Master Bond, Inc.    Hackensack, NJ 07601
Jul 03, 2002 Two-component EP75-1 has 100 to 15 mix ratio by weight. It cures at room temperature or more rapidly at elevated temperatures. Adhesive develops bonding strength of more than 2,000 psi tensile shear when measured and cured at 75°F. Volume resistivity of cured system is 50-100 ohm cm. Adhesive contains no solvents or diluents. It is suitable for metals, glass, ceramics, vulcanized rubber, and most plastics. Service operating temperature is -60 to +250°F.

Henkel Loctite Corporation    Rocky Hill, CT 06067
Jul 03, 2002 Fixmaster® Super Grout pourable, aggregate-filled epoxy withstands high torque loading and contains 100 percent solids. Non-shrinking and chemical/corrosion-resistant, it suits self-leveling applications under rails and sole plates. Once mixed, epoxy compound is red in color. Each 5-gallon kit covers 620 cubic inches. Typical applications include diesel or gas engines, generators, cone crushers, mine hoists, and gantry cranes.

Scapa North America    Windsor, CT 06095
Jun 25, 2002 Medifix® 4005/868 single-coated, medical-grade, pressure-sensitive, polyurethane foam tape consists of soft, 0.4 mm, tan, polyurethane foam coated with medical grade acrylic adhesive system. Product is supplied with 80 gsm white glassine release liner. Moisture vapor permeable, Medifix 4005/868 is suitable for wound care, consumer dressings, and general medical fixation.

Epoxies Etc.    Cranston, RI 02921-3407
Jun 24, 2002 Type 20-3650 electronic grade epoxy potting, casting, and encapsulating system exhibits excellent physical, thermal, and electrical insulation properties. Tensile strength is 11,000 psi and compressive strength is 15,500 psi. Compound is DOT non-hazardous, easy to mix, and will cure at room temperature or with mild heat. Operating temperature range is -60 to +150°C. Type 20-3650 is suitable for meter mix and dispense equipment.

Master Bond, Inc.    Hackensack, NJ 07601
Jun 21, 2002 One-component Supreme 3HT-80 has high shear and high peel strength, and resists impact, thermal shock, vibration, and stress fatigue cracking. It adheres to metals, glass, ceramics, wood, vulcanized rubbers, and most plastics. Bonds resist water, oil, fuels and most organic solvents, even upon prolonged exposures. Operating temperature range is -100 to +350°F. It is 100% reactive and does not contain any solvents. Hardened adhesive is thermal insulator.

Permabond    Somerset, NJ 08873
Jun 21, 2002 Permabond® E04 2-part epoxy, with 1:1 mix ratio, has work life of 45 minutes and instant cure through preheat oven in most trickle varnish systems. It protects wire from breakages and wear around comutators in high-impact, high-temperature, high-speed, and high-vibration rotor applications. Epoxy is suitable for Class H motors 180°C (365°F). It is available in 50, 200, and 400 ml cartridges, plus 5 and 19 liter pails.

Avery Dennison, Fasson Roll North America    Painesville, OH 44077
Jun 21, 2002 Fasson® S8010 and S8015 clear acrylic adhesives have good initial tack, high shear, and adhere to any substrate used in electronics devices. S8015 adheres to difficult surfaces, like powder coat paint. Adhesives are available on range of film facestock materials, with or without topcoats, and work with various print treatments, such as flexographic and letterpress printing, and thermal transfer. Both resist chemicals and UV and are recognized by UL.

Epoxies Etc.    Cranston, RI 02921-3407
Jun 20, 2002 Electronic grade, casting, potting, and encapsulating epoxy resin system No. 20-3651\40 adheres to metals, ceramics, and plastics. Physical properties include mixed viscosity of 32,500 cps at 25°C, specific gravity from 1.40 to 1.45 at 25°C, and Shore D Hardness rating of 85 to 88. Tensile Strength ranges from 6,100 to 9,200 psi, and operating temp ranges from -40 to +30 and -65 to +105°C.

Tra-Con, Inc.    Bedford, MA 01730
Jun 19, 2002 TRA-BOND 293-1 high hardness, high Tg epoxy has work life of 8 hr at room temperature, high dielectric constant, and ability to make resilient bonds to variety of substrates like gold, brass and silver. Applications include optoelectronic and instrument assembly.

