Chemical Processing & Waste Management
(Showing headlines 1541 - 1560) << 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 ...
Structural Acrylic Adhesives bond to variety of materials.
Somerset, NJ 08873
May 11, 2005
Formulated for bonding plastics, metal, composites, ceramics, wood, and glass, Structural Acrylic Adhesives cure to handling strength within minutes and achieve working strength within 30 minutes. Products are available as separate adhesive with brush on initiator or as no-mix bead-on-bead acrylic. Non-flammable adhesives are resistant to impact, shear, and peel loads, making them suitable for high-stress applications.
Demulsifiers perform clean separation of crude oil.
GE Advanced Materials
Wilton, CT 06897
May 10, 2005
Able to reduce salt content of separated crude, Silbreak(TM) silicone demulsifiers produce lean, sharp interface between crude and water phases. They perform clear separation of 2 phases, such as water and oil, in mineral oils, silicone oils, or crude oils. Use of products results in dryer crude oil and cleaner water.
Drying Systems remove water from hydrophilic foams.
Radio Frequency Co., Inc.
Millis, MA 02054
May 10, 2005 Macrowaveâ„¢ Foam Drying Systems heat and uniformly dry hydrophilic foams evenly throughout entire thickness. Systems apply radio waves to foam webs or buns up to 4 ft thick at frequency of 40.68 MHz, which rapidly remove water without surface discoloration, cupping caused by non-uniform shrinkage, and surface hardening. They can also dry water-based glues in construction of foam laminations up to several feet thick.
Thermodynamic Disc Trap offers thermostatic air venting.
Charlotte, NC 28273
May 10, 2005
Cast steel P46SRN, suited for steam mains, tracers, and coils, features built-in screen, optional blow down unit, and stainless steel internals. Design provides inline access to internal parts, enabling unit to be serviced without removing body from installation. Available in ½, ¾, and 1 in. sizes in NPT and SW, product uses lapped disc for steam-tight seal without air binding. Air jacket insulates pressure chamber, and bimetal air vent ring automatically vents air.
TPE Alloys are suited for replacing silicone and PVC.
McHenry, IL 60050
May 09, 2005 Featuring water-clarity and heat resistance, VERSAFLEX® CL 2200 TPE (thermoplastic elastomer) alloys are supplied as injection-moldable pellets with 42 and 50 Shore A hardness. They offer bite and tear resistance, making them suitable for infant care and kitchenware products that require boiling and/or cleaning in hot dishwashers. Also suited for toys and tubing, they can be used in overmolding applications with polypropylene substrates.
High-Pressure Filters reduce hydraulic fluid contaminants.
EP NTZ Micro Filtration
Inkster, MI 48141
May 09, 2005
Made of extruded aluminum, ALH series uses bypass filtration with radial micro depth filter element to capture 99.97% of particles 2 microns and larger while also absorbing water or water-linked acids. Manifold incorporates compensating valve that permits 1-2 Lpm flow rate without causing pressure drop in original system. Available in 4 filter sizes, series uses max pressure of 210 bar.
Piston Pumps are suited for heavy-duty applications.
Thomas Products Division
Sheboygan, WI 53081
May 06, 2005
Offered with continuous-duty, single- or 3-phase motors from ¼-¾ hp, GH Series articulating piston compressors and vacuum pumps feature oil-less design with permanently lubricated and sealed bearings, cast iron cylinders, and stainless steel valves. Pressure models include check and safety relief valves as well as inlet filters, while vacuum models include exhaust mufflers. Pumps deliver air flow to 5.2 cfm, pressure to 175 psi, and vacuum to 27.5 in. Hg.
Valve Lubricant and Sealant resists effects of chemicals.
Dow Corning Corp.
Midland, MI 48686 0994
May 04, 2005 Dow Corning® 111 heavy-consistency, dimethyl silicone compound maintains serviceable consistency from -70 to +400°F. Acceptable as release agent under FDA 21 CFR 175.300, it carries NSF 51 and NSF 61 approvals. Product can be used as lubricant for rubber and plastic O-rings, water softener and faucet valves, and electronic and ignition systems. It may also be used as sealant in transformer gaskets, equipment enclosures, and equipment subject to harsh environments.
Venturi Vacuum Pumps feature micro-minature design.
Anver Corp. - Anver.Com
Hudson, MA 01749
May 04, 2005 Lightweight JV venturi vacuum generators provide milli-second attach-and-release and designed for pick-and-place systems. Weighing 0.63 oz, they can be mounted at pick-up point and accommodate several types of suction cups. Pumps can be controlled using compressed air supply valves and components, enabling designers to use pneumatic controls rather than vacuum controls. Pumps achieve 26 in. Hg vacuum with 0.50 or 0.74 scfm flow rate.
Flame Retardant Piping meets ICC fire code.
Paris la Defense Cedex F92091 France
Apr 29, 2005
Kynar® 740-02 polyvinylidene fluoride (PVDF) thermoplastic piping meets flame and smoke requirements developed by International Code Council® (ICC) for material use in building plenums. Available with 0/10 or 10/35 ASTM E84 rating, product exhibits resistance to most chemicals at room temperature in acid waste drainage applications and can handle elevated temperatures to 150°C. Performance polymer is also resistant to abrasion.
