Adhesives & Sealants

Adhesives & Sealants

Epoxy Adhesives/Sealants are silicone-free.

Jan 02, 2002

EMCAST FIPG 1850 is curable by UV light in 325-380 nm range. Viscosity is rated at 60,000 cps, and its hardness A rating is 65. EMCAST FIPG 1851 is curable by UV light in 325-380 mn range. Viscosity is rated at 60,000 cps, and its hardness A rating is 80. Emcast FIPG 1852 acrylate based prepolymer is curable by UV light in the 325-380nm range or by heat. Viscosity ranges from 50,000-60,000 cps,... Read More

Adhesives & Sealants

Water-Based Adhesives suit automotive assembly applications.

Jan 02, 2002

Environmentally friendly water-based adhesives work on porous substrates such as foams, cloth, felt, and insulation, and non-porous materials such as wood, plastic and metals. Products are available with fast-tack and foam tearing strength comparable to solvent based adhesives. Adhesives are fast setting for use in general upholstery, foam-to-foam, foam-to-fabric, or foam-to-wood bonding, and may... Read More

Adhesives & Sealants, Materials & Material Processing

Encapsulant/Potting Material exhibits <1% shrinkage.

Dec 27, 2001

Ceramacast(TM) 510 aluminum oxide based, hydraulic-setting ceramic compound potting material can be used to encapsulate cartridge heaters and embed high temperature components to 3200ºF. Supplied as dry powder, Ceramacast 510 is bonded using calcium aluminate and as-cast. Its dried density is 180 lbs/ft3, and it exhibits exceptional thermal conductivity and dielectric strength of 75-100... Read More

Adhesives & Sealants

Epoxy Adhesive fixes electrical coils.

Dec 20, 2001

Tra-Bond CA20 thixotropic epoxy adhesive system is formulated for shorted turns, damaged end wire extensions, or other coil repair applications where high-fill, non-sag adhesive is needed. It provides high dielectric isolation and good mechanical strength. Readily mixed, handled, used, and cured at room temperature, Tra-Bond CA20 develops strong bonds to materials such as metals, glass, ceramics,... Read More

Adhesives & Sealants

Gasket Tape protects fragile equipment.

Dec 18, 2001

Made from 100% multidirectionally expanded PTFE, GORE-TEX Series 600 gasket tape seals large-diameter fragile and glass-lined equipment. It is resistant to all chemicals, tolerates temperatures from -450 to +600°F, and is available in 5 widths and thicknesses of 1/4 and 3/8 in. Tape maintains original width when compressed, ensuring high gasket stress retention, dimensional stability, and... Read More

Adhesives & Sealants

Adhesive Transfer Films perform well on foam substrates.

Dec 17, 2001

4-mil Unifilm U618A and 5-mil Unifilm U619A high-performance acrylic adhesive transfer films offer extremely high tack, and are designed to provide high initial wet out and superior anchorage to ether and ester foams. Transfer films perform well over range of operating temperatures, and offer very high peel strength. Products deliver humidity and water resistance, and may be die-cut. Read More

Adhesives & Sealants

Adhesive Epoxies come in pre-formulated cartridges.

Dec 17, 2001

Epox-Eez(TM) twin pack cartridges are pre-filled, measured and mixed. Adhesive will cure at room temperature, provide 500°F service, and have chemical, electrical and moisture resistance. Epox-Eez cartridges are available for company's General Purpose 4525N, Low Viscosity 4461N, Vibration Resistant 4535N, Fast Set 4537N, Ultra Flexible 4538N, and Machinable Epoxy 4540N high-temperature... Read More

Adhesives & Sealants

Epoxy Board is designed for use at temperatures to 250°F.

Dec 13, 2001

Ren Shape 5008 epoxy board can be machined with carbide cutters to generate molds with good edge definition, dimensional stability, and smooth surface finish. It can be used to produce intermediate-temperature models, heat-resistant thermoform tooling, and lay-up tools for composite parts. Molds may be produced for thermoforming detailed, production-quality parts from polypropylene, polystyrene,... Read More

Adhesives & Sealants

Adhesive Tapes minimize media fogging and head corrosion.

Dec 11, 2001

ARclean(TM) 9006 and ARclean(TM) 9019 are low-outgassing products for use in fabrication of tape seals and labels in hard disk drive assemblies. ARclean(TM) 9006 cleanly strippable adhesive features 3 mil matte chrome polyester backing. ARclean(TM) 9019 electronically clean adhesive features 2 mil thermally printable, white polyester film label stock. Both adhesives have ultra low total VOCs and... Read More

Adhesives & Sealants, Services

Ceramic Adhesive is formulated with phosphate binder.

