Tool Calibrator helps align/verify CNC punch press turret.
July 12, 2005 -
Designed to verify and restore angular alignment of turret press punching stations, Pilot(TM) Tool Calibration System consists of matched set of upper and lower interlocking components loaded into machine's turret upper and lower chambers. It operates in Verification and Alignment modes and features tri-color indicator lights to warn when system is not aligned, aligned angularly and concentrically within 0.012 in., or aligned angularly and concentrically within 0.0003 in.
(Archive News Story - Products mentioned in this Archive News Story may or may not be available from the manufacturer.)
Original Press release
Mate Precision Tooling
1295 Lund Boulevard
Anoka, MN, 55303
USA
Mate Precision Tooling Introduces The Mate Pilot(TM) -- A New Tool Calibration System For Aligning And Verifying CNC Punch Press Turret Precision
Call 1-800-328-4492 For FREE Brochure
Anoka, Minnesota: Mate Precision Tooling leads the punching industry with another "first" - the Mate Pilot(TM) Tool Calibration System. Designed to verify and restore the angular alignment of punching stations of a turret press, this system is highly accurate and easy to use.
The Pilot Tool Calibration System provides punch press users with an effective and reliable means for maintaining top punch press performance while safeguarding tooling and eliminating scrapped parts because of turret alignment problems.
System Ensures Precision Concentric And Angular Tool Component Alignment
Consisting of a matched set of upper and lower interlocking components, which are loaded into the machine's turret upper and lower chambers, the system operates in two modes:
Verification mode - Confirms the precise concentric and angular alignment of the punch press turret to maintain high quality piece part production and maximum tool life.
Alignment mode - Restores the concentric and angular alignment of each station with the same precision as the initial machine installation.
System Is Easy And Fast To Use
Simply install the two halves of the calibration instrument into the press turret station to be aligned. Then rotate the turret to position the station to be aligned under the machine's ram. Tighten the integral adjustment handle which draws the two halves of the calibration instrument together.
As this engagement occurs, the interlocking design of the interface causes the loosened die holder assembly to draw precisely together into concentric and angular alignment relative to the upper bore of the turret.
During this process, tri-color indicator lights on the top of the instrument signal alignment. When the indicator shows: Red - system is not yet aligned; Yellow - system is aligned angularly and concentrically within 0.012 inch / 0.030 mm; Green - system is aligned angularly and concentrically within 0.0003 inch / 0.008 mm (recommended when punching materials 0.078 inch / 2.00 mm thickness or less).
High Precision Components Ensure Accuracy, Long Life
Like Mate's high precision, long-life tooling, the Mate Pilot Tool Calibration System is quality manufactured to provide years of alignment service thereby ensuring top punch press and tool performance. Each calibration instrument is machined from a single piece of the highest quality tool steel. Upper and lower halves of the instrument are separated near the end of the production process and just prior to the installation of hardware. This ensures that the two components are a precisely matched set with high accuracy, thereby eliminating any possibility of cumulative tolerances adversely affecting instrument accuracy.
Mate Pilot Tool Calibration Sets Available For Amada And Finn Power Presses
Mate Pilot Tool Calibration sets are available for Amada thick turret and Finn Power presses in: A Station ˝ inch (12.70 mm), B Station 1-1/4 inch (31.80 mm), C Station 2 inch (50.80 mm), D Station 3-1/2 inch (88.90) and E Station 4-1/2 inch (12.70 mm). Accessory kits consisting of alignment and adjusting bars are required that work with any station size.
For a FREE Mate Pilot(TM) Tool Calibration Tool system brochure, call 1-800-328-4492.
See at mate.com/pilot
Email: marketing@mate.com
Or write to MATE PRECISION TOOLING, 1295 Lund Boulevard, Anoka, Minnesota 55303. USA and Canada, Fax 1-800-541-0285. Outside USA and Canada, call 1-763-421-0230 Fax 1-763-421-0285.
|
|
|
|
Newsletters |
Industry
Market Trends
Has Got It |
- Latest developments
- Trends
- Best practices
- Opinions & Commentary
|
 |
Get Ahead.
Get IMT.
Subscribe Free Today
Subscribe View
Sample |
Your Gateway to a Fast
Changing World
Product News Alerts |
 |
Receive similar stories and other customized
news to keep you in the know on the products shaping
industry. |
Subscribe Free Today
Subscribe View
Sample |
|
|
|
|
|
|
|
|
|
| 
