Permabond    Somerset, NJ 08873
Mar 08, 2004 Permabond® 101 low-viscosity, ethyl cyanoacrylate adhesive has consistent cure speed and bond strength. Suited for use on plastics, rubbers, and metals, product has appropriate stabilization, which maximizes performance throughout shelf-life. It can be used to bond closely fitting parts and is suited for wicking or penetrating applications. Other applications include rubber bonding, jewelry assembly, speaker bonding, and fabric bonding.

Permabond    Somerset, NJ 08873
Mar 08, 2004 PERMABOND PURE Anaerobic Adhesive/Sealants are single component liquids that cure when in contact with metal parts and oxygen is excluded. They fill gaps between mated parts by curing to hard plastic and locking assembly in place. PERMABOND PURE Threadlocking Adhesives/Sealants cure to cross linked plastic with environmental and temperature resistance. Examples include medium-strength, medium-viscosity MM115 and very low viscosity ML186 threadlocker and sealant.

Permabond    Somerset, NJ 08873
Mar 08, 2004 Medium-viscosity, anaerobic Permabond HM130 prevents loosening of threaded fasteners and is suited for automated assembly processes. Used for cylindrical parts, Permabond HM162 retaining compound fixtures in 2-5 min. GASKETMAKER® Permabond MH196, non-flammable flange sealant forms instant, low-to-moderate pressure-resistant, leak-free seal and allows for metal-to-metal contact. Thixotropic property prevents migration before and during cure.

Permabond    Somerset, NJ 08873
Mar 08, 2004 Permabond 801 cyanoacrylate, single-component, quick setting adhesive bonds rubber, metal, and plastics in applications with temperatures up to 150°C. Clear, low-viscosity liquid fixtures in less than 10 sec on most substrates.

Tailored Label Products, Inc.    Menomonee Falls, WI 53051
Mar 04, 2004 Model 3M(TM) VHB(TM) Tape can join dissimilar materials like plastic and metal, glass and metal, and aluminum and steel. It disperses pressure along entire length of seam, unlike rivet or joint where stress is concentrated in certain points. When bonding 2 unlike materials, it can resist differing co-efficients of thermal expansion. Tape prevents galvanic corrosion between metals and provides moisture seal as well as smooth, clean surface.

Scapa North America    Windsor, CT 06095
Mar 03, 2004 Scapa 653 paper tape is single-coated with modified silicone pressure-sensitive adhesive. During hot air leveling and wave soldering operations, it provides protection against chemical solvents, solder, and rinse water while adhering to electronic substrates. Tape leaves no adhesive residue upon removal and is suited for low static protection of gold finger or rhodium PBC contacts, assembly holes, and components during hot air leveling processes.

Birchwood Laboratories, Inc.    Eden Prairie, MN 55344
Mar 02, 2004 DRI TOUCH® PLUS IRP3 penetrant and sealant works on impregnated and non-impregnated powdered metal parts, regardless of density or porosity of surface. Low viscosity liquid penetrates remaining porosity of powdered or sintered metals to displace moisture beneath surface. Once dry, it leaves semi-solid protective film that is absorbed by part itself. Protection levels range from 80–120 hr of salt spray or several hundred hr of humidity resistance.

Henkel Loctite Corporation    Rocky Hill, CT 06067
Mar 02, 2004 Loctite® 4500(TM) and 4501(TM) surface insensitive cyanoacrylate adhesives bond metal, plastic, and elastomeric materials with acidic, porous, and absorbent surfaces. Single-component gel cyanoacrylate Loctite 4500 has consistency that prevents adhesive flow on vertical applications. Wicking viscosity, single component cyanoacrylate Loctite 4501 maintains cure speed for extended time period. Both maintain liquid performance properties over entire shelf life.

Devcon    Danvers, MA 01923
Feb 26, 2004 Flex Bondâ„¢ two-component adhesive bonds flexible piping made of PVC, ABS, and other plastics. Once methacrylate polymer has been applied to 1 of 2 surfaces to be joined, activator can be sprayed on top of polymer or onto other surface. Working time is 3–4 min following activation. Flex Bond requires no mixing, attains functional cure in 1 hr at room temperature, and withstands temperatures to 200°F. It fills gaps up to 25 mils and has tensile elongation of 16%.

Dymax Corp.    Torrington, CT 06790
Feb 19, 2004 Intended for thermoformed plastic clamshell and tube packaging, Light-Weld® 3081 and 3082 Sealants cure upon exposure to UV light in seconds, allowing production line speeds up to 30 fpm. Products create crystal clear bonds and eliminate marking or discoloration that can occur with heat sealing RF or sonic welding. Solvent- and ODC-free, each adhesive comes in standard and thick viscosity grades to suit various dispensing and flow requirements.

