HD Electric Co.
Waukegan, IL 60085
May 27, 2008 With ability to identify correct phases of de-energized and discharged overhead and underground cables, PF-50 Cable Identifier consists of transmitter and receiver that are designed to be hand-held, with or without gloves, or that can be mounted and used on hotsticks. High test voltage enables device to test full mile of cable. Bright red LEDs on both units indicate that PF-50 units are connected to same cable.

CAMI Research Inc.
Acton, MA 01720
May 19, 2008 With software, CableEye® Cable and Wire Harness Tester enables use of synthetic speech and voice recognition for hands-free operation. Voice recognition permits operator to issue commands to tester without pushing buttons or keyboard keys. Featuring noise-canceling microphone, single-ear USB headset allows system to operate in noisy environments without interfering with other workers. Voice control can be used alone or in combination with button controls and barcode scanning.

RF Industries
San Diego, CA 92126 4202
Apr 28, 2008 Housed in foam-lined impact resistant plastic case, RFA-4028-WIFI kit contains Unidapt RF Cable tester (RFA-4018-20) with 30 universal adapters, including male and female MMCX, N, Reverse Polarity TNC, Reverse Polarity SMA, TNC, BNC, and SMA connector interfaces. RFA-4018-20 coaxial cable tester is solid-state continuity checker that measures for opens and shorts. LED display indicates continuity for shield and center conductor, as well as checks for shorting across conductor paths.

CAMI Research Inc.
Acton, MA 01720
Apr 23, 2008 CableEye® checks cables and wire harnesses for opens, shorts, and miswires; measures diode forward voltage; checks resistance values from 0.3 W to 10 MW; and tests conduction and isolation resistance against thresholds. Optional API, software primitives used to exercise control over all basic functions of tester via external program, lets test engineers write software for CableEye in Visual Basic, VB.NET, C++, C#, or from any environment that can host Active-X software interface.

Teseq, Inc.
Edison, NJ 08837
Feb 12, 2008 ISN T8-Cat6 impedance stabilization network (ISN) is designed for measurements on up to 4 unshielded single balanced pairs of cables. CISPR 22-based coupling/decoupling network features maximum line-to-ground voltages of 63 Vac and 100 Vdc and maximum current ratings of 400 mA/line and 800 mA/pair. Measuring 105 x 65 x 110 mm and weighing 550 g, it offers coupling path connection of BNC 50 W and RF voltage of less than 15 V as well as 0 ±20° phase angle.

Smartronix Inc.
California, MD 20619
Jan 18, 2008 Designed to test Ethernet patch cables for continuity and common wiring standards, PatchTest(TM) cable tester is fully compatible with company's existing line of SuperLoopers. Through its LED lights, unit indicates Gigabit Ethernet Straight Through, 10/100 Mb Fast Ethernet Straight Through, 10/100 Mb Fast Ethernet Crossover, and bad or unidentified cable. Weighing less than 2 oz, it features blue molded plastic body and key-chain attachment.

Teseq, Inc.
Edison, NJ 08837
Jan 09, 2008 Suited for 1000BaseT and PoE applications, CISPR 22-based ISN T8 measures conducted common mode disturbances on up to 4 unshielded single balanced pairs of cables within equipment under test. It consists of ISN T800 network with D-Sub-25 connectors and LCL adapter sets for Cat 3 and Cat 5 cables. With frequency range of 150 kHz to 30 MHz, network features max line-to-ground voltages of 63 Vac and 100 Vdc, and max current ratings of 400 mA/line and 800 mA/pair.

CAMI Research Inc.
Acton, MA 01720
Dec 12, 2007 Using built-in scripting for pre-programming, PC-based CableEye can test cable, log test result to archive, print report, print label, or take conditional actions depending on pass or fail result. When program's language preference is changed from English to Spanish, screen labels, dialog boxes, advisory screens, and error messages appear in Spanish text to benefit operator. Program may be changed from one language to another at login.

Honeywell
Madison, WI 53711
Nov 08, 2007 Plug-in cable tester lets CE Installers perform on-site HDMI cable and DVI cable assembly performance verification, ensuring that all of their circuits and connections are 100% operational. Unit sends controlled signals through all 19 conductors within HDMI interface, and 9 LEDs illuminate one-by-one as each discrete function of HDMI cable is confirmed. If any LED fails to light, cable is defective and must be replaced.

Agilent Technologies, Inc.
Palo Alto, CA 94303
Sep 17, 2007 With WireScope Pro LAN Cable Tester and v2.5 software, users can ensure proper certification of structured cabling in presence of Power over Ethernet mid-span devices and ac-coupled patch-panels. Tester features frequency range up to 1 GHz and is capable of testing all common cable standards, even beyond ISO/IEC Class F limit of 600 MHz.

