Cleveland Vibrator Co., The    Cleveland, OH 44113
Dec 27, 2011 Offering choice of optional electromagnetic jogger table or standard dual outboard rotary electric drives, HK Laboratory/Pilot Sieve Towers feature vibratory design that enables sieve analysis of product samples. Towers accommodate up to 8 full height sieves or set of 16 half frame sieves for dry or liquid slurry materials. Units are available in 8, 12, or 17 in. diameter sieve sizes down to 20 micron. With ultrasonic vibration upgrade, devices support mesh sizes down to 10 micron.

L-Com, Inc.    North Andover, MA 01845
Dec 02, 2011 Available for DB9, DB15, and DB25 D-subminiature connectors, Y Adapters/Splitters each come with 1 male to 2 female connectors, wired 1:1 to evenly split signals. Units are fully shielded and have 30 µin. gold plating on contacts for repeated mating cycles. Made of rigid PVC, light gray molded casing maximizes longevity.

Green Turtle    Charlotte, NC 28217
Nov 10, 2011 Used in fats, oils, and grease (FOG) management, Proceptor®PDI engineered gravity grease interceptor features flow design and tank shape that promote regulatory compliance. Solution is available as hydro mechanical grease interceptor certified by Plumbing and Drainage Institute to 100 gpm and grease holding capacity of 200 lb. Able to serve several sinks, dishwashers, floor drains, and food disposal devices, system installs above ground, in kitchen/basement, in floor, or outside.

Kason Corporation    Millburn, NJ 07041
Nov 09, 2011 Centri-Sifter® model YOB-SS features cantilevered shaft with 2 externally mounted bearings between screening chamber and motor drive, allowing all components to slide freely from shaft end for accelerated cleaning, screen changes, and inspection. System comes in configurations for gravity-fed applications or continuous operation in-line with dilute-phase pneumatic conveying systems, with screen cylinders of Nylon monofilament, woven wire, perforated plate or wedgewire screen.

Universal Separators, Inc.    Madison, WI 53705
Oct 10, 2011 Designed to clean contaminated machine tool sumps, Sump Caddy can be moved between machines to clean coolant as needed. Recycling system separates and removes tramp oils and also filters small fines from coolants. Portable unit includes mild steel, 60 gal processing tank with coalescing technology. Functionality helps extend life of machining coolants, improve tool life, and reduce odors associated with contaminated coolants.

GOO-FAR    Istanbul   Turkey
Oct 04, 2011 Featuring 2 inlet ports, GOO-FAR Water Separator and Fuel Filter ensures supply of 99.99% water-free light diesel fuel to fuel injection system and engine. Product keeps fuel tank, engine, and injectors clean via 30 micron particle separation, promoting fuel combustion and fuel efficiency while reduce emissions and exhaust temperatures. Cleanable filter (cartridge) is made of chemically coated stainless steel and does not require replacement for up to 2 years.

Eriez Magnetics    Erie, PA 16514
Sep 29, 2011 Used in vacuum and pressure pipelines, PN Metal Separators remove metal contaminants from pneumatically conveyed materials, plastic pellets, and regrind. Contaminants, even those encapsulated in pellets, are removed via reject mechanism that operates reliably at conveying speeds to ~4,000 fpm without interrupting flow. Modular design enables flexible adaptation to different conveying methods, and options are available to accommodate high temperature, abrasive, and powdery bulk materials.

Kason Corporation    Millburn, NJ 07041
Sep 20, 2011 Vibroscreen® K72-1K-SS (72 in.) discharges oversize particles 360° around periphery of External Kascade circular screening deck instead of through conventional discharge spouts. As material is fed onto center of screening deck, on-size particles pass through screen and funnel to lower discharge chute, while oversize particles flow outward in spiral pattern into high capacity discharge spout. Applications include removal of fines from products such as plastic pellets, cereal, pet food, etc.

Celeros Separations    Foxborough, MA 02035
Sep 08, 2011 Employing tubular bowl with working volume of 40 L, Model APD-250 is capable of generating up to 20,000 x G of separating force and processing bioreactor harvests up to 10,000 L in single shift. Large-scale production centrifuge utilizes Automatic Piston Discharge system to completely transfer separated solids from bowl without operator intervention or excessive loss of centrate.

Mini-Circuits    Brooklyn, NY 11235
Sep 01, 2011 Capable of operating up to 15 W, model QCS-83+ is 2-way 90° power splitter with 4,000-8,000 MHz range and typical unbalance of 0.8 dB and 4°. Microwave RF/IF power splitter combiner, supporting nearly octave band in miniature EIA-0805 form factor, features LTCC construction, which lends to effective use in transmit or receive paths.

