Gluefast Co., Inc.    Neptune, NJ 07753
May 09, 2007 High in solids and offering lay flat qualities, acid-free GF 878U can be used to mount items onto foamcore, chipboard, matboard, and corrugated surfaces, as well as wood. Product is suited for use in roll coaters and is available in quarts, gallons, 5-gal pails, and 55-gal drums.

Epoxies Etc.    Cranston, RI 02921-3407
May 01, 2007 Impact resistant epoxy adhesive Type 10-3216 bonds to metals, woods, plastics, rubbers, and masonry products. Featuring 1:1 mix ratio, it will not crack, and is available in low viscosity translucent version as well as high viscosity gray version. Structural adhesive can be used in cryogenic bonding and is suitable for many aircraft and aerospace applications.

Akron Coating & Adhesives, Inc.    Akron, OH 44301
Apr 27, 2007 Offering peel values up to 32 lb-in., ACA 161A is designed to bond polypropylene and other engineering plastics to metals such as aluminum. It can be applied directly to materials surface, eliminating assembly time required for primers. Adhesive may be applied to metal foil by gravure printing, reverse roll, or wire wound bar coating methods. If necessary, it can also be applied with brush, paint roller, or by spray coating.

ShieldMark, Inc.    Rocky River, OH 44116
Apr 23, 2007 MightyLine(TM) floor tapes draw attention to areas where extra caution is required. While black diagonally lined versions are available in 2, 3, 4, and 6 in. widths, red diagonally lined versions come in 2, 3, and 4 in. widths. Either color is resistant to wear and can be cleaned with industrial scrubbers. Peel-and-stick floor tapes employ aggressive adhesives that leave minimal residue upon removal.

Master Bond, Inc.    Hackensack, NJ 07601
Apr 11, 2007 Providing resistance to water and chemicals, 2-component EP37LV-1 Polymer System features tensile strength in excess of 8,300 psi, working life of 30 min at room temperature, and final mix viscosity of 5,000 cps. Full cures are obtained in 8-10 hr, while complete cures take longer at lower temperatures. Applications range from grouting, troweling and concrete patching in damp locations to marine coatings, floor toppings, and solder substitutes for copper pipe joints.

Compac Corp.    Hackettstown, NJ 07840
Apr 03, 2007 Utilized for foam and gasket fabricating, NetBond(TM)30 acrylic adhesive tape is water-resistant and functions as general-purpose laminating tape. Moisture stable liner and synthetic fiber netting enable tape to adhere to diverse materials and surfaces such as ether, ester, polyethylene, neoprene, and vinyl nitrile foams. Able to adapt and form to curved surfaces, tape is suited for automotive, appliance, and industrial applications.

Aremco Products, Inc.    Valley Cottage, NY 10989
Mar 26, 2007 Consisting of inorganic, ceramic and metal-filled paste, Pyro-Putty® 653 bonds tenaciously to cast iron, steel, and stainless steel. Thixotropic formula can be applied to horizontal and vertical surfaces in cross sections up to ½ in. thick. It is chemically inert and will not decompose at ultra high temperatures. Resistant to most fuels, solvents, and other corrosives, compound is suited for sealing cast steel castings, housings, pipes, and flanges.

Adchem Corp.    Riverhead, NY 11901
Mar 21, 2007 HF series hybrid glazing tape provides high-strength, UV-resistant acrylic adhesive bond to glass and rubber-based adhesive bond to vinyl lineal coated on cross-linked closed cell polyolefin foam. Foam has 338% modulus of elasticity and less than .4% water absorption, creating impermeable moisture barrier. Also offered with blue polyethylene release liner, AAMA-approved tape is available in 1/16th white and black in 72 yd long rolls to 60 in. wide.

3M    St. Paul, MN 55144
Mar 15, 2007 Available in pressurized cylinders, Scotch-Weld(TM) Adhesives come in choice of formulations to meet variety of regulatory requirements, including post-formable, non-flammable, no HAPS, low VOCs, no ozone depleting chemicals, and SCAQMD. Pressurized application ensures optimal use of adhesive contents with little product waste. Offering spray widths from 1-12 in., adjustable-tip spray gun provides multiple spray patterns with choice of drying speed and bonding strength.

Birchwood Casey    Eden Prairie, MN 55344 2138
Mar 13, 2007 Meeting multiple Federal Government Green Purchasing requirements, INTERCEPT® SPS shrink film, stretch film, flat stock, and bags protect products from corrosion and deterioration during shipment and long-term storage. HDPE film, infused with metallic copper particles and activated carbon, proactively neutralizes and removes corrosive elements in air around product while also killing any acid-producing bacteria, mold, or fungus. It has no chemical content and produces no fumes.

