Trend Communications Ltd.
Maidenhead   United Kingdom
Nov 17, 2008 Multipro Copper tester allows single operator to measure all parameters of cable from near end to far end using optional transponder, which receives control signals generated by tester and sent down cable under test. Device incorporates test functions for frequency response, return loss, and noise, and diagnostics for crosstalk, induced voltages, interference, and noise. Analysis is carried out using integral spectrum analyzer, oscilloscope, and time domain reflectometer.

JDSU
San Jose, CA 95131
Nov 17, 2008 Designed to help prevent network downtime caused by contaminated (dirty) fiber, HD3-P provides technicians handling optical fiber with dedicated microscope for patch-cord inspections and probe microscope for bulkhead connector port inspections. Handheld display with 1.8 in. TFT LCD screen and probe delivers 2-in-1 functionality, eliminating need to change inspection tips. This prevents misplacing and mishandling of inspection tips that can cause cross-contamination of fiber.

QuadTech, Inc.
Maynard, MA 01754
Nov 06, 2008 In addition to Hipot function that can test up to 1,500 Vdc and 1,067 Vac, Meridian performs open, short, and miswire tests up to 500 wires/sec. Unit features Windows-based user interface, color touch-screen, 3 log-in levels of protection for security of data and testing procedures, and solid state hard drive, which can be transported and upgraded. With USB host port technology and Ethernet card, users can transfer stored data to PC or network.

GAO Tek Inc.
Toronto M1B2K4  Canada
Aug 26, 2008 Able to locate line faults in cables such as POTS and xDSL, GAO5221 xDSL Subscriber Loop Analyzer test capabilities include Vac/Vdc for twisted pair copper cable, resistance, ac/dc current, capacitance, frequency response, noise, and coil load. Unit can measure maximum available bit rate supported by local loop without need of xDSL modem, and locate bridge taps, shorts, and opens.

Anritsu Co.
Richardson, TX 75081
Aug 15, 2008 Single slot CMA5710 module for CMA 5000 enables testing of 10/100/1000 Mbps Ethernet networks. Module provides 2 optical (SFP) and 2 electrical (RJ45) ports, and is designed to facilitate installation and maintenance of Ethernet networks. RFC2544 test functions include: throughput, latency, and frame loss. For maintenance and troubleshooting, module provides non-intrusive monitoring capabilities and presents comprehensive statistics for insight into network health and status.

Fluke Networks
Camarillo, CA 93010
Aug 14, 2008 Comprised of installation and service tools, MicroScanner2 Termination Test Kit offers everything required to locate, terminate, and verify copper cabling installations. MicroScanner2 Cable Verifier delivers visual representations of test results, and IntelliTone Pro Probe accelerates identification of specific wire pairs and cables on active networks. Other components include adapters and patch cords, impact tool, electrician D-Snips(TM), and adjustable wire cutter-stripper.

CAMI Research Inc.
Acton, MA 01720
Aug 13, 2008 PC-based CableEye® checks cables and wire harnesses for opens, shorts, and miswires; measures diode forward voltage; checks resistance values from 0.3 W to 10 MW; and tests conduction and isolation resistance against specified thresholds. Its Light Director(TM) accessory delivers computer-assisted technique for assembling circular connectors. Light fibers, driven by super-bright LED lamps, individually illuminate target cavities, and synthetic speech can also read pin number.

Sunrise Telecom Inc.
San Jose, CA 95119
Jul 29, 2008 Enabling accurate triple play deployment, Home Test Toolkit(TM) allows technicians to test key interfaces, signals, and functions at customer location during installation. Unit indicates probable locations and causes of problems, and ensures timely delivery of IPTV and other network services. Tester performs automatic go-no-go test routines for VDSL, VDSL2, HPNA networks, and RF signal level as well as Ethernet, 802.11 WiFi, copper loop fault identification, and ground continuity testing.

HD Electric Co.
Waukegan, IL 60085
May 27, 2008 With ability to identify correct phases of de-energized and discharged overhead and underground cables, PF-50 Cable Identifier consists of transmitter and receiver that are designed to be hand-held, with or without gloves, or that can be mounted and used on hotsticks. High test voltage enables device to test full mile of cable. Bright red LEDs on both units indicate that PF-50 units are connected to same cable.

CAMI Research Inc.
Acton, MA 01720
May 19, 2008 With software, CableEye® Cable and Wire Harness Tester enables use of synthetic speech and voice recognition for hands-free operation. Voice recognition permits operator to issue commands to tester without pushing buttons or keyboard keys. Featuring noise-canceling microphone, single-ear USB headset allows system to operate in noisy environments without interfering with other workers. Voice control can be used alone or in combination with button controls and barcode scanning.

