Wireless Transceiver supports 3GPP LTE/WCDMA/EGPRS phones.June 15, 2010 -
Optimized for compressed mode operation, MB86L10A transceiver features quad-band GSM/EDGE and up to 5 WCDMA or LTE bands in single-phone configuration. It includes 8 outputs that directly drive power amplifier, eliminating need for TX SAW filters, and receiver also incorporates anti-aliasing filters, digital channel filters, digital gain control, and high-dynamic-range ADCs. Microcontroller simplifies timing and control, and RF API programming speeds radio integration time.
(Archive News Story - Products mentioned in this Archive News Story may or may not be available from the manufacturer.)
Original Press release
Fujitsu Microelectronics Inc.
3545 N. 1st St.
San Jose, CA, 95134 1804
USA
Fujitsu Microelectronics Introduces Industry's First 3G and LTE SAW-Less Transceiver
Providing a New Multimode, Multiband LTE/UMTS/GPRS/EDGE Solution in a Compact, Single-chip, Including Open Standard Digital Interface for 4G/3G/2G Multimode Phones
SUNNYVALE, Calif -- Fujitsu Microelectronics America, Inc. (FMA) today introduced the industry's first transceiver that supports 3GPP LTE/WCDMA/EGPRS wireless phones.
The Fujitsu MB86L10A transceiver eliminates 3G and LTE TX and RX interstage SAW filters and low-noise amplifiers (LNAs). The single-chip transceiver features backward compatibility with a high-level programming model (API) for radio control using DigRF/MIPI D3G and D4G open standard digital interfaces. This makes the new MB86L10A compatible with a wide range of industry basebands.
The compact module enables cell phone manufacturers to reduce component count, board space and total bill of materials. Its simplified programming model significantly reduces development time and simplifies integration of the RF in a radio platform. The transceiver, which is optimized for compressed mode operation, features quad-band GSM/EDGE and up to five WCDMA or LTE bands in a single-phone configuration.
The MB86L10A includes eight outputs that directly drive the power amplifier, eliminating the need for TX SAW filters while simultaneously supporting advanced multimode PAs. The receiver provides nine inputs that support LTE, WCDMA and GSM/EDGE. The new RF front-end eliminates the need for LNAs and SAW filters. Five additional ports enable RX diversity in WCDMA and LTE modes. The receiver also incorporates anti-aliasing filters, digital channel filters, digital gain control and high-dynamic-range ADCs.
The MB86L10A supports GSM (GSM850, EGSM900, DCS1800, PCS1900), WCDMA (Bands I, II, III, IV, V, VI, VIII, IX, X and XI) and LTE (FDD Bands 1, 3, 4, 6, 7, 8, 9, 10, 11, 13, 17 and TDD band 38 or 40). The transceiver includes dual 3G and 4G DigRF interfaces to the baseband IC to support the latest as well as legacy generations of basebands, SPI and/or GPOs control PAs, switching regulators and antenna switches. A microcontroller in the transceiver simplifies timing and control.
"The Fujitsu MB86L10A LTE multimode transceiver is the first of its kind to eliminate LNAs and 3G/4G TX and RX SAWs, reducing board area, component count and cost," said Vivek Bhan, senior director of RF Engineering and Product Development for Fujitsu Microelectronics America. "This LTE multimode RF transceiver supports most global band configurations and standard interfaces, and its simple RF API programming reduces radio integration time. The result is smaller radios with optimal time to market for handset manufacturers worldwide."
MB86L10A Now in Pre-Production Field Trials
The new MB86L10A adds to the company's leadership in the mobile phone RF transceiver market, following the September 2009 introduction of the first commercial multimode 2G/3G SAW-less transceiver, the MB86L01A. (See related press release, http://www.fujitsu.com/us/news/pr/fma_20090914.html.)
The MB86L10A transceiver is in pre-production phase and is supporting field trials at a major carrier. The field trial is exercising the new device in 2G, 3G and 4G modes across multiple bands and both DigRF interfaces.
"It's fantastic to receive direct feedback from leading LTE carriers," said Bhan. "The early feedback on an advanced new standard will help develop a stable product faster, speeding time to market."
Availability
Samples of the MB86L10A manufactured in 90nm CMOS process technology are available now in 230-pin, 6.5 mm x 9.0 mm x 0.9 mm LGA packages. Volume pricing is available upon request.
About Fujitsu Microelectronics America, Inc.
Fujitsu Microelectronics America, Inc. (FMA) leads the industry in innovation. FMA provides high-quality, reliable semiconductor products and services for the wireless, automotive, consumer, and other markets throughout North and South America. For product information, visit the company's web site at http://us.fujitsu.com/micro/rftransceiver, address e-mail to inquiry@fma.fujitsu.com or call 1-800-866-8608.
|
|
|
|
|
|
|
|
