Tektronix, Inc.    Beaverton, OR 97077
Mar 20, 2013 With Option MCS software, OM4000 Optical Modulation Analyzers offer automated test support for 400 G multi-carrier coherent optical modulation. To launch test, user enters multi-carrier variables such as number of carriers, carrier spacing, and modulation format. Software automatically steps through each carrier, setting up local oscillator and measurement parameters. When measurements are complete, system provides results from carriers side-by-side for correlation and identification of problems.

GAO Instruments Inc.,    Toronto   Canada
Mar 14, 2013 Designed for construction and maintenance of PON networks which can be connected between OLT and ONT, model C0260007 enables accelerated testing of all PON signals along network. Portable unit performs simultaneous measurement and display of PON signals, including voice, data, and video optical signal. Simultaneously measuring all 3 wavelengths on fiber (1,490, 1,550, and 1,310 nm), tool provides 10 groups of configurable threshold values and can save 1,000 test results.

Polystar Group    Frisco, TX 75034
Mar 11, 2013 With complex functionalities such as VoLTE with SRVCC hand-over, Solver is suited for voice load testing in 2G/3G and 4G networks. Solution delivers full wire-speed load on 10 Gb Ethernet ports with voice traffic that helps communication service providers and network manufacturers to test voice handling and voice quality in labs and networks. Operation can be initiated from central management system, allowing control of all aspects of core network testing and simulation of user behavior.

Megger    Norristown, PA 19401
Mar 07, 2013 Able to measure logical network performance and physical condition of network cables, NET200 helps network engineers install and maintain LANs with 10BASE-T/100BASE-TX based Ethernet protocol. Unit uses round-trip time testing to measure network speed under dynamic and static configuration protocols as well as IP scanning to show information on all terminals connected into LAN. Tool also evaluates capability of link connections, including network speed and full- or half-duplex suitability.

Boeing Co., The    Seattle, WA 98124
Mar 06, 2013 With its Software Defined Radio architecture and wideband receiver, DRT4311B enables wireless carriers and infrastructure providers to assess their cellular network and identify areas where upgrades may be required. Functionality allows for simultaneously scanning between 2G, 3G, and 4G networks with wireless control application compatible with any Android device.

MT2    Arvada, CO 80004
Feb 22, 2013 As FPGA-based server, XG-PON Platform can work as analyzer or OLT emulator for XG-PON1 networks. Test tool can analyze XG-PON1 bitstreams in real-time and continuously. Neutral and non-intrusive system features client-server architecture, while GUIs offer comprehensive view of network. BBF.247 test-suite supports IR-247 issue 2 test-plan.

Agilent Technologies, Inc.    Santa Clara, CA 95051
Feb 18, 2013 Built into PNA-X Network Analyzers, source-corrected noise-figure measurement technique provides single-connection, multiple-measurement capability for users developing and testing low-noise transistors, amplifiers, frequency converters, and transmit/receive modules. Analyzers combine S-parameter vector-error correction and impedance tuner to remove effects of imperfect system source match. Solution also corrects for interaction between output match of DUT and noise figure of internal receiver.

Ideal Industries, Inc.    Sycamore, IL 60178
Jan 14, 2013 SignalTEK® II Qualifier tests and troubleshoots critical functions required for IP physical security system success and generates documentation. Solution verifies copper or fiber cabling can support IP-based video surveillance applications over 10/100 Megabit or Gigabit Ethernet. It also tests IP connections, validates DHCP and static IPv4 and IPv6 addressing, tests Internet and cloud connections, and ensures connectivity to NVRs, video clients, decoders, and wireless nodes.

Megger    Norristown, PA 19401
Jan 08, 2013 Used to test voice and data circuits during copper-wire installations, HT1000/2 provides maintenance technicians with means for certifying physical layer of telephone network and its xDSL transmission characteristics as well as Home Phoneline Network Alliance (HPNA) data/video networks. Automatic Super Stress mode helps identify difficult short loop imbalances during longitudinal balance testing. Other features include dual-trace TDR, wideband spectrum analyzer, and intuitive menu system.

Megger    Norristown, PA 19401
Dec 12, 2012 With NET200, users can evaluate performance of LANs that use 10BASE-T or 100BASE-TX Ethernet protocols. Handheld instrument uses round-trip time testing to measure network speed under dynamic and static configuration protocols, and IP scanning to show information about all terminals connected to network. Powered by rechargeable Li-Ion battery, tester also provides information about physical condition of network cables and has TDR/TDX functions for locating faults in cables up to 500 m long.

