Master Bond, Inc.
Hackensack, NJ 07601
Jan 31, 2005 Cured at room or elevated temperatures, 2-component EP21TDCHT-1 has temperature range serviceability of -100 to +400°F. Compound serves as electrical insulator with volume resistivity of 10¹⁴ ohm-cm. Epoxy adhesive/sealant is resistant to vibration, impact, and thermal shock as well as exposure to water, oils, and organic solvents. It has 70 Shore D hardness, 3,000+ psi tensile strength, and 175,000 tensile modulus.

TAH Industries, Inc.
Robbinsville, NJ 08691 1603
Jan 21, 2005 Universal 2-component adhesive cartridge fits in standard caulk gun and is offered in 2:1 ratio pack. Cartridge stores one component of adhesive in front of the other and both are extruded through cartridge outlet into static mixer simultaneously. Unit maintains accurate volumetric ratio and eliminates bulging or expansion of cartridge. The 2:1 ratio contains 177 ml of usable material.

Henkel Loctite Corporation
Rocky Hill, CT 06067
Jan 07, 2005 Hysol 3323, 3327, and 3329 are dam-and-fill products for encapsulation of wire-bonded dies used in Smart Card ICs. Used to form dam, high-viscosity Hysol 3323 has thixotropic nature and glass transition temperature (Tg) of 155°C. Hysol 3327 and 3329 are low-viscosity materials used for fill process. Coefficient of thermal expansion is 45 ppm below Tg and 130 ppm above Tg. Curing time enables max of 10,000 UPH, with no post-cure requirement.

Acoustical Solutions, Inc.
Richmond, VA 23228
Jan 06, 2005 Sound Sealant achieves and maintains specific STC (Sound Transmission Class) value of wall partition systems. Non-flammable, latex-base product is permanently flexible and adheres to wood or metal studs, concrete, gypsum board, AudioSeal Sound Barrier, and other building substrates. Formulation is non-drying, non-hardening, non-staining, and non-migrating. It comes in 29 oz cartridge that covers ~40 linear feet with 3/8 in. bead.

Master Bond, Inc.
Hackensack, NJ 07601
Dec 09, 2004 Featuring thermal stability, 2-component EP21ARHT-1 is 100% reactive and does not contain any solvents or diluents. It has 2:1 mix ratio by weight and cures at room temperature. Exhibiting minimal shrinkage upon cure, product does not sag or drip on vertical surfaces. Designed to withstand thermal shock and abrasion, it adheres to metals, glass, ceramics, cements, woods, vulcanized rubbers, and plastics. Operating temperature range is -60 to +350°F.

Dow Corning Corp.
Midland, MI 48686 0994
Nov 18, 2004 Combined with pre-qualified, turnkey dispensing process, DOW CORNING® SE 4451 is designed to meet heat-management needs of electronic power devices. It exhibits thermal conductivity of 3W/mk @ 25°C and viscosity of 32,000 cps, which facilitate dispense and cure times.

NYLOK Corp.
Macomb, MI 48042 4007
Nov 01, 2004 Permanently fused on bearing surface of fastener, NYSEAL® self-sealing coating compresses slightly and fills void under bearing surface of head and countersink or bore. It covers 2–3 thread pitches down shank and requires no additional curing or heating after installation. NYSEAL prevents galvanic corrosion between dissimilar materials and is suited for sealing applications involving hydraulic fluids, oil, gasoline, petroleum fluids, water, and gaseous vapors.

Cotronics Corp.
Brooklyn, NY 11232
Oct 18, 2004 Applied by caulking cartridge, 7030 sealer forms gas tight seals with no objectionable odors or harmful fibers. Free flowing formulations are available for rapid or automatic dispensing applications. Room temperature-cure product bonds to metals, ceramics, door gaskets, tadpole gaskets, and ceramic cloths with no special surface treatment required. Corrosion and erosion resistant coatings are formed after a quick post cure at 600°F.

Master Bond, Inc.
Hackensack, NJ 07601
Oct 04, 2004 Type EP34AN room temperature cure, 2-component epoxy adhesive/sealant, with thermal conductivity of 22–24 BTU/in/ft²/hr/°F, maintains physical properties after prolonged exposure to temperatures from 400–450°F. It exhibits dimensional stability and electrical insulation properties and can be applied without sagging or dripping. Able to bond to various substrates, 100% reactive epoxy has Shore D hardness of greater than 85 and tensile strength of 5,500 psi.

Henkel Loctite Corporation
Rocky Hill, CT 06067
Aug 27, 2004 Medium-viscosity, UV- and moisture-curing Loctite® 5252 is designed for post-assembly use on electronic module enclosures. Based on polyether rubber technology, thixotropic sealant withstands temperatures from -40 to +125°C and offers controlled flow. It seals seams without seepage or dripping and allows users to tack material within seconds. Sealant-incorporated fluorescent dye enables online inspection for accurate, complete application.

