Wireless Receivers

Communication Systems & Equipment

GNSS RTK Receiver targets Esri community.

July 18, 2014

Weighing 1.5 lb, Model APS-NR2 works on virtually all RTK networks and communicates seamlessly with Esri cloud-based platforms. Unit features dual cellular antennae with automatic switchover, and built-in Wi-Fi that enables user to configure and monitor unit and stream data directly to tablet. Running all day on hot-swappable batteries, receiver recharges from any USB port. Open architecture lets user choose data collector software or interface directly with Esri ArcGIS Online. Read More

Communication Systems & Equipment

Miniaturized IR Receivers simplify designs for data transmission.

July 9, 2014

Specified for operation from 2.5–5.5 V, with 0.35 mA supply current at 3.3 V, TSDP34138/56 and TSDP34338/56 are designed for low-speed data transmission and consist of photodiode and preamplifier assembled on lead frame. Epoxy package (6.0 x 6.9 x 5.6 mm) acts as IR band pass filter for use with 940 nm IR LEDs. Using ASK on-off modulated 38.4 or 57.6 kHz signals from emitter with 250 mW/sr irradiance, products achieve continuous data transmission up to 7.8 kbps over range of up to 35 m. Read More

Controls & Controllers, Communication Systems & Equipment, Electronic Components & Devices

Miniature IR Receivers suit remote control applications.

December 12, 2013

With minimum irradiance of 0.12 mW/m², TSOP36... Series is available in 5 automatic gain control versions for short and long burst codes. Miniature surface mount units incorporate optical filter against IR 3D TV signals and other noise. Specified for operation from 2.5–5.5 V with transmission range up to 45 m, receivers are available for carrier frequencies from 30–56 kHz and offer low 0.35 mA supply current at 3.3 V. Applications include set-top boxes, TVs, audio systems, and digital cameras. Read More

Communication Systems & Equipment

IR Receivers are designed for 3D TV eyewear.

April 24, 2012

TSMP6000 and TSMP77000 are surface-mount IR receivers designed to receive any infrared signal used for 3D TV synchronization, simplifying design of universal 3D TV eyewear. They feature reception of raw IR 3D synchronization signals between 20-60 kHz and 800-1000 nm in wavelength. Receivers integrate photodiode, amplifier, and signal conditioning IC into a single tiny package that helps minimize weight of 3D glasses. Available with single or dual lenses, receivers feature viewing angle of ±50°. Read More

Communication Systems & Equipment, Optics & Photonics

Remote Control IR Receiver offers low, 0.8 mm profile.

April 20, 2012

TSOP57x series of remote control infrared receivers combine height of 0.8 mm, wide angle of sensitivity of 150°, and receiving distance of 40 m. At an off-axis angle of 45°, receiver retains 85% of on-axis sensitivity. Noise suppression technology has peak sensitivity of 940 nm and offers modulation frequencies of 36 kHz, 38 kHz, 40 kHz, and 56 kHz. Receivers do not use lens and are designed for TV's, set-top boxes, stereo systems, and in-room air-conditioners. Read More

Communication Systems & Equipment

SMT IR Receivers target active 3D glasses.

March 20, 2012

Dual-lens, 2.3 x 3.0 x 6.8 mm TSOP75D26 and single-lens, 4.0 x 5.3 x 7.5 mm TSOP35D26 are designed to be assembled into active 3D glasses, where they receive IR signals from TV and ensure glasses' LCD shutters open and close in proper synchronization. Both models, which operate on carrier frequency of 26.2 kHz and receive 3D synchronization signals from 830 nm emitter to avoid interference issues, comply with CEA-2038 standard and will enable consumers to watch 3D programs on any TV set. Read More

Communication Systems & Equipment, Electronic Components & Devices

Miniature IR Receivers feature 1.3 mm top-view profile.

