Receiver Subsystem combines high-speed ADCs and drivers.
June 12, 2009 -
Housed in 11.25 x 15 mm LGA uModule® package, Model LTM9002 combines dual 14-bit ADC sampling up to 125 Msps, anti-aliasing filters, fixed gain differential ADC drivers, and 12-bit trim DACs. Dual IF/baseband receiver subsystem achieves 90 dB isolation at 140 MHz input frequency. Overall gain is typically 26 dB and varies less than 0.1 dB between 2 channels. Utilizing multi-layer substrate, package shields sensitive analog lines from digital traces to minimize digital feedback.
(Archive News Story - Products mentioned in this Archive News Story may or may not be available from the manufacturer.)
Original Press release
Linear Technology Corp.
1630 McCarthy Blvd.
Milpitas, CA, 95035
USA
Dual-Channel uModule Receiver Subsystem Combines High-Speed ADCs & Drivers in Compact Package
MILPITAS, CA - June 9, 2009 - Linear Technology introduces the LTM9002, a dual IF/baseband receiver subsystem that includes a high performance dual 14-bit Analog-to-Digital converter (ADC) sampling up to 125Msps, anti-aliasing filters, fixed gain differential ADC drivers and 12-bit, trim Digital-to-Analog converters (DACs). The integrated receiver significantly reduces the board space and development time for wireless base stations implementing I/Q receivers, direct conversion receivers or multi-channel configurations including diversity receivers. The LTM9002 harnesses years of applications experience and wraps it into an easy-to-use 11.25mm - 15mm uModule® package.
Extensive hands-on applications experience is a prerequisite for any designer hoping to take full advantage of an ADC's capabilities when sampling high dynamic range signals in high-speed communications receivers, communications test equipment or instrumentation. Multichannel applications have several unique requirements, such as channel matching and channel-to-channel isolation. The LTM9002 pays careful attention to these design considerations to provide the optimal connection between the RF and digital domains. Designers no longer need to perform the time consuming tasks of component selection, input impedance matching, filter design and layout, while also eliminating the long hours of troubleshooting and thereby reducing time to market.
For multichannel applications, channel-to-channel matching and isolation are important considerations. The LTM9002 achieves 90dB isolation at 140MHz input frequency despite the small form factor. The overall gain is typically 26 dB and varies less than 0.1 dB between the two channels. A thoughtful addition, a dual 12-bit auxiliary DAC offers the flexibility to adjust the span and perfectly balance the two channels using an SPI-compatible serial port.
The LTM9002 is packaged in a space-saving 11.25mm x 15mm LGA package, utilizing a multi-layer substrate that shields sensitive analog lines from the digital traces to minimize digital feedback. Supply and reference bypass capacitance is placed inside the module tightly coupled to the die, providing a space, cost and, more significantly, a performance advantage over traditional packaging. With no external capacitance required, the LTM9002 consumes approximately one-fourth the space of the discrete implementation.
The LTM9002 is available in production volumes today and is priced at $99.25 each in 1,000 piece quantities. For more information, visit www.linear.com.
Summary of Features: LTM9002
Integrated Dual 14-Bit, High-Speed ADCs, Passive Filter & Fixed Gain, Differential Amplifiers
Up to 300MHz IF Range
Low-Pass & Band-Pass Filter Versions
Integrated Low Distortion Amplifiers
Fixed Gain: 8dB, 14dB, 20dB or 26dB
50Ohm, 200ohm or 400ohm Input Resistance
66dB SNR up to 70MHz input
76dB SFDR up to 140MHz input
Auxiliary 12-Bit DACs for Full-Scale Adjustment
Clock Duty Cycle Stabilizer
Single 3V to 3.3V Supply
Low Power: 1.3W (665mW/ch.)
Shutdown & Nap Modes
11.25mm x 15mm LGA Package
About Linear Technology
Linear Technology Corporation, a manufacturer of high performance linear integrated circuits, was founded in 1981, became a public company in 1986 and joined the S&P 500 index of major public companies in 2000. Linear Technology products include high performance amplifiers, comparators, voltage references, monolithic filters, linear regulators, DC-DC converters, battery chargers, data converters, communications interface circuits, RF signal conditioning circuits, µModule® products, and many other analog functions. Applications for Linear Technology's high performance circuits include telecommunications, cellular telephones, networking products such as optical switches, notebook and desktop computers, computer peripherals, video/multimedia, industrial instrumentation, security monitoring devices, high-end consumer products such as digital cameras and MP3 players, complex medical devices, automotive electronics, factory automation, process control, and military and space systems.
LT, LTC, LTM and µModule are registered trademarks of Linear Technology Corp. All other trademarks are the property of their respective owners.
Worldwide Contacts
North America and General Information
John Hamburger
Tel: (408) 432-1900 ext. 2419
jhamburger@linear.com
Doug Dickinson
Tel: (408) 432 1900 ext. 2233
ddickinson@linear.com
|
|
|
|
|
|
|
| 
