed USB 2.0 controllers offer read and write support for 24 Flash media formats and help reduce bottlenecks with throughput speeds to 35 Mb/s. Series USB2240 uses multiplexed Flash media interfaces in 36-pin QFN package, while USB2250 comes in 128-pin VTQFP and supports simultaneous access to different Flash media formats. Both fully integrated, single-chip solutions support -40 to 85°C operation.

GOEPEL electronics LLC
Austin, TX 78759
Jul 10, 2008 Incorporating normally external SCANFLEX® transceivers into 1 slot/3U unit, SCANFLEX® SFX/PXI1149/C4-FXT Boundary Scan Controllers feature ADYCS(TM) II propagation delay compensation and dynamic HYSCAN(TM) data splitting. TAP interface cards are linked externally, and 4 auto-identified TIC types are available. Differential signal interface ensures secure transmission of TAP signals, even through multiple interconnections and with over 4 m of cable length, maintaining TCK clock frequency up to 80 MHz.

Beckhoff Automation LLC
Minneapolis, MN 55337
Jul 01, 2008 Suitable for drives with quadratic load characteristics such as fans and pumps, Model KL2791 Bus Terminal I/O system enables direct connection of small, 1 A, single-phase motors rated 120 V, 60 Hz, in order to achieve setting range for flow rate from 10-100%. Set value for motor speed is specified by 16-bit value, and motor is switched on and off with mains synchronous pattern. Compact speed controller comes in standard bus terminal housing with width of 12 mm.

TURCK, Inc.
Plymouth, MN 55441
May 21, 2008 Vertical mount JRBS junction bricks for FOUNDATION fieldbus(TM) are available with 4, 6, 8, 10, or 12 ports and feature removable terminals located on both sides of brick. Units provide short circuit protection for all ports, as well as visual status with bright LED indicators located on each spur. DIN-mounted vertically or horizontally, they are also available with optional overmolded, pluggable terminating resistor for use with 3-pole terminal blocks.

Pilz Automation Safety L.P.
Canton, MI 48187
Mar 03, 2008 PSSuniversal consists of head module, which undertakes all communication and processing functions, and base modules, connected to head modules, used for installing electronic modules as well as connecting I/O signals. Up to 64 components, each consisting of one base and one electronic module, may be operated per head module. Combining intelligent safety and standard control functions, system is established automatically; included software tool facilitates setup.

Moore Industries International, Inc.
North Hills, CA 91343
Dec 06, 2007 Requiring 10.5 mA to operate, programmable Model TFZ allows up to 32 field devices (126 with repeaters) to be networked onto one FOUNDATION Fieldbus H1 segment. It has 20-bit input resolution, RFI/EMI protection, ambient temperature compensation, and operates in -40 to +85°C temperatures. Rated NEMA 4X/IP66, TFZ can be set from control room over segment wiring to handle 14 RTD types, 9 thermocouple types, as well as direct mV and resistance/potentiometer inputs.

Pepperl+Fuchs
Twinsburg, OH 44087
Oct 22, 2007 FieldConnex® High Density (HiD) Power Hub includes motherboards and power supplies that use 25 V to supply 360 mA load output. They offer heat dissipation of less than 2 W, and can be mounted in any direction. Choice of motherboards exist to fit any control system, and can be pre-installed using connectors with retaining screws or tailor-made versions with system plugs of DCS. Two power supply modules are load sharing, and can be plugged into motherboard's sockets when system is energized.

TURCK, Inc.
Plymouth, MN 55441
Jul 18, 2007 Suited for pharmaceutical, chemical, and material handling industries, FDP20 I/O Stations are available in versions with 16 inputs, 16 inputs/outputs, and 8 inputs paired with 8 inputs/outputs. Glass-filled nylon housing with integrated DIN-rail connector provides IP 20 protection and makes stations suitable for integrating I/O in existing panels onto PROFIBUS. Nine-pin female D connector provides connection to PROFIBUS-DP, and all power is derived from separate power source.

VersaLogic Corp.
Eugene, OR 97402
Jul 17, 2007 Available for standard and custom functions, RoHS-compliant Serial Peripheral eXpansion(TM) (SPX(TM)) modules implement SPI Bus that operates on 14-pin interconnect cable. Offerings include 8-channel analog input module, CANbus controller, 4-channel analog output module, TTL I/O port expansion, and 8-channel solid state switch. Up to 4 SPX modules, of identical or different functionality, can be used per system (bolted to host board or located up to 2 ft away).

Pepperl+Fuchs
Twinsburg, OH 44087
May 08, 2007 Designed for FOUNDATION Fieldbus H1 and PROFIBUS PA installations, Mobile Advanced Diagnostic Module provides exact segment and individual device data needed for fieldbus physical layer analysis without need for permanent connection. Passive input circuits and external power supply leave physical layer untouched. Also included, Diagnostic Manager offers commissioning wizard, alarming and data logging, and built-in oscilloscope for displaying in-depth detail of fieldbus signals.

