Low-Profile Surface Microphone operates on planar/curved surfaces.
July 21, 2010 -
Endevco® model EM40PS enables acoustic measurements on planar and curved surfaces exposed to air slipstreams. It features ISOTRON®, IEPE-type amplifier; dust-free, water-repellant grid cap; and can be laid flat on its 2 in. dia rubber pad or surface-mounted using double-sided adhesive pad. Front vent by side of diaphragm enables pressure equalization. Operating in temperatures from -4 to +176ºF, microphone has sensitivity of 5 mV/Pa at 250 Hz and audio frequency range of 20 Hz to 20 kHz.
(Archive News Story - Products mentioned in this Archive News Story may or may not be available from the manufacturer.)
Original Press release
Meggitt Sensing Systems (Endevco Corp.)
30700 Rancho Viejo Rd.
San Juan Capistrano, CA, 92675
USA
Meggitt Sensing Systems Introduces New Endevco® Low-Profile Surface Microphone with Integral ISOTRON® Amplifier and TEDS
San Juan Capistrano, California, USA - Meggitt Sensing Systems (www.meggittsensingsystems.com), a Meggitt group division, has announced the new market introduction of the Endevco® model EM40PS, a low-profile surface microphone with integral ISOTRON® (IEPE-type) amplifier and TEDS, designed to facilitate simplified larger channel count acoustic measurements on typical planar and curved surfaces exposed to air slipstreams.
The robust design of model EM40PS requires no microphone holders or stands, and incorporates a dust-free, water-repellant grid cap and a lightweight, detachable silicon rubber fairing, allowing for near-flush mounting on curvilinear surfaces and mounting pads. Models also include an integral 3.3 ft (1 m) coaxial cable with microdot connector. Units offer a nominal sensitivity of 5 mV/Pa (@ 250 Hz), wide audio frequency range from 20 Hz to 20 kHz and large dynamic range from <30 dBA to 136 dB over an operating temperature range of -20ºC to +80ºC (-4ºF to +176ºF) with low sensitivity to base bending. Because of its lightness, the EM40PS contributes very little mass to thin plates, and can be laid flat on its 2" (51mm) diameter rubber pad, or surface mounted using a double-sided adhesive pad for automotive, aeronautical, general acoustics and sound pressure level testing requirements. Pressure equalization is via a vent placed at the front of the microphone by the side of its diaphragm, important for both aircraft usage and on-road vehicle measurements in mountainous country. Close manufacturing tolerances and the advantages of TEDS enable the microphone to offer a high degree of interchangeability, precluding the need for accounting of individual characteristics.
Recommended accessories for the Endevco® model EM40PS include the model EM42AA handheld pistonphone calibrator; the model 4416B constant-current power supply (2-20mA); and the model 133 signal conditioner. With its unique size and performance characteristics, the Endevco® model EM40PS is ideal for measuring wind-induced noise on ground and airborne vehicles; acoustic radiation surface measurements; wind tunnel noise testing; and for making internal vs. external noise measurement comparisons on moving vehicles. For detailed technical specifications, drawings or additional information, visit www.meggittsensingsystems.com.
About Meggitt Sensing Systems
Meggitt Sensing Systems, a Meggitt group division (www.meggitt.com), is a leading supplier of high-performance sensing and monitoring systems for physical parameter measurements in extreme environments. It has operated since 1927 through its antecedents-ECET, Endevco, Ferroperm Piezoceramics, Lodge Ignition, Sensorex, Vibro-Meter and Wilcoxon Research-whose portfolios form the basis of product lines offered by today's Meggitt Sensing Systems. Meggitt's Endevco® range of piezoelectric, piezoresistive, Isotron® and variable capacitance accelerometers, piezoresistive pressure transducers, acoustic sensors, electronic instruments and calibration systems ensure critical accuracy and reliability within aerospace, automotive, defense, industrial, medical, power generation, R&D, space and test and measurement applications. Endevco® and Isotron® are registered trademarks of the Meggitt group.
|
|
|
|
|
|
|
| 