RF Industries
San Diego, CA 92126 4202
Apr 28, 2008 Housed in foam-lined impact resistant plastic case, RFA-4028-WIFI kit contains Unidapt RF Cable tester (RFA-4018-20) with 30 universal adapters, including male and female MMCX, N, Reverse Polarity TNC, Reverse Polarity SMA, TNC, BNC, and SMA connector interfaces. RFA-4018-20 coaxial cable tester is solid-state continuity checker that measures for opens and shorts. LED display indicates continuity for shield and center conductor, as well as checks for shorting across conductor paths.

CAMI Research Inc.
Acton, MA 01720
Apr 23, 2008 CableEye® checks cables and wire harnesses for opens, shorts, and miswires; measures diode forward voltage; checks resistance values from 0.3 W to 10 MW; and tests conduction and isolation resistance against thresholds. Optional API, software primitives used to exercise control over all basic functions of tester via external program, lets test engineers write software for CableEye in Visual Basic, VB.NET, C++, C#, or from any environment that can host Active-X software interface.

Teseq, Inc.
Edison, NJ 08837
Feb 12, 2008 ISN T8-Cat6 impedance stabilization network (ISN) is designed for measurements on up to 4 unshielded single balanced pairs of cables. CISPR 22-based coupling/decoupling network features maximum line-to-ground voltages of 63 Vac and 100 Vdc and maximum current ratings of 400 mA/line and 800 mA/pair. Measuring 105 x 65 x 110 mm and weighing 550 g, it offers coupling path connection of BNC 50 W and RF voltage of less than 15 V as well as 0 ±20° phase angle.

Smartronix Inc.
California, MD 20619
Jan 18, 2008 Designed to test Ethernet patch cables for continuity and common wiring standards, PatchTest(TM) cable tester is fully compatible with company's existing line of SuperLoopers. Through its LED lights, unit indicates Gigabit Ethernet Straight Through, 10/100 Mb Fast Ethernet Straight Through, 10/100 Mb Fast Ethernet Crossover, and bad or unidentified cable. Weighing less than 2 oz, it features blue molded plastic body and key-chain attachment.

Teseq, Inc.
Edison, NJ 08837
Jan 09, 2008 Suited for 1000BaseT and PoE applications, CISPR 22-based ISN T8 measures conducted common mode disturbances on up to 4 unshielded single balanced pairs of cables within equipment under test. It consists of ISN T800 network with D-Sub-25 connectors and LCL adapter sets for Cat 3 and Cat 5 cables. With frequency range of 150 kHz to 30 MHz, network features max line-to-ground voltages of 63 Vac and 100 Vdc, and max current ratings of 400 mA/line and 800 mA/pair.

CAMI Research Inc.
Acton, MA 01720
Dec 12, 2007 Using built-in scripting for pre-programming, PC-based CableEye can test cable, log test result to archive, print report, print label, or take conditional actions depending on pass or fail result. When program's language preference is changed from English to Spanish, screen labels, dialog boxes, advisory screens, and error messages appear in Spanish text to benefit operator. Program may be changed from one language to another at login.

Honeywell
Madison, WI 53711
Nov 08, 2007 Plug-in cable tester lets CE Installers perform on-site HDMI cable and DVI cable assembly performance verification, ensuring that all of their circuits and connections are 100% operational. Unit sends controlled signals through all 19 conductors within HDMI interface, and 9 LEDs illuminate one-by-one as each discrete function of HDMI cable is confirmed. If any LED fails to light, cable is defective and must be replaced.

Agilent Technologies, Inc.
Palo Alto, CA 94303
Sep 17, 2007 With WireScope Pro LAN Cable Tester and v2.5 software, users can ensure proper certification of structured cabling in presence of Power over Ethernet mid-span devices and ac-coupled patch-panels. Tester features frequency range up to 1 GHz and is capable of testing all common cable standards, even beyond ISO/IEC Class F limit of 600 MHz.

Agilent Technologies, Inc
Santa Clara, CA 95051
Sep 10, 2007 Operating up to 4 hr on one charge, handheld Agilent N9330A delivers basic test functionality to aid in installation and maintenance of wireless service, military communications, broadcasting, and radio links. Battery-operated unit covers 25 MHz to 4 GHz range and features distance-to-fault measurement functions, USB connectivity, and post-analysis software. Product lets users choose 131, 261, or 521 test points and operates at speeds to 3.0 msec per data point.

Ideal Industries, Inc.
Sycamore, IL 60178
Apr 17, 2007 SIGNALTEK-FO measures copper and fiber optic cabling system performance according to IEEE 802.3 standards. Along with Gigabit Ethernet Bit Error Rate Testing, features include active LAN diagnostic testing, 32 MB internal memory for storing up to 20,000 tests, and printed pass/fail qualification reporting. Dual wavelength capability enables switching from 850 to 1,300 nm, while multimode and single mode capability permits qualification of cabling to max distance of 6.2 miles.