Thermo Fisher Scientific
Waltham, MA 02454
Jul 19, 2007 Designed for GC, LC, and elemental analyzers coupled with isotope ratio mass spectrometers, ConFlo IV Universal Interface enables immediate switching between up to 3 sample preparation devices. It includes smartEA(TM) mode, which allows automated pre-evaluation and adjustment of sample gas intensities. Along with flexible, computer controlled auto-dilution of sample and reference gases, software also controls stand-by and start-up of Thermo Scientific TRACE GC and Flash EA modes.

Phoenix Contact
Harrisburg, PA 17111 0100
Feb 27, 2007 Suited for use in shipbuilding and marine industries, PSI-MOS Profibus Fiber-Optic media converters feature conformal-coated printed circuit boards for protection against salt water, moisture, and dust. Devices are approved for use in UL Class 1, Division 2 hazardous locations where volatile flammable materials are normally found and contained, but can become hazardous through abnormal conditions.

KORENIX Technologies
Taipei 231  Taiwan
Nov 27, 2006 Designed to convert 1000Base-T to 1000Base-SX/LX signals, 3301 Gigabit Ethernet Media Converter expands network through gigabit fiber optic connection, extending single mode fiber link up to 20 km. Devices feature LC and SC connector formats in multi- and single-modes, and can be installed stand-alone or mounted on media converter chassis. Supporting packets up to 10 KB, series features auto-negotiation and flow control function on RJ-45 copper port.

Highland Technology, Inc.
San Francisco, CA 94103
Nov 01, 2006 Offered in 850 nm multimode and 1,310 nm singlemode versions, single-channel Model J724 allows fast timing and logic-level signals to be transported via fiber optic levels. Packaging enables E/O transition to be located wherever convenient, and adjustable inputs are compatible with TTL, LVTTL, ECL, NIM, and most other common logic levels. Converter is intended for use with 9/125 micron singlemode fiber, but is also usable with 62/125 micron multimode fiber.

KORENIX Technologies
Taipei 231  Taiwan
Oct 06, 2006 Supplied in IP31-rated, 70 x 30 x 89 mm aluminum case, JetCon1301 Industrial 10/100Base-TX to 100Base-FX Multi-/Single-Mode fiber media converter can operate in switching converter or pure converter modes. Store-and-forward technology, implemented in switching converter mode, filters out abnormal packets to maintain network performance. In pure converter mode, unit only converts signal between copper and fiber port. Solution supports 10/100Base-TX auto MDI/MDI-X and auto negotiation.

B & B Electronics Mfg. Co.
Ottawa, IL 61350
Sep 21, 2006 Available for RS-232 and RS-422/485 data circuits, I-linx stand-alone optical isolators in industrial DIN rail mount cases offer 2,000 V protection. Converters change RS-232 format data signals to RS-422 for increased range, or RS-485 for increased range and multi-drop capability. Model FOSTCDRI converts RS-232, RS-422, or RS-485 to transmit over fiber optic cable, which allows range up to 2.5 miles.

Weed Instrument Co., Inc.
Round Rock, TX 78680
Jul 19, 2006 Designed to multiplex CEMS 4-20 mA and 0-10 Vdc output signals at coal-fired power stations, Fiber Optic Converters monitor sulphur dioxide, nitrogen oxides, and particulate matter. Providing bi-directional communications, Series 2Mxx sends and receives up to 8 analog or digital signals over pair of fiber optic cables. Conversion of analog signals to fiber overcomes application issues such as EMI/RFI, lightning strikes, and ground loop problems.

Pepperl + Fuchs, Inc.
Twinsburg, OH 44087 2245
Mar 29, 2006 Featuring one-part construction, VAZ-2T1-FK AS-Interface Flat-to-Round-Cable Converter is suited for use in narrow and low-profile cable channels as well as other space-critical locations. Product installs in under 1 min in most applications and is designed for use where AS-Interface and 24 Vdc external power need to be on one M12 connector. Products are suited where AS-Interface drives with motor starters are used and for connecting AS-Interface sensors.

B & B Electronics Mfg. Co.
Ottawa, IL 61350
Feb 17, 2006 Elinx EIR and EIS series enable users to convert to and from fiber-to-copper installations through hostile RFI/EMI environments. They can also extend distances up to 1.2 miles with multi mode fiber and up to 12.4 miles with single mode fiber. Rugged EIR series comes in industrial DIN rail-mount package, while commercial EIS models come in desk-, wall-, or rack-mountable packages with power supply. Both versions offer options to convert 10/100Base TX signals to 100Base FX.

Highland Technology, Inc.
San Francisco, CA 94103
Jul 21, 2005 Electrical-to-Optical Converter, Model J720 and Optical-to-Electrical Converter, Model J730 convert logic levels to fiberoptic media for low-noise transport up to kilometers, with link jitter below 10 ps rms. Model J720 is powered by logic-level input, and Model J730 requires +12 V supply, user-furnished or from wall-plug power adapter. Model J730 provides digital logic output with risetime below 750 ps. Both use ST-connectorized 62/125 micron multimode fiber.

