Adhesives & Sealants

Related Categories
Adhesives & Sealants, Construction Equipment & Supplies

Window and Door/Fireblocking Foam Sealant has all-in-one formula.

May 19, 2015

While formulated to serve as low-pressure, expanding Window & Door/Insulating foam that is AAMA 812-10 compliant and will not bow window or door frames, Thermal Seal All-In-One Foam Sealant may also be used as UL-evaluated fireblocking foam for use in Type V non-rated 1 & 2 family residential construction. Closed cell content increases R-value as well as overall strength and resistance to leakage of air and water vapor. Read More

Adhesives & Sealants

Conductive Adhesive features low-temperature cure.

May 7, 2015

Designed for die attach and general circuit assembly applications, CA-180 cures in 30 min at 80°C, 3 min at 100°C or 10 sec at 150°C with electrical conductivity of 4 x 10-5 ohm-cm. This low-temperature cure conductive adhesive has 48 hr work life and 12,000 cP viscosity at 5 rpm for facilitated needle dispensing or application by pin transfer. Applications include those where components are temperature-sensitive and require high conductivity interconnects.

Read More

Adhesives & Sealants

Extreme Grip Adhesive eliminates need for nails and screws.

May 6, 2015

Suitable for vertical applications, SikaBond® Ultimate Grab bonds to variety of construction substrates, including bricks, glass, metal, concrete, wood, and ceramics. One-component, moisture-cure, instant grab, polyurethane adhesive was developed with Sika's elastic technology, allowing maximum bond flexibility and recovery for long term durable bond. Product is packaged in 10.1 oz cartridges. Read More

Paints & Coatings, Adhesives & Sealants

Epoxy Coating suits applications above or below water.

May 4, 2015

Based on blend of liquid epoxy polymer and aliphatic polyamine curing agents, KALCOAT™ 560 can displace water from wet surfaces to make permanent bond. High build 100% solids epoxy coating is solvent-free and incorporates Kevlar® microfibers for reinforcement and viscosity management for high application rates. KALCOAT 560 can be used as anti-corrosive coating, repair compound, fairing compound, and encapsulating coating for variety of applications. Read More

Adhesives & Sealants

UV Cure Adhesive suits circuit assembly applications.

April 27, 2015

Designed to cure rapidly when exposed to high-intensity UV light, 535-11M-7 Epoxy is suitable for lens bonding in camera modules, chip encapsulation in smart cards, and variety of general bonding applications in photonics assembly. Flexible, high-strength epoxy adhesive is non-conductive, low-outgassing, and does not contain antimony. Read More

Mounting & Attaching Products, Materials & Material Processing, Adhesives & Sealants

High-Temperature Sealant suits applications to 950°F.

April 24, 2015

Formulated by combining high-temperature resin with ceramic fibers and powders, Pyro-Putty™ 950 can be used as gasketing compound for boilers, compressors, heat exchangers, furnaces, ovens, and exhaust manifolds. Product repairs rough, scored, or irregular surfaces and is resistant to chemical and steam attack, high pressure/vacuum atmospheres, mechanical vibration, and joint movement. Offered in 11 oz caulk gun cartridge, sealant can cure in service or by heating joint without pressure. Read More

Adhesives & Sealants, Paints & Coatings

Two-Part Epoxy Paste has ultra low thermal resistance.

April 7, 2015

Master Bond EP48TC has thermal resistance of 5–7 x 10–6 K•m2/W, which enables thermal conductivity of 20–25 BTU•in/ft2•hr•°F. Applied in bond lines as thin as 10–15 microns, epoxy paste has tensile lap shear strength from 900–1,100 psi and bonds to metals, composites, glass, ceramic, and plastics. Working life for 100 gram batch at 75°F is 90–120 min. Curing at room temperature, it is serviceable over -100 to +300°F and available in ½ pint to 5 gallon containers. Read More

Adhesives & Sealants

Needle-Bonding Adhesive facilitates cure confirmation, inspection.

March 27, 2015

With viscosity of 150 cP, 1405-M-UR-SC is formulated with Encompass™ technology that incorporates See-Cure color change and Ultra-Red™ fluorescing technologies with LED-curing capabilities. Medical device adhesive is blue in uncured state to aid placement verification and fluoresces bright red under 365 nm black light after cure. Suitable for bonding stainless steel, PC, PMMA, and ABS, adhesive facilitates and accelerates cures at 385 and 405 nm wavelengths. Read More

Materials & Material Processing, Adhesives & Sealants

Epoxy Potting Compound resists high temperatures.

March 27, 2015

With 130°C relative temperature index rating, 50-3150RFR Black Epoxy with Catalyst 30 will survive elevated temperatures for long periods of time, which offers benefits as electronics get smaller and hotter. Compound is UL 746B listed and formulated to meet stringent non-burning requirements of UL 94 V-0. Typical applications include encapsulating power supplies, transformers, coils, insulators, and sensors. Read More

Adhesives & Sealants

Epoxy Stick facilitates fuel tank repairs.

March 25, 2015

Offering resistance to ethanol and most solvents, Permatex Fuel Tank Repair Epoxy Stick is suited for filling holes and damaged seams in both metal gas tanks and containers. Product comes as 2-part putty in stick form which helps measure and mix proper amount. Finished repair sets in just 1 hour and can be drilled, sanded, threaded, or filed after 5 hours. When fully cured, epoxy withstands moderate temperatures and does not shrink after application. Read More

Adhesives & Sealants

Conductive Adhesive electrically connects solar cells.