Agilent Technologies, Inc
Santa Clara, CA 95051
Sep 10, 2007 Operating up to 4 hr on one charge, handheld Agilent N9330A delivers basic test functionality to aid in installation and maintenance of wireless service, military communications, broadcasting, and radio links. Battery-operated unit covers 25 MHz to 4 GHz range and features distance-to-fault measurement functions, USB connectivity, and post-analysis software. Product lets users choose 131, 261, or 521 test points and operates at speeds to 3.0 msec per data point.

Ideal Industries, Inc.
Sycamore, IL 60178
Apr 17, 2007 SIGNALTEK-FO measures copper and fiber optic cabling system performance according to IEEE 802.3 standards. Along with Gigabit Ethernet Bit Error Rate Testing, features include active LAN diagnostic testing, 32 MB internal memory for storing up to 20,000 tests, and printed pass/fail qualification reporting. Dual wavelength capability enables switching from 850 to 1,300 nm, while multimode and single mode capability permits qualification of cabling to max distance of 6.2 miles.

CAMI Research Inc.
Acton, MA 01720
Mar 12, 2007 CableEye® cable and wire harness tester comes with software that displays multiple, independent connector graphics with live video graphics to aid in visualization of complex wiring. Users can view detailed information on pins or termination and compare model cable data with test data to locate wiring faults. Along with wire resistance testing, solution offers rubber-banding tool and grid display. Check for intermittent connections runs at over 10 scans/sec while cable is flexed.

Agilent Technologies, Inc
Santa Clara, CA 95051
Oct 05, 2006 Integrated sink, source, and cable test system is used for manual and automated HDMI physical-layer compliance tests, as well as for margin-test and characterization for R&D and manufacturing. System comprises oscilloscopes, time domain reflectometer, ParBERT-based TMDS signal generator, test automation software, and HDMI-specific accessories. Controlled via point-and-click operations, system targets consumer electronics manufacturers, semiconductor, and cable manufacturers.

Sunrise Telecom Inc.
San Jose, CA 95119
Jun 20, 2006 SunSet® Modular Test Toolkit (SSMTT)-41 module is designed for testing VDSL-based triple-play network deployments. In addition to verifying inside wiring is capable of supporting IPTV signals, unit verifies cable continuity, detects broken diplexers, provides cable identification, and estimates cable length. Multifunctional test tool includes VDSL modem, HPNA analyzer, RF signal level meter, spectrum analyzer, and wiring test features.

Ideal Industries, Inc.
Sycamore, IL 60178
Jun 02, 2006 Used to verify that installed cabling will support voice, video, and data applications, SIGNALTEK offers Gigabit performance testing by transmitting 10/100/1000 Mbps Ethernet packets and measuring errors on link in accordance with IEEE 802.3ab Gigabit Ethernet standard. Handheld device also supports Bit Error Rate Testing (BERT) and integrates time domain reflectometer. Along with monitoring mode, unit features intelligent autotest function and 32 MB internal memory for data storage.

JDSU
San Jose, CA 95131
Feb 09, 2006 Integrated with Stealth Sweep(TM) technology, Digital Services Analysis Meter (DSAM) 6000 supports VoIP, high-speed data, and digital/analog video deployments. Hand-held test instrument incorporates forward and reverse sweep functions, enabling it to identify transmission errors that cause digital impairments by measuring network frequency response. Non-interfering, continuously referenced sweep tracing helps reveal physical errors in network that influence transmitted signals.

Agilent Technologies, Inc.
Palo Alto, CA 94303
Jan 31, 2006 Able to perform automated point-to-point tests on Cat 3 to Cat 6 cable/fiber, WireScope Pro has expandable architecture that can be upgraded to test up to Cat 6a/7. Cable and fiber tester features Alien Crosstalk measurement capability and runs measurements in 5 min. Operated via touch-screen interface on color LCD, product utilizes Fiber SmartProbes that eliminate need to swap fibers for bidirectional testing and calibration. Measurement frequency range is 1 GHz.

RF Industries
San Diego, CA 92126 4202
Jan 05, 2006 Used to detect open and short faults in coaxial cable assemblies, RFA-4018-20 is constructed with Unidapt® universal connector system that allows for testing of any connector with attachment of adapters from Unidapt® adapter kits. LED front panel indicates pass or fail with red or green light, and tester indicates whether failure is due to short, open conductor, or open shield. Powered via 9 V battery, unit is portable for remote site use.

RF Industries
San Diego, CA 92126 4202
Oct 07, 2004 Featuring 2 RJ-45 inputs, Model RFA-4218-20 tests straight and crossover RJ-45 UTP, STP, EIA/10Base-T, 100Base-T, EIA/TIA 568A/568B, FDDI, ATM, TP-PMD and Token Ring cables. LED display is powered by 9 V battery and indicates shorts, open wires, reversed pairs, crossed pairs, and mis-wires. Housed in black, impact-resistant plastic case, Model RFA-4218-20 automatically identifies cable type it is connected to and verifies all connections.