January 20, 2011

Intended for remote control systems, TSOP85...AP5 receivers operate over carrier frequency of 36-56 kHz, offer 35 m transmission, and come in 4 AGC versions that combine PIN diode, preamp, and internal filter for PCM frequency. TSOP852..AP5 is compatible with all common IR remote control data formats, while TSOP853..AP5 and TSOP854..AP5 suppress almost all spurious pulses from energy-saving fluorescent lamps. TSOP855..AP5 is immune to dimmed LCD backlighting and fluorescent lamps. Read More

Communication Systems & Equipment, Electronic Components & Devices

IR Receivers operate in extremely noisy environments.

November 30, 2010

Suited for remote control systems, AGC5 Series is immune to dimmed LCD backlighting, noise from plasma screens, and fluorescent lamps. Miniaturized, automatic gain control, category 5 units each include photo detector and preamplifier circuit, mounted within epoxy-encapsulated module that acts as IR filter. Specified for 2.5-5.5 V operation, receivers feature carrier frequency range from 30-56 kHz, 0.35 mA supply current, and minimum irradiance of 0.1-0.15 mW/m². Read More

Communication Systems & Equipment

IR Receivers are assembled into active 3D glasses.

August 20, 2010

Developed for LCD shutter glasses used with 3D-ready TV sets, dual lens Model TSOP75D25 and single lens Model TSOP35D25 each combine photodiode, amplifier, automatic gain control, band pass filter, demodulator, and control IC into single package. Units receive IR signals from TV set and ensure LCD shutters open and close in proper synchronization to create 3D effect. Operating on carrier frequency of 25 kHz, devices avoid interference from TV and set-top box remote controls. Read More

Computer Hardware & Peripherals, Communication Systems & Equipment, Electronic Components & Devices

FSK Transceiver features star network management.

August 19, 2010

Operating in 27 MHz worldwide ISM band, Model AS3900 avoids interference found in 2.4 GHz band. Unit requires 2.5 µA in polling mode and typically 3.8 and 4.9 mA in receive and transmit modes, respectively. Built-in star network management protocol provides hardwired protocol for self management of all network functions. Transmitting data at up to 212 Kbps, device integrates power amplifier, clock, 24 bits of one-time programmable memory, battery level detection, power on reset, and system timers. Read More

Communication Systems & Equipment, Electronic Components & Devices

Wireless Receivers support automotive and consumer applications.

August 4, 2010

Supporting 315, 434, 868, and 915 MHz bands, Models TDA5240, TDA5235, and TDA5225 provide data rate up to 112 kchips/sec with typical sensitivity of -119 dBm for FSK and 116 dBm for ASK. Sigma-delta fractional-N PLL synthesizer provides fine multi-channel resolution of 10.5 Hz. Models TDA5240 and TDA5235 support autonomous receive mode where desired payload is automatically extracted and interrupts can trigger host controller to read payload from FIFO memory. Read More

Communication Systems & Equipment

Miniature IR Receivers feature 2 photodiodes.

November 3, 2009

Series TSOP75xxxW ultra-miniature SMD IR receivers include 2 photodiodes and metal EMI shielding in package with 2.35 mm profile. Lens-less products offer irradiance from 0.3-0.7 mW/m2 over wide angle of ±75°. Operating from supply current of 0.35 mA typical at 3.3 V, units have supply voltage range of 2.5-5.5 V and operate over carrier frequency of 30-56 kHz. They are insensitive to supply voltage and ripple noise and offer immunity against ambient light. Read More

Communication Systems & Equipment, Non-Industrial Products

ISR Video Receiver targets military applications.

June 29, 2009

Packaged in standard military-hardened handheld form factor, Model RF-7800T delivers high-resolution, full-motion tactical video to individual warfighters for real-time intelligence, surveillance, and reconnaissance (ISR). Portable, ground-based remotely operated video enhanced receiver (ROVER) accepts video captured by military's fleet of unmanned aerial vehicles. Operating in 1.71-1.81 GHz L-band, unit also supports 2.2-2.5 GHz S-Band and 4.4-5.8 GHz C-Band. Read More

Communication Systems & Equipment

SMD IR Receiver offers 300 µsec of reaction time.