Scapa North America    Windsor, CT 06095
Feb 18, 2004 Scapa 512 pressure-sensitive splicing tape consists of polyester film, single-coated with silicone adhesive for use on silicone and other surfaces. Product can withstand prolonged exposure to temperatures as high as 350°F; for shorter periods of time, Scapa 512 withstands temperatures up to 400°F.

Aremco Products, Inc.    Valley Cottage, NY 10989
Feb 18, 2004 Ceramacastâ„¢ 586 is a zirconium-silicate based, phosphate-bonded, chemically-setting ceramic compound suited for bonding and potting infrared heaters, gas igniters, and filters in applications to 2800°F. Product is supplied as powder and mixed with water to paste-like consistency. Pneumatically-dispensed adhesive provides 1-hr pot life and hardening time of 6-8 hr. Dielectric strength and volume resistivity are 220 V/mil and 10¹¹ ohm-cm, respectively.

Tra-Con, Inc.    Bedford, MA 01730
Feb 18, 2004 Amber-colored, medium-viscosity LX30068 cures at room temperature, and offers heat cure option for applications where accelerated cure is desired. Rubber-like epoxy bonds difficult-to-bond materials in addition to traditional metals, plastics, and ceramics. It performs at high temperatures during thermal cycling and long-term exposures.

Huntsman Advanced Materials    Los Angeles, CA 90039
Feb 17, 2004 Offering 55 min work life, UV-absorbing Araldite® AAY-8591 resin/HY-8591 hardener system cures after 60 min at 158°F, 20 min at 212°F, or 5 min at 302°F. With elevated temperature cure, it exhibits lap shear strength of ~2,200 psi and Shore hardness of 65D. Low-viscosity, easy-to-spread epoxy bonds glass to glass and metals to ceramics. It is suited for manufacturing welding helmets and other products in which UV transmission issues are important.

TruSeal Technologies Inc.    Beachwood, OH 44122
Feb 11, 2004 PURFECT GLAZEâ„¢ warm applied adhesive glazing sealants bond glass to window sashes or frames. Sealant technology utilizes polyurethane reactive hot-melt adhesives and allows users to wrap windows within 5 min. Once glass is bedded, products provide immediate handling strength. Sealants are available in 3 grades: PURFECT GLAZE G for general insulating glass (IG) applications, SA for special IG applications, and H for high-strength IG applications.

Scapa North America    Windsor, CT 06095
Feb 11, 2004 Scapa 440 Series tape, suited for taping, bundling, and sealing applications, is made of polyethylene coated cloth single-coated with high-tack, natural rubber adhesive. Product does not exhibit edge ooze, can be torn by hand, will not twist or curl during application, and adheres to poly films and sheeting. Scapa 441 is 7.0 mil thick, Scapa 442 is 8.5 mil thick, and Scapa 448 is 11.0 mil thick.

Bostik Findley, Inc.    Middleton, MA 01949-2128
Feb 10, 2004 Bostik® 2175 FS environmentally-sound, 100% solids sealant meets demands of transportation industry. Based on silyl polyurethane sealant hybrid polymer technology, sealant is suited for overhead and vertical seam-sealing and gap-filling applications. Non-yellowing, paint-compatible formula adheres to aluminum, wood, and FRP. It is free of xylene, acetone, MEK, and similar solvents. At 70°F, moisture-curing product is tack-free in 20-40 min and fully cures in 24-36 hr.

Tra-Con, Inc.    Bedford, MA 01730
Feb 06, 2004 Silicone-based TRA-CAST 813J01 bonds well to difficult substrates, exhibits low stress, and can cure at room temperatures. Soft and flexible material has medium viscosity prior to cure. Once hardened, adhesive can handle temperatures up to 260°C without reverting. It has low Tg and work life of over 1½ hours. Typical applications include encapsulation of heat sinks, transistors, and power sources.

Master Bond, Inc.    Hackensack, NJ 07601
Feb 05, 2004 Two-component, electrically-isolating, EP21AO epoxy adhesive will adhere to similar and dissimilar substrates. Self-leveling paste is 100% reactive and does not contain solvents or volatiles. It has thermal conductivity of 10 BTU/in./ft²/hr/°F and dielectric strength greater than 400 V/mil. Available in pt, qt, gal, and 5-gal kits, product features Shore D hardness greater than 85, tensile strength of 5,000 psi, and operating temperature of -60 to +250°F.

Devcon    Danvers, MA 01923
Feb 04, 2004 ZipGrip® adhesives consist of clear-drying cyanoacrylates that bond plastics, rubber, and metal; provide flexibility and impact resistance; and withstand service temperatures to 280°F. Able to attain fixture strength in seconds, adhesives reach functional strength in 60 min and full cure in 24 hr. ZipGrip HV1200 has 1,200 cps viscosity and 3,700 psi tensile shear strength, while ZipGrip HV2200 has 2,200 cps viscosity and 3,800 psi tensile shear strength.