Freescale Semiconductor
AUSTIN, TX 78735-8598
Apr 18, 2007 Both MCF5221x MCUs with Full-Speed USB On-The-Go (OTG) and MCF5253 embedded processor with Hi-Speed USB OTG come with USB software stack, enabling developers to streamline design process. USB OTG gives option of using on-chip USB module as USB device or USB host. It also allows multiple USB devices to communicate without host interface. Integrating USB transceivers on chip, 32-bit ColdFire® USB devices provide integrated embedded control for designers who need USB connectivity.

ICS Electronics Corp.
Pleasanton, CA 94588
Feb 28, 2007 Used for controlling test instruments and collecting data, Model 488-USB2 converts any PC with USB 1.1/2.0 interface into full-function, IEEE 488.2-compatible bus controller. Plug-and-play device operates from any open GPIB connector and has 1 MBps data rate. Along with 488.2V3 Driver Library that supports up to 16 GPIB Controllers, product comes with Explorer utility that automatically locates, displays, and configures GPIB controllers and devices in system.

Moore Industries International, Inc.
North Hills, CA 91343
Dec 14, 2006 Available in simplex (non-redundant) and duplex (redundant) models, FPS200 TRUNKGUARD Fieldbus Power Conditioner provides conditioned power in general purpose and non-incendive applications. Simplex configuration allows up to 8 modules to be installed on single DIN-rail carrier, with each module providing 350 mA at 26 V of isolated power, fully compliant with FF831-1 specification. Duplex configuration provides redundant, load-sharing, and hot-swappable power conditioners.

Moore Industries International, Inc.
North Hills, CA 91343
Oct 31, 2006 ATEX-certified TG300 TRUNKGUARD Device Coupler connects FOUNDATION Fieldbus H1 or PROFIBUS PA fieldbus devices in flameproof Zone 1 and 2 locations. Available in 4 or 8 fieldbus device models, coupler can accommodate additional field devices and link with other units to power as many devices as segment can support. TG300 has short-circuit protection, Automatic Segment Termination, and LED status indicators.

Pepperl + Fuchs, Inc.
Twinsburg, OH 44087 2245
Oct 27, 2006 Suitable for FOUNDATION Fieldbus and Profibus installations, Advanced Diagnostic Module for FieldConnex® Power Hub generates network documentation for each segment and device and controls fieldbus by monitoring physical layer. Built-in oscilloscope can be set to trigger on numerous events, allowing maintenance personnel to pinpoint fault locations from control room utilizing Device Type Manager. During commissioning, ADM makes snapshot of communication quality for trending changes over time.

Moore Industries International, Inc.
North Hills, CA 91343
Oct 06, 2006 Providing redundancy and automatic switchover in case of segment fault, TRUNKSAFE(TM) fieldbus system helps prevent loss of segment and potential process failures. Unit consists of 2 redundant TPS200 fieldbus power conditioners, 2 fieldbus cables, and 1 TS200 fail-safe device coupler to handle 6 or 10 fieldbus devices. System also offers hard-wired alarm to alert plant operators about cable fault, while LEDs indicate exactly which cable and what type of fault has occurred.

Woodhead Industries Inc.
Deerfield, IL 60015
Sep 01, 2006 Suited for applications where in-cabinet mounting, high-density I/O count, and modular design are required, IP20 BradControl(TM) Block I/O System connects industrial I/O devices to PLC or PC controller over industrial network. It is comprised of network adapter and up to 32 expansion modules mounted in enclosure. Ribbon cable-based expansion bus, which handles inter-module communication, operates at 11 MBaud and can accommodate up to 10 groups of modules.

Pepperl + Fuchs, Inc.
Twinsburg, OH 44087 2245
Sep 01, 2006 Supporting redundant 24 V power, Model KLD2-FBPS-1.25.360 galvanically isolated Foundation Fieldbus power supply provides 25 V and 360 mA of supply current with minimal heat dissipation, allowing modules to be mounted adjacent to one another without concern for spacing. Passive power conditioning (signal filter) makes it suitable for single segment power needs, and it supports connection to mobile advanced diagnostic module for physical layer diagnostics.

B & R Industrial Automation Corp.
Roswell, GA 30076
Aug 28, 2006 Comprised of base module, power supply module, and fieldbus interface, 1.5 in.-wide X20 bus controller enables real-time Ethernet cycle times of 200 µs. Entire bus-independent backplane can be preinstalled, and 2 RJ45 interfaces make daisy chain wiring possible. To transfer or receive I/O data on fieldbus, bus controller works by configuring fieldbus master and does not need to be programmed. Product is fully synchronized to network and all axes connected to it.

Moore Industries International, Inc.
North Hills, CA 91343
Aug 02, 2006 Available with 4, 8, or 10 fieldbus spurs, TG200 TRUNKGUARD(TM) Series uses fold-back technique to disconnect shorted instrument from fieldbus segment and prevent complete segment failure. Automatic Segment Termination feature, also included, simplifies commissioning and startup by eliminating problems caused by over- or under-termination. Series works with FOUNDATION fieldbus H1 and PROFIBUS PA interfaces, and up to 32 fieldbus devices can be accommodated in one segment.