Herbold Meckesheim USA
Smithfield, RI 02917
May 09, 2008 Suitable for dry or wet operation, horizontally fed SB Series granulate containers made of Polyethylene Terephthalate (PET) and other recyclable plastics. Horizontal feeding screws force materials from hopper to adjacent cutting chamber at steady, even pace instead of depending on materials to fall directly into blades, which reduces fines and dust. Granulators can also be used for secondary size reduction of pre-shredded plastics.

Kason Corporation
Millburn, NJ 07041
May 08, 2008 Model K30-2-SS 30 in. dia circular vibratory screener integrated with Model K40/48-1FBD-SS 40 in. dia circular fluid bed dryer remove off-size particles while dewatering and drying on-size material. System removes up to 50 gpm of water and dries up to 700 lb of on-size particles per hr. Screener is equipped with imbalanced-weight gyratory motor that vibrates screening chamber, which is suspended on springs. Circular fluid bed dryer requires only one air inlet and outlet.

Kason Corporation
Millburn, NJ 07041
May 07, 2008 Vibroscreen Gap-Free Classifier offers non-metallic material contact surfaces and quick-cleaning features designed to eliminate contamination of ultra-pure products. This 60 in. dia unit is configured with 3 screening decks for removing oversize particles and de-dusting material, while separating on-size material into 2 size fractions. Other features include gap-free screen frames, quick-release U clamps, radius corners, domed lid, and continuous ground and polished welds.

SKF USA Inc.
Kulpsville, PA 19443
May 07, 2008 In conjunction with large air compressors and systems, SKF® SFD dryer system dries compressed air for pneumatic applications directly from tank. Compact device incorporates 3-in-1 system to remove oil, contaminants, and moisture, operating up to 175-200 psi. Installing on wall or directly to compressor top plate, it can be supplied for 12, 24, and 120 Vac, or fully pneumatic requiring no electrical connection. Basic flow rates up to 40 cfm can be achieved.

JMD Mfg., Inc.
Framingham, MA 01701
May 07, 2008 Offering alternative to shredders, low-noise Nano-DeCopier provides decopying and destruction of sensitive and confidential documents. Unit reduces paper to approximately 0.25 x 0.25 in. pieces after 3-minute cycle, which is impossible to reverse. Product uses non-toxic, green D-1200 cleaning mixture as decopying fluid, which is also available in gel/stick form.

West Development Group
LaGrange, OH 44050
May 07, 2008 Designed for use on sprayed-in-place polyurethane foam, HSS 535 and HSS 540 R2R(TM) one-component coatings are tack-free within 1-2 hr and cure at normal temperatures in 2-6 hr by reacting with moisture in air, forming flexible moisture-free seal. Because coatings are solvent-free, they are environmentally friendly while providing same functionality as petroleum-based roofing materials. Both passed ASTM E108 flame spread test and obtained UL Class A fire rating.

RTP Co.
Winona, MN 55987
May 06, 2008 Featuring consistent mechanical properties across hardness spectrum of 50-75 Shore A, Series RTP 6042 thermoplastic elastomer compounds bond variety of rigid substrates including PC, ABS, PC/ABS, PC/PBT, PC/PMMA, and RTPU resins. Compounds are suited for rugged electronic devices with over-molded designs where optimal tensile and shear strength as well as abrasion resistance is required.

Dekker Vacuum Technologies, Inc.
Michigan City, IN 46360
May 05, 2008 Consisting of 2, 3, or 4 simplex oil-sealed liquid ring pumps, VmaxVFD systems are microprocessor-controlled and conserve energy by automatically adjusting pump speed to match varying vacuum demand. This also eliminates frequent stop-starts and promotes stable vacuum levels. Separately located variable frequency drive (VFD) main control panel provides single location for system control and aggregating alarm outputs for remote monitoring.

SABIC Innovative Plastics
Pittsfield, MA 01201
May 05, 2008 Optimized for injection molding and plating processes, special grades of Cycoloy polycarbonate/acrylonitrile-butadiene-styrene (PC/ABS) resin and Cycolac ABS resin help automakers incorporate chrome details into their designs. Cycoloy CP8930 (high heat), Cycoloy CP8320 and MC1300 (medium heat) resins, and Cycolac MG37EP resin feature impact modifier that ensures consistent adhesion of chrome layer and are formulated for minimal stress to ensure uniform plating behavior.

Franklin Miller Delumper Mixer Div.
Livingston, NJ 07039
May 02, 2008 Designed to be used in open or closed systems, DELUMPER® 1075 LP reduces hard or soft, heat-sensitive, sticky, or wet agglomerates and lumps without degrading material or causing rise in temperature. Low-friction cutting action handles sludge cake, agglomerated chemicals, plastics, fats, waxes, or solid waste. Extended cutting teeth rotate completely through heavy bar cage, self-clearing slots with each rotation, and output sizes are adjustable by changing comb speed.