General Polymers    Cincinnati, OH 45242
Jun 17, 2002 Water-based FasTopâ„¢ seamless urethane cements can be installed and ready for service in hours because of their Urethane-cement chemical reaction. FasTop M, applied as mortar, can be installed in one step without topcoat. FasTop S System consists of trowled slurry blend with silica sand broadcast finish. FasTop S-U1 Upgrade System uses decorative quartz broadcast instead of silica sand and requires clear topcoat.

Tra-Con, Inc.    Bedford, MA 01730
Jun 14, 2002 TRA-BOND 724-20 pre-mixed and frozen adhesive provides strong, resilient bonds to variety of substrates including aluminum, solder, nylon, mylar, and steel. Adhesive strength is maintained in cryogenic conditions, and it provides bond line control for critical alignment applications. Polyurethane exhibits good dielectric properties. Several cure options are available, including room temperature.

Benjamin Moore & Co.    Montvale, NJ 07645
Jun 12, 2002 Moorcraft® Super Spec® alkyd-based primer, sealer, and stain suppressor is suitable for interior use on bare or previously painted wood, plaster, drywall, plywood, and hardboard surfaces. It may also be used on exterior surfaces for limited applications, such as sealing knots or suppressing sap stains. Primer is available in gallons, in white only. Product seals charred or smoke-stained substrates and holds back water soluble stains.

Newman, M.M., Corp.    Marblehead, MA 01945
Jun 06, 2002 Heli-Tube® Spirally Cut Plastic Wrap applies like tape over stair railings, vertical posts, hoses, and electrical wiring. It is unaffected by fresh and salt water, and can be used for abrasion protection. Featuring safety orange, bright yellow, and glow-in-the-dark colors, in-plant applications include marking exit posts and stairway railings with signage that workers can see and feel. Wrap is offered in 1/16 to 1 1/2 in. OD sizes.

Master Bond, Inc.    Hackensack, NJ 07601
Jun 05, 2002 Single component, flexible, UV curable adhesive UV14-3 cures at room temperature in seconds to 1 min. It is not oxygen inhibited and does not require inert atmosphere. It requires no mixing, and develops high bond strengths with metals, ceramics, glass, paper, plastics, and elastomers. UV14-3 has operating temperature range of -60 to +250°F. Product exhibits storage stability of 6 months in original unopened containers.

Tra-Con, Inc.    Bedford, MA 01730
Jun 05, 2002 Clear TRA-COAT WCC2B UV curable one-part adhesive can be used for optical fiber, glass, and general purpose applications. Adhesive is clear, medium viscosity, and cures with exposure to UV light at 100 fpm under 300 W/in. bulb. Easy to apply, it creates strong bonds to clear plastics and glass.

Tra-Con, Inc.    Bedford, MA 01730
Jun 05, 2002 TRA-BOND 2106T 2-part epoxy mixes at room temperature and creates strong bonds to metals, plastics, glass, forestry products, ceramics, rubber, masonry materials, and construction materials. It has low shrinkage, and when fully cured it acts as electrical insulator with resistance to gases, vapors, water, galvanic action, and many organic and inorganic compounds. TRA-BOND 2106T cures quickly at room temperature.

Tra-Con, Inc.    Bedford, MA 01730
Jun 04, 2002 LX10075 adhesive is designed for optical applications as well as general purpose bonding. Low viscosity material is easy to apply. UV cure allows for quick and effective processing.

Tra-Con, Inc.    Bedford, MA 01730
Jun 03, 2002 LX10072 UV/moisture conformal coating is designed for use in high-speed dip, spray, and flow conformal coating equipment. Flexible adhesive, formulated to provide protection against moisture and harsh chemicals, remains bubble free. Product is compatible with industry standard solder masks, no-clean fluxes, metallization components, and substrate materials.

Krylon Diversified Brands    Cleveland, OH 44115
May 31, 2002 Polyurethane Concrete Repair is paintable sealant for joints up to 1 in. wide. It is appropriate for indoor or outdoor applications. Concrete and Mortar Repair is silicone sealant that is suitable for joints and cracks and prevents ice and water damage. Concrete Driveway Repair is latex caulk with resistance to wear. It remains flexible to prevent damage by ice and water. Mortar Patch watertight caulk is paintable, offers flexibility, and cleans up with water.

Master Bond, Inc.    Hackensack, NJ 07601
May 29, 2002 Two-component EP41S-2 epoxy adhesive/sealant and coating cures at ambient temperatures or more quickly at elevated temperatures. It is 100% reactive and contains no solvents or diluents. EP41S-2 adheres to metals, glass, ceramics, wood, vulcanized rubbers, and plastics. It withstands prolonged immersion in strong organic solvents. Operating temperature range is -60 to +275°F.