Electronics Assembly, Henkel Corporation    Irvine, CA 92606
Apr 01, 2011 Ablestik C100 series conductive die attach films include Ablestik C130 formulation with 30 micron thickness and Ablestik C115 with 15 micron thickness. Suitable for use with die sizes ranging from 1 x 1 mm up to 6 x 6 mm for package types including QFNs and QFPs, films provide optimal wetting ability with lower bonding temperature for stable adhesion strength. This enables adhesion against moisture and MSL Level 2 performance on all leadframe surface finishes.

Laird Technologies    Chesterfield, MO 63017
Mar 29, 2011 With thermal conductivity of 3.5 W/mK, Tputty(TM) 506 series is specifically formulated to fill large and uneven gaps in high-wattage electronic assemblies. Soft, single-part, silicone putty does note require any cure, transfers little to no pressure between interfaces, and is non-abrasive. Conformable and reworkable, filler is colored for automatic detection systems and has viscosity that eliminates bleed and pump-out associated with grease.

DriTac Flooring Products, LLC    Clifton, NJ 07012
Mar 25, 2011 With 4-in-1 formulation, DriTac SMC reduces time and labor associated with sealing concrete substrate or adding sound control membrane in preparation for glue-down hardwood flooring installation. Single-step system reduces moisture vapor transmission in concrete substrates from as high as 12 lb per ASTM 1869 and also allows up to 85% RH per ASTM 2179. Adhesive also forms sound control membrane, acts as crack suppressant, and bridges existing cracks in concrete substrates up to 1/8 in.

Master Bond, Inc.    Hackensack, NJ 07601
Mar 25, 2011 Serviceable over wide range of 4 K to 250°F, Polymer System EP37-3FLF cures at room temperature in 2-3 days or faster at elevated temperatures. Optically clear, 2-component epoxy offers non-critical 1:1 mix ratio and low mixed viscosity of 1,400-1,500 cps. With bond shear strength exceeding 2,000 psi and T-peel strength of 25 pli, flexible epoxy bonds to metals, glass, ceramics, rubber, and many plastics, and may serve as potting, encapsulating, and casting system.

Eastex Products, Inc.    Holbrook, MA 02343
Mar 24, 2011 Suitable for use in finished products, Slip-Not(TM) Anti-Abrasion Grip material features random size dot pattern and soft, supple texture that offers powder-coat finish aesthetic. It performs in wet/dry conditions and can be sewn and sonic- or RF-welded. Available in black and several earthtone colors, PVC-coated fabric exhibits greater than 12,000 Taber Test Revolutions. Washable and waterproof product can be supplied with adhesive on back or laminated to other materials.

H.B. Fuller Co., North America    St. Paul, MN 55110
Mar 15, 2011 Designed to optimize bonding on broad range of challenging substrates such as coated stocks and high recycled-content board, Advantra Encore(TM) provides aggressive hot tack, enabling it to grab and hold quickly to prevent pop-opens with high-memory board. Ability to perform across broad service temperature range of -20 to 140°F eliminates need for multiple adhesive products to handle varying temperatures.

Insite Solutions, LLC    Wake Forest, NC 27587
Mar 09, 2011 Superior Mark Corner is L-shaped industrial floor marking tape with beveled edge on all sides. Pressure sensitive adhesive is recessed to just behind beveled edge, enabling forklift pallets to ride up and over edge rather than dislodge tape. Designed for industrial floors of factories and warehouses, product offers quick installation and maintenance. Tape is available in 6 colors for facilities that implement lean or 5S initiatives.

Henkel Loctite Corporation    Rocky Hill, CT 06067
Mar 08, 2011 Designed for structural assembly of metals, especially aluminum, Loctite® H8100 and H8110 Speedbonder(TM) Adhesives are green-colored, 2-component acrylic formulas that cure at room temperature. Loctite H8100 fixtures in 20 min, while Loctite H8110 fixtures in just 5 min. Both feature glass spacer beads that maximize toughness and prevent adhesive from squeezing out of joint during clamping. Available in 50 and 490 ml dual cartridges, adhesives are stronger that spot welds and rivets.

Master Bond, Inc.    Hackensack, NJ 07601
Mar 03, 2011 Used for coating, lining, bonding, or sealing, EP21AR withstand acidic environments - including immersion in 96-98% sulfuric acid and 36% hydrochloric acid for over one year. This 2-component epoxy, with dielectric strength of 400 V/mil, also acts as electrical insulator and is serviceable from -60 to +275°F. It produces abrasion-resistant bonds with tensile strength over 10,000 psi, shear strength exceeding 2,700 psi, and compressive strength greater than 14,000 psi at 75°F.

Henkel Loctite Corporation    Rocky Hill, CT 06067
Mar 01, 2011 Suited for metal fasteners from ¼-¾ in. in diameter, Loctite® 243(TM) withstands temperatures up to 360°F, cures without primers, and tolerates contamination from thread lubrication, anti-corrosion, and protection fluids. Removable-strength, medium-viscosity, thixotropic liquid will not migrate once applied to fastener's surface. Product fixtures in 5 min and achieves full cure in 24 hr. Registered to NSF Category P1, threadlocker can be used in and around food processing applications.