Artesyn Technologies
Framingham, MA 01701
Jul 01, 2005 Occupying board area of 2.14 in.², open-frame PTHxx040W series features output voltage adjustment and Auto-Trackâ„¢ power sequencing. Model PTH12040W has output current rating of 50 A and 8–14 V input voltage range, while PTH04040W has 60 A rating and input range of 2.95–5.5 V. Series is Point-of-Load Alliance (POLA)-compliant and employs switching frequency of 1.05 MHz to achieve full load conversion efficiencies to 96%. Both models deliver up to 250 W.

Phoenix Contact
Harrisburg, PA 17111 0100
Nov 04, 2004 Model PSI-MOS transmits fiber optic data for serial communication interfaces and bus systems. By converting electrical copper-based signals to glass or polymer fiber technology, it allows isolation of Interbus, Profibus, Modbus, DeviceNet, CANopen, RS-232, and other RS-485 networks. Onboard diagnostics provide information about signal quality on fiber optic path. If failure occurs, each module disconnects affected bus segment to prevent transmission of corrupted data.

Terahertz Technologies Inc.
Oriskany, NY 13424 4301
Nov 02, 2004 LTX-5510 Electrical/Optical – Optical/Electrical converter pair digitizes analog input signal to 12 bit precision, along with 4 auxiliary digital inputs, and transmits data over Gbit fiber optic link. LTX-5510R receives transmitted data and reconstructs 5 signals at far end of link. Transmitter has selectable input ranges, ±1 or ±5 V, and input impedances may be set to 1 Megohm or 50 ohm. Overall system bandwidth is dc to 12.5 MHz.

Advantech Automation Corp.
Cincinnati, OH 45240
Aug 04, 2004 Model ADAM-4542+ converts single-mode fiber optic signals to RS-232/422/485 serial signals. Aimed at long-distance communication applications such as intelligent transportation systems, it offers transmissions up to 15 km and wavelengths at 1,310 nm. By providing fault detection on main connection between 2 modules, communication can be automatically and seamlessly switched to secondary connection.

AMETEK, Advanced Measurement Technology, Inc.
Oak Ridge, TN 37831-0895
Jul 27, 2004 Available in 2 versions, DPM-PCI Interface makes ORTEC Multi-Channel pulse-height Analyzers (MCAs) compatible with latest personal computers (PCs) by converting MCAs with obsolete ISA-bus interface to PCI-bus interface prevalent on newer PCs. Versions include one to upgrade existing ORTEC MCAs to PCI interface, and one to provide PCI interface for new MCA. Former comes with drivers needed to update existing MCA emulator software.

CyberResearch, Inc.
Branford, CT 06405 2932
Jul 09, 2004 Both DVE 1000 video extenders and CLE 500 camera extenders use matched converters to switch between electronic and optical signals. DVE 1000 units allow monitors or projectors to be located up to 3,300 ft away from host computers, while CLE 500 models allows distances up to 1,640 ft from camera to computer. Transmitters and receivers are connected using CFSM simplex fiber-optic cables, while monitors and computers are connected with VESA DVI-D cables.

Contemporary Control Systems, Inc.
Downers Grove, IL 60515
Jun 07, 2004 In full-duplex mode, EIMC-100T/FCS Ethernet Converter extends fiber distance to 15 km, making single-mode fiber connection via SC-style connectors. Design reduces installation time and improves data flow, and features PnP technology, miniature size, DIN-rail installation, and choice of low-voltage ac or dc power sources.

Electro Standards Laboratories
Cranston, RI 02921
Mar 25, 2003 QuickSwitch Model 5191, 8-Way Fiber Optic Remotely Controlled Switch/Converter acts as signal source and prevents optical signal loss. Fiber optic-to-twisted pair conversion is built-in, and unit allows access to any one of eight fiber optic network ports from one computer. Product offers pushbutton switching and LED display for switch position and fiber link presence. Network ports are 1300 nm 100 Mbps ST or SC Duplex multimode fiber optic ports.

Phoenix Contact
Harrisburg, PA 17111 0100
Mar 12, 2003 Modular, DIN-rail-mounted PSI-MOS-DNET system consists of fiber-optic converters that allow complete isolation of DeviceNet networks as well as full redundant operation of fiber communication lines and power supply. Immune to EMI, RFI, and transient surges, system allows use of base module for point-to-point configurations for line structures and extended bus drops. Offered with fiber-optic line monitoring and diagnostics, units display optical power budget via LED bargraph.

Electro Standards Laboratories
Cranston, RI 02921
Feb 18, 2003 QuickSwitch 4185 Fiber Optic Switch/Converter allows user to access 2 separate fiber-optic 100 Base FX ports from 100 Base TX Fast Ethernet port. Fiber optic/twisted pair copper conversion is built in and unit is compliant with 802.3u 100 Base TX/FX standard. Ports A and B are 1300 nm, SC Duplex, Multimode, 100 Base FX fiber optic ports. COMMON port is 100 Base TX Fast Ethernetport. Front-panel button changes switch position and LEDs display switch-position status.