Peelable Lid Stock suits thermoformed PET trays.
Cary, IL 60013
Apr 28, 2005
Flexi 6818 Lamination features heat-seal coated polyester coupled with metalized, white oriented polypropylene. It is available with 2-sided print and with 100% opacity. Copy on reverse side will not show through front facing and vice versa. Flexi 6818 can be sealed around face of tray, leaving corner exposed to grab and pull for product access. Puncture resistant film will not tear upon opening and is suited for consumer goods and solid or semi-solid products.
Sorbent Panel Assemblies trap odors, gases, and particulate.
Riverdale, NJ 07457
Apr 27, 2005
CamsorbT CF4A adsorber modules are suited for commercial, industrial, and medical facilities where control of gaseous contaminants or odors may be of concern. Each unit uses 12 Camsorb CF 1 in. panels filled with loose-fill or application-specific sorbent media. Sorbent section is sandwiched between 2 particulate filter frames that allow installation of various combinations of prefilters and ASHRAE grade final filters. Assemblies may be stacked up to 6 units high.
Disposable Absorbent Pads are environmentally friendly.
Complete Environmental Products, Inc.
Pasadena, TX 77503
Apr 21, 2005 OilZapâ„¢ Pads feature cellulose core that absorbs oil, oil-based products, and water, and have polypropylene backing to prevent liquids from leaking through. One pad absorbs ½ quart of oil, and pads can withstand hot oil up to 210°F. Applications include under vehicles, machines, equipment, and bilge of boats, as well as absorbing spills and wiping oily hands and tools.
Pump covers wide range of pressure/vacuum applications.
Thomas Products Division
Sheboygan, WI 53081
Apr 21, 2005
Series 1207 WOB-L® Piston pump features oil-less, non-lube piston and cylinder for long life and clean air flow. Features include permanently lubricated bearings, SS valves, hardcoated aluminum cylinder, and PFTE piston seals. Pumps, powered by capacitor start ac motors, deliver flow up to 4.3 cfm, pressure to 125 psi, and vacuum to 28 in. hg. Applications include packaging equipment, plasma welders, business machines, pneumatic tools, and respirators.
Port Splitter expands communications capabilities.
Milwaukee, WI 53204
Apr 19, 2005
Used with existing controllers, RS-232/DF1 port splitter connects to DF1 full-duplex port to allow simultaneous communication with local network and operator interface. Control users with one DF1 full-duplex port can use splitter to create one fullfunction port for 2-way communication between controller and local network. Primarily designed to run programming terminal or HMI, second port is respond-only.
Submersible Level Transducers are protected by vent filter.
Pressure Systems, Inc.
Hampton, VA 23666
Apr 18, 2005
Vented gage KPSI(TM) transducers come with Series 810 SuperDry vent filter, which provides maintenance-free moisture protection. Designed for high-humidity environments where water vapor may condense in vent tube, filter prevents formation of liquid column and guards sensitive transducer electronic components from mildew, corrosion, rust, and other forms of deterioration. Indicating desiccant turns from blue to pink as filter's drying capacity is diminished.
Sheet Fanners use magnets to reduce handling time.
Bunting Magnetics Company
Newton, KS 67114 0468
Apr 18, 2005 Sheet Fanners, designed for safe handling of sheet stock stacks, utilize non-electric permanent magnets to automatically fan sheets apart. By eliminating chance of jamming doubles into production equipment, product enables operators to safely handle one sheet at a time. All-stainless-steel units are self-contained and can be ganged to handle larger sheets. They come with carrying handles for portability and holes for permanent mounting.
Modeling Resin helps visualize details.
Minneapolis, MN 55344 2020
Apr 14, 2005
Designed for Eden333 PolyJet system, VeroBlue(TM) acrylic photo-polymer resin allows users to see more detail than transparent model allows, and achieves resolution of 16 microns. Opaque, blue-colored material helps make models look more like injection-molded part without need for paint. Changeover steps from transparent resin to VeroBlue take less than 15 min, and require replacing material cartridge and following automated wizard set-up process.
Cable Compound offers low-smoke, low-flame properties.
Somerville, NJ 08876
Apr 12, 2005
CyberShield flexible PVC compound for plenum cable offers low-smoke, low-flame, low-temperature properties. Benefits include flexible durometer of 95 Shore A and temperature flexibility to -30°C. It meets requirements of UL 910 Steiner Tunnel for low-smoke and low-flame properties.
Screen Protectors protect portable and hand devices.
Silver Cloud Mfg. Co.
Millville, NJ 08332 5002
Apr 11, 2005 DURALAN II screen or lens protectors protect displays on touch screen input devices, including pen-based touch systems and POS terminals. With thickness of .007 in. typ, products have hard-coated, anti-glare surface. Adhesive strip, screen-printed around perimeter, can be removed without leaving residue. Made from polycarbonate in custom sizes and shapes, products offer chemical- and scratch-resistance and are also available with anti-reflective surfaces.
(Showing headlines 1541 - 1560) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116