SWECO®, Div. of M-I L.L.C.    Florence, KY 41022
Aug 19, 2011 Incorporating vertically mounted motor that induces sifting motion across screen plate, LA Low Profile Separator is suitable for sifting flours and starches. Frame is mounted on rubber isolators rather than springs used in conventional separators. Horizontal, high G motion maximizes capacity of undersize product passing through screen while allowing oversize material to exit separator. Featuring sanitary construction, separator meets needs of food/beverage and pharmaceutical industries.

Industrial Magnetics, Inc.    Boyne City, MI 49712
Jul 26, 2011 Designed for use with abrasive products in pneumatic transfer applications, magnetic separation solution has housing comprised of 2 door-mounted magnetic plates positioned on opposing sides of stainless steel tube matching existing diameter of processing line. This design maintains existing flow rate, eliminating wear points within magnetic housing. Dual-magnet design reaches through entire product stream and captures metal contaminants from flow.

Kason Corporation    Millburn, NJ 07041
Jul 19, 2011 Intended for food, dairy, pharmaceutical, and chemical applications, Centri-Sifter® features 3-bearing shaft that cantilevers for removal of internal components. External roller bearings located at motor end of shaft and on hinged cover at discharge end provide maximum support and vibration-free operation under heavy loads. Equipped with Clean-In-Place Spray Balls for rapid sanitizing using steam or cleaning solution, stainless steel unit is finished to industrial, 3-A, FDA, and BISSC standards.

Eriez Magnetics    Erie, PA 16514
Jul 12, 2011 Using ballistics to separate iron-rich ferrous from mixed metals and waste material in post drum magnet flow, Shred1(TM) Separator delivers 3 distinct fractions. Fraction 1, representing 60-80% of flow, contains less than .2% copper and does not require picking. Fraction 2 represents 20-30% of flow and contains mostly mixed metals, copper, and aluminum with steel housings or cores. Containing 5-7% of flow, Fraction 3 consists of heavy steel objects and light material, such as fluff and rubber.

SWECO®, Div. of M-I L.L.C.    Florence, KY 41022
Jul 12, 2011 Available in 48 and 60 in. diameters with 5 hp motor, Super MX Separator delivers forces as high as 10 G and is suited for separating solids from liquids or segregating dry materials into various sizes. Machine utilizes conical construction rather than flat plates, which creates rigid geometric structure. Totally enclosed weight guard prevents reach-in injuries, while open base design allows for cleaning underneath unit, preventing dirt and product build-up.

SWECO®, Div. of M-I L.L.C.    Florence, KY 41022
Jun 21, 2011 Supplied in open-manifold or Packed-Vessel configuration, SWECO® Hydrocyclone System provides fine particle separation for wet processing. Manifolds utilize 2, 4, 5, or 10 in. diameter cyclones while Packed Vessels contain either 1 or 2 in. diameter cyclones. Both configurations can process feed rates from 10-3,000 gpm, depending on size and number of hydrocyclones installed in system. Reliable operation only requires consistent feed at steady pressure.

Magnetic Products, Inc.    Highland, MI 48357
Jun 09, 2011 Utilizing neodymium Rare Earth magnets, Eco-Mag(TM) removes ferrous and para-magnetic contamination from fluids and is particularly effective with machine tool oils, coolants, and hydraulic fluid machinery systems. Eco-Mag does not use consumables, and removed contamination can be recycled, eliminating disposal costs.

Nilfisk Industrial Vacuums    Morgantown, PA 19543
May 31, 2011 Placed upstream from Nilfisk CFM-brand vacuum, Nilfisk CFM Immersion Separator safely traps and retains dangerous Group E dust particles in neutralizing fluid bath. Unit is constructed of low-sparking materials and grounded components with grounding strap for added safety. Separator includes drain valve, antistatic wheels, and sight level tube to monitor liquid levels. Coalescent filters prevent passage of fluid droplets that have been agitated by working air from passing back to vacuum.

Supercritical Fluid Technologies, Inc.    Newark, DE 19711
May 10, 2011 Able to perform supercritical fluid extractions in single or dual 10 L sample vessels with single or dual separators, SFT-NPX-10 pilot scale supercritical extractor facilitates transition from laboratory scale equipment to production processing systems. Coriolis mass flow meter delivers mass flow measurement precision, and pneumatic CO2 pump with waterless pre-chiller maximizes pumping efficiency. Optional RIO programmable automation controller upgrade is available.

Palmer Manufacturing & Supply, Inc.    Springfield, OH 45504
May 10, 2011 Using blower and heavy-duty steel fluid bed, UHT-Series cools sand from over 1,000°F to as low as 120°F at rates up to 40 tons/hr. Temperature of incoming sand is monitored, and necessary amount of properly tempered water is metered into linear stainless steel cooling bundle to meet discharge set point. In addition to Ethernet-enabled, PLC-based control system, features include 2 dust collection take-offs as well as shutdown and alarms for water flow/temperature and pressure.