Bel-Art Products
Pequannock, NJ 07440 1920
May 02, 2008 Spinbar Magnetic Sink Strainer has 4 magnets in each corner that keep Spinbar Magnetic Stirring Bars from going down drain and long slits in sides and skirt that allow fluids to drain rapidly. Available in blue or green, chemical resistant unit has flat edge on one side that allows it to be placed close to sink wall. Four legs anchor strainer in sink drain and prevent it from being dislodged by flowing liquid.

Franklin Miller Delumper Mixer Div.
Livingston, NJ 07039
May 01, 2008 AUTORAKE® Model 1400 is front cleaned, hydraulic bar screen with design that coordinates motion of mobile rake comb, which travels up and down driven by hydraulic motor and sprocket. Unit can be installed in new or existing channels and configured with auxiliary lift conveyors, dewatering equipment, and grinders to meet any requirement. Available in stainless or carbon steel, AR 1400 is suited for severe, explosionproof, corrosive, or humid environments.

Gardner Denver
Quincy, IL 62301
May 01, 2008 Offering 2-stage diaphragm mechanism with ultimate vacuum to 1.5 Torr, Welch® VARIFLOW(TM) Vacuum Pumps can be used for full chemical- and standard-duty operation in OEM and laboratory applications. Chemical Duty Model 8115D-20 uses PTFE heads/diaphragms and FKM valves, while Standard Duty Model 8115D-25 uses aluminum heads and EPDM diaphragms/valves. All models use 24 V brushless dc motors with maximum power consumption of 85 W and can restart under vacuum.

Dampney Co., Inc.
Everett, MA 02149
Apr 30, 2008 Thurmalox® 8886 Series delivers long-term protection in weathering conditions and creates barrier against attack from glycol cooling agents and synthetic lubricants at temperatures up to 450°F. Available in clear, black, and custom OEM colors, these 2-component silicone copolymer coatings can be applied by conventional and airless, HVLP, HTE, or assisted airless spray equipment. Coatings adhere to clean, smooth steel, copper, and aluminum substrates.

Sto Corp.
Atlanta, GA 30336 5609
Apr 30, 2008 Suited for new construction or renovation, StoCreativ® Granite acrylic-based interior and exterior wall finish is trowel-applied and comes in 10 colors. Use of this product, which is compatible with Sto Classic Wall Claddings (including Sto Classic NExT®), helps incorporate natural looks and colors in finished walls.

Gore, W. L., & Associates, Inc., Sealant Technologies Group
Elkton, MD 22222
Apr 29, 2008 GORE® Cooling Filters include microporous membrane that allows cool, clean air to flow into cabinet while filtering out harmful contaminants such as dirt, dust, and sand. Expanded PTFE membrane has 99.0% particle filtration efficiency at 0.3 µm level. Available in either lightweight or anodized aluminium frame, filters are suited for wireless base stations, MCPAs, base band units, power cabinets, switching systems, and other outdoor electronic enclosures.

DuPont Co., Packaging & Industrial Polymers
Wilmington, DE 19898
Apr 28, 2008 Offering alternative to petroleum-based products, DuPont(TM) Biomax® TPS thermoplastic starch consists of sheet rock that contains 85-90% renewably sourced content for thermoformed trays and articles, and resins for injection-molded parts and containers. With up to 35% renewably source content, Biomax® PTT injection moldable resin is suitable for injection-molded containers, cosmetic packaging, and other parts where polyesters are used.

Security Engineered Machinery Co., Inc.
Westboro, MA 01581
Apr 23, 2008 Capable of accepting stacks up to 1,000 sheets at one time, Model 1201PF shredder accepts paper up to 12¼ in. wide, and can operate continuously without overheating. Bypass slot allows single sheets to be fed manually without interrupting automatic feeder, while cutting head reduces paper to crosscut ¼ x ½ in. shreds. Measuring 20 x 20 x 46 in., it is suited for office use, and comes with automatic stop/start/reverse/shutoff and LCD status panel.

Westfall Mfg. Co.
Bristol, RI 02809-0007
Apr 23, 2008 Used for blending ethanol and other additives into gasoline and other fuels, Static Mixer is heavy-wall 316 SS fixed plate which features orifice pattern that mixes by combination of alternate vortex shedding and intense shear zone turbulence to achieve greater than 98% dispersion within 10 diameters downstream. Designed to fit inside mating flange bolt circle of any piping system, mixer is available in sizes from ½ to 30 in. dia and features Flexitallic® high-pressure gaskets.

Henkel Loctite Corporation
Rocky Hill, CT 06067
Apr 18, 2008 Curing tack-free within seconds, Loctite® 3974(TM) permanently bonds materials with differing coefficients of thermal expansion and accommodates substrate expansion/contraction. Single-component acrylic adhesive cures upon exposure to UV or visible light and can be used on glass, thermoplastic, and metal assemblies for medical device bonding, potting, and sealing applications. Characteristics include A70 Shore hardness and 100% elongation.