Unidirectional Reinforcement Tape aids composite parts formation.

Press Release Summary:




DiscoTape(TM) - discontinuous, unidirectional preimpregnated reinforcement tape (unitape) - can stretch up to 30% to form complex shapes. Used in formation of composite parts with complex curvatures normally precluding use of unitape without cutting and darting, product can be made with glass or carbon fiber prepregged with epoxy resins or thermoplastics. Mechanical testing shows knockdown of 0° tensile strength while interlaminar shear and in-plane shear remain relatively consistent.



Original Press Release:



Pepin Associates Introduces Discontinuous Unidirectional DiscoTape(TM)



GREENVILLE, ME: Pepin Associates, Inc. has developed a discontinuous, unidirectional preimpregnated reinforcement tape (unitape) which has the ability to stretch up to 30% to form complex shapes. The material, called DiscoTape(TM) (subject of provisional patent), has shown promise in the formation of composite parts with complex curvatures normally precluding the use of unitape without cutting and darting. The material can be made with glass or carbon fiber prepregged with epoxy resins or thermoplastics. Variations of fiber lengths and segmentation patterns have been investigated to optimize DiscoTape for a variety of applications.

Two project engineers at Pepin Associates have conducted research on DiscoTape to ascertain its mechanical properties as compared to continuous tape, determine its forming limits and evaluate its use for composite structures such as keels, frames, fairings and radomes.

Mechanical testing conducted by Project Engineer Amber Simmons shows that while there is a knockdown of 0° tensile strength in the discontinuous unitape, interlaminar shear and in-plane shear remain relatively consistent with those properties of continuous unitape. Tensile modulus is also close to continuous reinforcement values. This would allow use of DiscoTape in structures whose designs are stiffness driven such as bead stiffened shear panels. The ability of the discontinuous unitape to stretch and form complex parts, such as the hemisphere featured in Photo #1, could enable manufacturers to use unitape where it hasn't been used in the past.

One possible application for DiscoTape is radomes. These fiber-reinforced composite structures are used to protect radar equipment on aircraft and rotorcraft during flight. The extreme environments these structures must endure during all aspects of flight, especially for military platforms, require strength and durability. However, these same structures must be as close to transparent as possible in allowing radar frequencies to penetrate the structure.

Pepin Associates Project Engineer Elizabeth Thompson has completed a study on the formability and transmissivity of glass DiscoTape, applicable for use in radome manufacture. Elizabeth formed test specimens of discontinuous glass prepreg unitape (DiscoTape) and Pepin Associates contracted with Radant Technologies of Stow, Massachusetts to measure the electrical properties of these specimens.

Pepin Associates, Inc. has shown that discontinuity does not always affect transmissivity of the radar signal. It was found that the discontinuity may interfere with the signal at X-band frequencies. In the event the material is showing signal loss, the length of DiscoTape segments can be altered easily, allowing the fabricator to 'tune' the material as needed. The research showed no appreciable effect on the material transparency for the Q-band frequency. Elizabeth Thompson details these conclusions in her technical paper, which will be presented at the 2012 SAMPE Conference in Baltimore, MD.

These results are promising because radome shapes are as variable as the aircraft on which they are mounted. Aircraft and rotorcraft radomes all have a cone or hemispherical component which is a challenge to fabricate with fiber-reinforced composite materials. Forming such complex curvatures with continuous, unidirectional tape is a challenge due to wrinkling of the material. Wrinkles can degrade both the radar signal and radome structural integrity. Applying unidirectional reinforcement tape to fabricate these parts without wrinkles is difficult and time consuming: DiscoTape could allow the formation of these shapes without wrinkling.

DiscoTape has the potential to be used on many other structures ranging from wind blades to medical imaging equipment to structures for aircraft and rotorcraft. Pepin Associates is seeking to evaluate DiscoTape applications for hard-to-form parts and structures commonly made with continuous unitape. The part shown in Photo #2 is the secondary structure of a modern military jet, formed with carbon fiber DiscoTape.

"We believe the forming capabilities of DiscoTape will provide a significant manufacturing advantage in terms of time savings and reduction of scrap material versus the use of continuous unitape", said John Pepin, President of Pepin Associates. "There is more development work to be done, but our initial results are very promising", Pepin added.

The ability of this discontinuous unitape to form complex parts has drawn the attention of Tom Campbell, Applications Engineer at Fiberforge, Inc. Colorado-based Fiberforge is a technology company that has developed a patented manufacturing process for continuous fiber-reinforced thermoplastic parts. As a leader in thermoplastic advanced composites, Fiberforge delivers cost-effective solutions for manufacturing high-performance products. Fiberforge offers manufacturing equipment, production of composite parts and engineering services to meet their client's needs. Tom Campbell is evaluating a thermoplastic version of DiscoTape for possible use in aerospace applications.

"Fiberforge sees significant potential in the DiscoTape process in forming complex parts from thermoplastic composites. The possibility of discontinuous forming behavior in a nearly continuous material is very intriguing and we look forward to exploring the possibilities and bounds of this new material format." stated Campbell.

Technical papers on DiscoTape will be presented by Project Engineers Amber Simmons and Elizabeth Thompson at the 2012 SAMPE Conference May 22-24 in Baltimore. Exhibits by Fiberforge (booth 208) and Pepin Associates (booth 1545) will be on display.

All Topics