Anritsu Co.    Morgan Hill, CA 95046
Nov 09, 2012 Combining signal and coverage analysis, vector network analysis, and spectrum analysis, LMR Master™ S412E is used for ensuring proper deployment, installation, and maintenance of commercial Land Mobile Radio (LMR) and public safety networks used by first responders. Complete solution supports Narrowband Analog FM, both FMDA and TDMA P25, NXDN™, ETSI DMR / MotoTRBO™, FD-LTE for FirstNet broadband public-safety LTE deployments, and Positive Train Control (ITC-R) standard.

Uptrends    Burlington, MA 01803
Oct 16, 2012 With Uptrends Website Monitoring Service, users can set unlimited SLA settings for all probe groups and clients. Users can add specific goals such as uptime%, total time, and operator response time for every SLA setting. Aside from setting weekdays and hours that apply to SLA, users can define exclusion periods such as holidays. By entering parameters into SLA settings, Uptrends can produce daily, weekly, and monthly monitoring reports indicating when and why if uptime standards are not met.

Agilent Technologies, Inc.    Santa Clara, CA 95051
Sep 21, 2012 Available for E5071C ENA series network analyzer, upgrade options E5071CU-041 and E5071CU-042 respectively replace 1.86 and 1.3 GHz Intel® Celeron® processors for 2.53 GHz Intel Core™ i7 processor to accelerate save/recall time. Digital hardware upgrade options also change E5071C ENA storage device from HDD to SSD, accelerating boot time.

Agilent Technologies, Inc.    Santa Clara, CA 95051
Sep 06, 2012 Available in frequencies of 9, 14, 18, or 26.5 GHz, FieldFox Analyzers can be configured as cable-and-antenna analyzers, spectrum analyzers, vector network analyzers, or combination units. VNAs provide 2-port S-parameter measurements with trace noise of ±0.004 dB and dynamic range of 94 dB. Spectrum analyzers provide amplitude accuracy of ±0.5 dB at power-up, with no warm-up required. For harsh environments, units have sealed enclosure, compliant with MIL-PRF-28800F Class 2 requirements.

Anritsu Co.    Richardson, TX 75081
Jul 05, 2012 Providing return loss, cable loss, and Distance-to-Fault measurements, Site Master S331L features sweep speed per data point of 1.5 msec, accelerating identification of intermittent problems in real-time. Built-in InstaCal(TM) provides one-connection calibration anytime, while built-in power meter enables testing of RF power in field environments. Dust- and splash-resistant with 7 in. backlit TFT touchscreen, analyzer provides 8 hours of continuous battery life.

Anritsu Co.    Richardson, TX 75081
Jul 03, 2012 Able to be used for 4-port and differential mm-wave component development, VectorStar® ME7838A Vector Network Analyzer (VNA) features stability, real-time power leveling control, and 70-110 GHz frequency coverage. This test tool can be mounted on probe station using standard positioners and includes MS4640A VectorStar and 3739A test set, which operates mm-wave modules. Dynamic range is 108 dB at 65 GHz and 107 dB at 110 GHz, and measurement speed is 55 ms for 201 points at 10 kHz IFBW.

Anritsu Co.    Richardson, TX 75081
Jul 03, 2012 With Option MS4640A-041, VectorStar MS4640A and ME7838A are capable of measuring noise figure from 70 kHz to 125 GHz, enabled in part by receiver optimized for measurements from 30-125 GHz. Noise figure measurements enable test engineers to determine potential degradation of signal-to-noise ratio from system components in applications including radar, wireless communications, and digital communications.

Agilent Technologies, Inc.    Santa Clara, CA 95051
Jun 28, 2012 Replacing existing N5230C models, N523xA Series PNA-L Analyzers are available in 5 frequency models. Three frequency models start at 300 kHz, with 2 or 4 ports available for 13.5 and 20 GHz models, and 2 ports available for 8.5 GHz version. Other two frequency models, with 2 ports, start at 10 GHz and include 43.5 and 50 GHz products. Units offer open architecture based on Microsoft Windows® OS and advanced connectivity via LAN, USB, and GPIB.

Fluke Networks    Camarillo, CA 93010
Jun 25, 2012 Via automated troubleshooting of common end-user issues, OneTouch(TM) AT Network Assistant reduces time technicians need to close network trouble tickets. Handheld tool has one-button auto test feature and is able to test 802.11 a/b/g/n Wi-Fi as well as copper and fiber gigabit Ethernet networks. Along with in-line copper and fiber packet capture, features include cable wire mapping, PoE, and link testing support; remote access for collaboration; smartphone touchscreen-based operation.

Fluke Networks    Camarillo, CA 93010
Jun 07, 2012 Providing data center visibility, OptiView XG helps identify issues and root causes in minutes. One-Click Test finds connection path in single screen view. Once analysis is complete, engineers can provide consolidated summary report which indicates whether problem is with network or server. If not a network problem, Automated Multi-Segment Analysis feature can be used with another OptiView XG to capture and merge trace files from multiple segments to find where loss and latency are occurring.