Dec 11, 2001

Ceramabond(TM) 690 single part, boron nitride filled ceramic adhesive bonds and coats in temperatures to 2700°F, and can be used in oxidizing atmospheres to 1560°F and reducing and vacuum environments to 2700°F. Thermal conductivity is 55 W/m-°K, and dielectric strength is rated at 500 volts/mil. Exceptional resistance is shown to molten glasses and metals. Curing time is 1-2 hours... Read More

Adhesives & Sealants

Epoxy Resin bonds to most materials.

Dec 11, 2001

TRA-BOND 2111 thixotropic epoxy resin and hardener formulation is developed for industrial adhesive, staking, laminating, repair, and manufacturing applications where long pot-life, good wetting, non-sag, and non-drip properties are required. Two-part system contains no volatile solvents, and cures at room temperature. It bonds to glass and glass fabrics, ceramics, wood, leather, most metals, and... Read More

Adhesives & Sealants

Lamination Adhesives improve holdout when aerated.

Dec 11, 2001

Aerobond 32-192A and 12-200A adhesives are able to contact substrate surface without flowing down and away from where bonding should occur. Type 32-192A is for Automatan and similar laminating equipment; 12-200A formulated dextrin adhesive is for general purpose laminating. Both should be applied with nip rollers. Read More

Adhesives & Sealants

Epoxy Casting Compound meets UL fire retardant specs.

Dec 11, 2001

TRA-CAST 3143 has low viscosity, long pot life, and is certified to UL 94 V-O. Epoxy system has low coefficient of thermal expansion and excellent wetting and adhesion to most electronic and aerospace-industry materials, including metals, glass products, ceramics, industrial laminates and many rigid plastics. Applications include rigid potting, laminating, transformer encapsulating, filament... Read More

Adhesives & Sealants

Epoxy emits no VOCs.

Dec 11, 2001

Two component EMCAST 758 thermally conductive epoxy has moderate viscosity of 130,000 cp, glass transition temperature of 125°C, thermal conductivity of 3 W/mK, and is not electrically conductive. It is 100% solids epoxy with no solvent for zero VOCs. Epoxy is available in pre-mixed and frozen syringes or in two component kits with mix ratio of 2:1. Substrates include aluminum, stainless... Read More

Adhesives & Sealants

Thermally Conductive Epoxy cures at room temperature.

Dec 10, 2001

Two component EMCAST has viscosity of 130,000 cps, specific gravity of 1.90, and glass transition temperature of 125ºC. Its thermal conductivity is 3 W/mK, and it is not electrically conductive. 100% solids epoxy has no solvent for zero VOCs. Epoxy cures in 8 hours @ 25°C, 1 hour @ 65°C, and 15 minutes @ 100°C. It is available as pre-mixed and frozen syringes or in two component kits.... Read More

Adhesives & Sealants

Machinery Adhesives lock and seal nuts and bolts.

Nov 28, 2001

Superlock adhesives provide positive locking and sealing on both active and inactive surfaces. Screw Lock Grade 2222 low-strength threadlocker is for spiral screws less than 1/4 in. diameter. Medium-strength Grade 2242 works on nuts, bolts, and screws with diameters up to 3/4 in. Grade 2262 high-strength formula controls torque/tension and clamp load on larger bolts and nuts in applications... Read More

Adhesives & Sealants

Epoxy Adhesive has low vapor pressure.

Nov 28, 2001

Two-part Tra-Bond 2116 thixotropic adhesive can be used in electronic and industrial applications where high-fill, non-sag adhesive is needed. It bonds well to many substrates including metals, glass, ceramics, wood, and plastics. Adhesive cures at room temperature, is electrical insulator, and is NASA outgassing approved. It resists chemicals and weather. Read More

Adhesives & Sealants

Graphite Adhesive works at temperatures to 5400° F.

Nov 28, 2001

Resbond 931 cures at 250°F to form 99% pure graphite bonds that have bond strengths in excess of 2500 psi. Bonds are electrically conductive and resist reducing atmospheres, most chemicals, and solvents. Applications include repairing cracked or broken graphite trays, fixtures, and dies; filling and rebuilding crevices, cracks, and worn areas; and bonding graphite cloths, felts, and boards. It... Read More

Adhesives & Sealants

UV Adhesive bonds fiber optics.

Nov 21, 2001

TRA-BOND F 175 clear, low viscosity adhesive bonds metals, ceramics, and most rigid polymers. Cure time of a few seconds upon exposure to ultraviolet light makes it suitable for fiber optic terminations where fast cure is required. It produces very little shrinkage upon cure, so stress is minimal. Adhesive also works well in high humidity environments or in applications that require thermal... Read More

Adhesives & Sealants

Moisture Resistant Encapsulant has smooth consistency.

Nov 21, 2001

Tra-Bond 933-1.5 electrically insulating epoxy encapsulant is formulated to provide smooth crowns over devices of wire bonds. Encapsulant provides protection from thermal and mechanical shock. Compound is stable at room temperature for up to three months, but is best kept stored at -40°C or colder, since filler may settle. Read More