Henkel Loctite Corporation    Rocky Hill, CT 06067
Mar 13, 2007 Pre-applied to board at corners of CSP pad site using standard dispensing system, one-component Loctite® Cornerbond(TM) 3508 cures during normal lead-free solder reflow, allowing for self-alignment of IC components. It provides 6-month shelf life, pot life greater than 75 hr, and ability to use standard refrigerated storage. Reworkable feature enables defective components to be removed without requiring entire assembly to be scrapped.

Epoxies Etc.    Cranston, RI 02921-3407
Mar 12, 2007 Electronics-grade UV-curable adhesive and potting compound, UV Cure 60-7108, adheres to most substrates and exhibits favorable exterior durability. It self levels in and around electronic components and is formulated to maintain its clarity over time. Suitable uses include fiber optics or other optical bonding applications.

Pres-On Products, Inc.    Addison, IL 60101
Mar 09, 2007 SG6400 Series Structural Glazing Tape is coated on both sides with acrylic adhesive that bonds instantly with fabrication materials such as vinyl, plastics, powder paints, bare metal, and glass. With rugged construction, high-strength open cell urethane foam tape resists fungi and oxidation to preserve performance and appearance of building structures. It is available in 1/8, ¼, or 3/8 in. thicknesses on rolls up to 50 ft long.

Adchem Corp.    Riverhead, NY 11901
Mar 08, 2007 Featuring pressure sensitive acrylic adhesive, fiber-filled Models 7742-74 and 7745-74 are 2 mils and 5 mils, respectively. Both provide optimal shear strength at elevated temperatures up to 300°F, and offer bond strength sufficient for splicing metal coils. Polyester fiber reinforcement provides roll stability when slit to widths as narrow as in 1/8 in. Tapes resist thermal cycling, salt solution, acid, brake fluid, and UV environments.

Huntsman Advanced Materials    Los Angeles, CA 90039-1011
Mar 08, 2007 Featuring chemical and moisture resistance, ARALDITE® Epoxy Adhesives are suitable for bonding and potting electronic components. Room temperature- and elevated temperature-curing products are RoHS-compliant and sag resistant. Providing lap shear strength, high-temperature ARALDITE® Polyurethane Adhesives can bond hard-to-join thermoplastic substrates and encapsulate pressure-sensitive components. All come in dual-barrel cartridges as well as bulk packaging for automated mixing/dispensing.

Master Bond, Inc.    Hackensack, NJ 07601
Mar 02, 2007 With service temperature range of -60°F to over 400°F, Type EP30HT epoxy produces high strength, rigid, chemical resistant bonds, and adheres to similar and dissimilar materials such as metals, glass, ceramics, wood, vulcanized rubbers, and plastics. Product attains shear bond strengths over 3,200 psi, with volume resistivity greater than 1,015 W-cm, dielectric strength of 440 V/mil, and dielectric constant of 3.46 at 1 MHz.

APM-Hexseal Corp.    Englewood, NJ 07631
Mar 01, 2007 Used with company's re-usable, high-pressure, self-sealing screws, bolts, and nuts, mechanical and liquid-applied threadlockers are fully adjustable Nylon locking pellets and strips that can be added to thread surface and precisely positioned to optimize anti-vibration dampening. Devices remain locked, whether fastener is seated or unseated, and are impervious to chemicals/water/motor fluids. Reusable to +550ºF, products do not dry, shrink, or loose resiliency upon chemical exposure.

National Starch & Chemical Co.    Bridgewater, NJ 08807-0500
Feb 28, 2007 Balancing tack, open time, and set speed while minimizing moisture transfer into sheet, Ultimate Control(TM) 32-541A resin adhesive helps laminators attain optimal line speeds. Hold-out properties let operators meter glue-line width, reducing waste adhesive drip from flute tips. Glue line thickness can be metered down, and adhesion and set time can be controlled. Product runs effectively on heavy, coated, or varnished sheets as well as on lighter, uncoated sheets without slinging.

National Starch & Chemical Co.    Bridgewater, NJ 08807-0500
Feb 28, 2007 Used for making rolled goods for metal buildings industry, Bondmaster® 40-453A is formulated copolymer emulsion adhesive that bonds foil, scrim, kraft, and other facings to fiberglass insulation. Able to be roll coated, extruded, or air sprayed, this 54% solids adhesive has 800 cps viscosity and formulation that promotes wet tack and product life expectancy. Tack reduces slippage of poly or foil facings when bonded to fiberglass.

National Starch & Chemical Co.    Bridgewater, NJ 08807-0500
Feb 28, 2007 DURO-TAK(R) acrylic solution pressure sensitive adhesive is designed to enable dispersed drug patch formulations. Supplied in non-polar cyclohexane solvent, it is targeted at specific drugs that have low solubility in non-polar solvents, and simplifies preparation of dispersed drug-in-adhesive patches by reducing potential for supersaturation.