Creative Materials Inc.    Ayer, MA 01432
Mar 01, 2011 Formulated for use in manufacture of computer components and LEDs, 109-12 Thermally Conductive Low-Stress Epoxy is resistant to thermal-cycling and exhibits minimal shrinkage during cure. Thermal adhesive, used to interface between heat-producing component and heat-sink in electronics designs, has viscosities of 500,000 cps at room temperature or 60,000 at 50°C. This reduces air entrapment, required amount of applied product, and thermal resistance.

DuPont Co., Packaging & Industrial Polymers    Wilmington, DE 19898
Feb 23, 2011 Because ionomer-based DuPont(TM) PV5400 Series is fundamentally resistant to moisture intrusion, it is possible to achieve lasting edge integrity without caulking or additional edge sealing. Compared with traditional EVA and PVB encapsulants, PV5400 Series has up to 100 times more electrical resistivity, offering modules optimized electrical insulation, which minimizes current leakage. Products are available in roll form with sheet thicknesses of 400 and 500 microns.

Glue Dots International, LLC    New Berlin, WI 53151
Feb 23, 2011 Available in ¼ and ½ in. wide permanent adhesive patterns with thicknesses from 3-5 mil, Small MatrX(TM) pressure-sensitive adhesive (PSA) micro-dots apply smoothly and are intended for substrate-to-substrate bonding in commercial and industrial applications. Product, which offers alternative to transfer tape and bonds instantly, provides clean cut-off with no residue or waste. Dots may be used with triggerless, refillable Dot Shot® Pro (DSP) applicator.

Saint Gobain Performance Plastics    Garden Grove, CA 92841
Feb 08, 2011 Reducing noise transfer between rooms, Green Glue Noiseproofing Sealant adheres firmly to wood or metal studs, concrete, plasterboard, and other types of building substrates and will not dry out or crack with age. Water-based and non-toxic product has minimal odor and can seal cracks in floors, walls, and ceilings. Applied along edges and joints, it can be painted once dry and cleans up with soap and water.

Saint Gobain Performance Plastics    Garden Grove, CA 92841
Feb 08, 2011 Installed between floor joist and subflooring, Green Glue Noiseproofing Joist Tape creates airtight seal, stopping friction and eliminating noise by damping loud foot traffic. Tape is rolled onto floor joists, adhesive side down, using taper roller and subflooring is installed on top. Available in 3 standard widths of 1 7/16, 2¼, and 3 in., tape has low thermal conductivity and helps optimize energy efficiency in residential and commercial buildings.

Creative Materials Inc.    Ayer, MA 01432
Feb 03, 2011 Pressure sensitive, double-sided tapes and adhesive-transfer films are available in thicknesses from 0.002-0.010 in. Anisotropically conductive products are resistant to temperature extremes, humidity, and direct exposure to sunlight. Double-sided, pressure sensitive tape No. 300-01 is 0.009 in. thick and conductive on one side. Metal foil support film transmits electricity down length of tape, while acrylic PSA system is heat-resistant to over 100°C.

All Packaging Machinery Corp.    Ronkonkoma, NY 11779
Feb 02, 2011 Incorporating speed control and digital temperature controls, USDA-approved HCBS rotary band sealer offers odorless and smokeless sealing with ¼ in. secure final seal and trim. Dual heating sections and dual cooling sections ensure secure seal, while trim after seal system and vacuum trim accumulation system ensure clean, straight trim directly at seal edge. Heavy-duty, chrome-plated sealing assemblies handle PE, PP, Polyolefin, and PVC shrink films.

Surface Guard, Inc.    Aurora, IL 60504
Jan 26, 2011 Surface Guard® 135 series provides temporary protection of textured or semi-matte finished metals and plastics. Coated with water-based acrylic adhesive system, polyolefin film adheres to surface, exhibits low adhesion build over time, and can be removed when protection is no longer required. Products are supplied on 1.5 mil Linear Low Density or 2.5 mil Low Density PE films; clear and tinted films are also available. Widths from 1-80 in. and roll lengths to 15,000 ft are available.

Master Bond, Inc.    Hackensack, NJ 07601
Jan 20, 2011 Formulated for structural applications in extreme environments with temperatures from -80 to +425°F, Master Bond Supreme 33 bonds to metals, glass, ceramics, wood, vulcanized rubbers, and many plastics. Toughened 2-component adhesive resists thermal cycling, thermal shock, and impact as well as water, oil, and many organic solvents. Designed to cure at room temperature in 48-72 hr, 100% reactive epoxy achieves shear strength over 2,500 psi and tensile shear strength greater than 7,500 psi.

Dymax Corp.    Torrington, CT 06790
Jan 18, 2011 Suited for appliance assembly applications, 3225-T-SC rapidly bonds, laminates, and seals most plastics such as PMMA, PC, PVC, ABS, PA, PU, SAN, TPU, and aluminum. Product is bright blue in uncured state, enabling automated vision systems to confirm adhesive placement prior to cure. During curing process, adhesive transitions to clear, confirming that full cure has been achieved. Product cures tack-free after exposure to broad-spectrum curing equipment in less than 4 sec at 200 mW/cm².