March 6, 2015

Stress absorbing to withstand rigors of thermal cycling, DB-1541-S9 is suited for stringing or shingling applications in crystalline silicon and thin-film solar modules. Adhesive electrically connects solar cells using ribbons or direct cell to cell contact. Providing optimized conductive stability to cell and ribbon metallization during damp heat exposure, adhesive is designed to gel rapidly and then complete cure through encapsulant lamination and cure process. Read More

Materials & Material Processing, Printing & Duplicating Equipment, Adhesives & Sealants

Electrically Conductive Inks suit wearable electronics.

March 2, 2015

Adhering to variety of natural and synthetic fibers, 125-19FS consists of flexible, screen-printable, silicone-based conductive ink that offers low-temperature performance to -70°C, and high temperature properties up to 325°C. Screen-printable 120-07 Ink is extremely conductive with optimal creasing resistance and washability features. Adhering to fabric substrates, 124-33 screen-printable conductive adhesive offers flexibility and resistance to creasing. Read More

Adhesives & Sealants

Thermoplastic Adhesive suits temporary mounting applications.

February 17, 2015

Adhering to ceramics, glasses, and metals, Crystalbond™ 509 is suitable for temporarily mounting substrates that require dicing, grinding, or polishing operations. Thermoplastic adhesive is applied by preheating mounting plate to 250°F, melting and spreading adhesive in uniform layer, then positioning part over adhesive, allowing entire assembly to cool. After processing, Crystalbond™ is dissolved in acetone or Aremco’s 509-S cleaning agent that leaves no film or residue. Read More

Adhesives & Sealants, Chemical Processing & Waste Management, Health, Medical and Dental Supplies & Equipment

Soft Silicone Adhesives suit skin applications.

February 11, 2015

Designed specifically for wound care, Silbione® HC2 2022 medium-viscosity silicone gel is compatible with most coating processes and applicable on wide range of substrates, including PU films, perforated films, and open knit fabrics. Product is manufactured in ISO 8 clean room in ISO 13485 facility to ensure microbial safety on breached skin. For wearable devices, scar management, and transdermal drug delivery, Silbione® RT Gel 4642 high tack silicone gel is available. Read More

Adhesives & Sealants, Chemical Processing & Waste Management, Green & Clean

Acrylic Resins suit ultra-low VOC coatings.

February 10, 2015

Suited for 2-component concrete coatings, MAINCOTE™ AEH Acrylic Epoxy Hybrid combines weatherability and UV resistance of acrylics with chemical resistance of epoxies. Product offers tire pickup resistance in waterborne 2K concrete coatings as well as resistance to aggressive cleaning regimens. With VOC levels of 50 g/L or less, MAINCOTE™ 4950 Acrylic Resin is suited for direct-to-metal coatings. Product offers balance of hardness, corrosion, and durability, as well as architectural gloss. Read More

Adhesives & Sealants

Fast Cure Adhesives suit cartridge dispensing.

February 4, 2015

Suitable for use with TriggerBond® dispensing guns, TriggerBond Epoxies offer shear strength up to 1,500 psi and notched Izod impact of 2.7 ft-lb/in. Adhesive's 2 components are packaged into cartridges, which fit in dual-barrel dispensing gun. Because cartridges contain precise quantities of hardener and resin, TriggerBond produces correct mix ratio every time user squeezes trigger. Three types are available with setting times of 5, 20, and 46 minutes, respectively. Read More

Adhesives & Sealants

UV-Cured Epoxy Adhesive increases electronic assembly reliability.

January 28, 2015

Developed to pass reliability requirements in disk drive, camera module, photonics, and circuit assembly applications, 535-11M-3 eliminates crowning (warpage) of sliders in Head Gimbal Assemblies. This non-conductive, low-outgassing, flexible adhesive does not contain antimony and can be used in other bonding applications in Head Stack Assembly as well as for lens bonding in camera modules, chip encapsulation in smart cards, and general bonding applications in photonics assembly. Read More

Adhesives & Sealants

Die-Attach Adhesives offer optimized rheology.

January 26, 2015

Intended for microelectronics and semiconductor industries, Electraset™ electrically conductive die attach adhesives conform to Test Method 5011 in MIL-STD-883. Electraset™ 620 couples low cure shrinkage with low coefficient of thermal expansion, minimizing chip or device warping and preventing cracking or delamination. Electraset™ 620-2 has virtually no bleed and minimal spreading, tailing, or stringing. Electraset™ 620-3 is used for dispensing, stenciling, and doctor blade application. Read More

Machinery & Machining Tools, Safety & Security Equipment, Adhesives & Sealants

Adhesive Gripping Material helps prevents towel contamination.

January 26, 2015

Featuring water-resistant ShurStep® Non-Skid Abrasive Tape, Get A Grip stops drying towels from falling to floor. This household product, comprised of die-cut, non-slip, peel-and-stick solution, applies in seconds to bathroom towel bars, kitchen appliances, and other racks/handles in various areas throughout home. Rubber-based adhesive coating adheres to any smooth, clean, and dry surface and features finely ground abrasive particulates (80 grit). Read More

Transportation Industry Products, Adhesives & Sealants

Acrylic Foam Tape is designed for automotive applications.

January 23, 2015

With foam core that provides stress relaxation when high application loads are encountered, PX5000 primerless tape can attach automotive exterior trim parts to various materials and substrates. Adhesive on both sides of tape offers process flexibility in die-cutting operations. Product adheres to Low Surface Energy (LSE) and Medium Surface Energy (MSE) plastics as well as medium-to-difficult automotive clear coat systems without need for adhesion promoter or other surface pre-treatment methods. Read More