February 4, 2009

Optimized for sensor and light barrier systems, Compact SMD IR Receiver TSOP5038 is insensitive to supply voltage ripple and EMI noise, and offers low supply current of 0.85 mA typical at 5 V. It offers high fixed gain in all ambient light environments, 0.5 mW/sqm typical irradiance, and supply voltage of 2.7-5.5 V. RoHS 2002/95/EC and WEEE 2002/96/EC compliant unit features photo detector and preamplifier, as well as internal IR filter that suppresses visible light. Read More

Communication Systems & Equipment

SMD IR Receivers offer optimized sensitivity-to-size ratio.

February 3, 2009

TSOP75xxx series features 2 photo detectors and preamplifier in one 3.0 mm-profile package with 2 epoxy lenses designed as IR filter, which has frequency range optimized for reducing emissions from plasma displays. AGC versions include TSOP752xx, compatible with all common IR remote control data formats, as well as TSOP753xx and TSOP754xx, which suppress almost all spurious pulses from energy-saving fluorescent lamps and are respectively compatible with short- and long-burst codes. Read More

Safety & Security Equipment, Controls & Controllers, Communication Systems & Equipment

Receivers support up to 500 wireless transmitters.

February 12, 2008

Equipped in compact unit suitable for residential and small commercial security installations, in-line receivers, models 1100DI and 1100XI allow for wireless capability. Suitable for harsh RF environments, high power receivers, models 1100DH and 1100XH increase coverage by offering greater transmission and higher sensitivity for reliable performance in industrial locations. Models provide two-way, supervised communication using 900 MHz frequency hopping spread-spectrum technology. Read More

Communication Systems & Equipment

IR Receivers suit noisy environments and short burst codes.

February 4, 2008

Available in 5 series and 3 pin configurations, AGC3 IR Receivers offer resistance to ESD, shielding against EMI, and immunity against ambient light, making them suited for remote control, data transmission, and light barrier applications. Units include photo detector and preamplifier circuit, mounted within 3-pin epoxy-encapsulated module. Specified for operation from 2.5-5.5 V with transmission range of 45 m, RoHS-compliant modules consume 0.35 mA and feature carrier frequency of 30-56 kHz. Read More

Communication Systems & Equipment

Infrared Receiver Modules are made for portable systems.

October 29, 2007

Series TSOP85... infrared receiver modules utilize dual lens and photodiode construction to deliver sensitivity and range to remote control, data transmission, and light barrier applications. Surface mountable module offers broad supply voltage range of between 2.7-5.5 V, and 7 standard carrier frequencies ranging from 30-56 kHz. Device is capable of operating with short-burst transmission codes, at data rates of up to 4,000 bps, and measures 3.3 mm high, and 2.74 mm wide. Read More

Communication Systems & Equipment, Electronic Components & Devices

UHF ASK/FSK Receiver ICs suit TPMS and RKE applications.

September 18, 2007

Supplied in SSO20 package, ATA5723, ATA5724, and ATA5728 can be used to cover respective ranges of 313-317 MHz, 432-436 MHz, and 868-870 MHz. Products support Manchester as well as Bi-phase coding signals and provide logarithmic RSSI output. Manufactured using RF BiCMOS process, solutions offer receiving selectivity optimized via integrated image rejection mixer with 30 dB rejection; -113 dBm sensitivity; as well as integrated IF filter, low-phase-noise VCO, PLL, and loop filter. Read More

Communication Systems & Equipment

IR Receiver Modules offer pulse-distance coding up to 35 m.

November 30, 2006

Designed to address class of coding protocols using pulse-to-pulse or presence of pulse timing methods, TSOP18238, TSOP19238, TSOP14838, and TSOP12238 devices are specified for operation at 5 V and feature carrier frequency of 38 kHz. Each incorporates photo detector and preamplifier circuit, mounted within 3-pin, epoxy-encapsulated module with integrated lens. Internal AGC circuit provides immunity against optical noise, while internal metal shield protects against EMI. Read More