Master Bond, Inc.
Hackensack, NJ 07601
Aug 06, 2004 Dual-component EP42HT-2 epoxy adhesive, sealant, coating, and casting material withstands repeated sterilizations, including radiation, ethylene oxide, chemical sterilants, and steam. Featuring service operating temperature range of -60 to +450°F, product exhibits chemical resistance and Shore D hardness greater than 75. Properties include mixed viscosity of 3,500 cps and tensile strength greater than 12,000 psi. It is castable in thicknesses exceeding 2–3 in.

Master Bond, Inc.
Hackensack, NJ 07601
Jul 15, 2004 One-component, heat-curing, EP17 offers service operating range of -300 to +600°F and cures in 60–90 min at 300–350°F. Product bonds to metals, glass, ceramics, vulcanized rubbers, and plastics. Chemical-resistant EP17 has Shore D hardness greater than 90, compressive strength greater than 13,000 psi, and tensile strength of 8,700 psi. Flowable paste is 100% reactive, does not contain solvents, and can be applied on vertical surfaces without sagging.

Garon Products, Inc.
Wall, NJ 07719 1924
Apr 22, 2004 Joint Guardâ„¢ fills expansion joints with flexible epoxy seal that will not become brittle or break out as sections of floor expand and contract in response to temperature changes. With 100% solids formula, product flexes up to 50% and withstands heavy traffic and chemical contact. Pourable, self-leveling, self-priming, non-shrink sealant prevents contaminants from pooling in joint areas.

Devcon
Danvers, MA 01923
Mar 24, 2004 Effective at temperatures to 250°F (dry) and 125°F (wet), 4 oz Magic Bond(TM) Epoxy Stick consists of 2-part epoxy putty designed to seal leaks and repair gouges in steel, aluminum, wood, fiberglass, concrete, and ceramics. Product mixes by hand kneading, hardening in 30-40 min to finish that can be painted, sanded, machined, tapped, or drilled. Dual-color putty stick includes resin (green) and activator (white), which blend to uniform light gray.

TruSeal Technologies Inc.
Beachwood, OH 44122
Mar 15, 2004 Available in black, EdgeThermâ„¢ PIB-H1 gun grade, 100% solids sealant system is based on polyisobutylene (PIB) polymer formulated to impart reinforcement, resist degradation from UV light and oxidation, and provide low moisture permeability. It resists shearing and retains flexibility through its temperature range to compensate for thermal movement of IG units. Product adheres to glass and metal.

Permabond
Somerset, NJ 08873
Mar 08, 2004 PERMABOND® LH050 PURE Anaerobic Pipe Sealant fills up entire space between male and female metal components and instantly seals connection. Cured product typically exceeds burst rating of pipe and locks pipes, plugs, or fittings against vibration loosening. Single-component paste will seal even when direction in which pipe must face does not allow complete seating of threads. Disassembly of fittings for maintenance is still possible using normal tools.

Permabond
Somerset, NJ 08873
Mar 08, 2004 PERMABOND PURE Anaerobic Adhesive/Sealants are single component liquids that cure when in contact with metal parts and oxygen is excluded. They fill gaps between mated parts by curing to hard plastic and locking assembly in place. PERMABOND PURE Threadlocking Adhesives/Sealants cure to cross linked plastic with environmental and temperature resistance. Examples include medium-strength, medium-viscosity MM115 and very low viscosity ML186 threadlocker and sealant.

Permabond
Somerset, NJ 08873
Mar 08, 2004 Medium-viscosity, anaerobic Permabond HM130 prevents loosening of threaded fasteners and is suited for automated assembly processes. Used for cylindrical parts, Permabond HM162 retaining compound fixtures in 2-5 min. GASKETMAKER® Permabond MH196, non-flammable flange sealant forms instant, low-to-moderate pressure-resistant, leak-free seal and allows for metal-to-metal contact. Thixotropic property prevents migration before and during cure.

Devcon
Danvers, MA 01923
Feb 26, 2004 Flex Bondâ„¢ two-component adhesive bonds flexible piping made of PVC, ABS, and other plastics. Once methacrylate polymer has been applied to 1 of 2 surfaces to be joined, activator can be sprayed on top of polymer or onto other surface. Working time is 3–4 min following activation. Flex Bond requires no mixing, attains functional cure in 1 hr at room temperature, and withstands temperatures to 200°F. It fills gaps up to 25 mils and has tensile elongation of 16%.

Dymax Corp.
Torrington, CT 06790
Feb 19, 2004 Intended for thermoformed plastic clamshell and tube packaging, Light-Weld® 3081 and 3082 Sealants cure upon exposure to UV light in seconds, allowing production line speeds up to 30 fpm. Products create crystal clear bonds and eliminate marking or discoloration that can occur with heat sealing RF or sonic welding. Solvent- and ODC-free, each adhesive comes in standard and thick viscosity grades to suit various dispensing and flow requirements.