Hand-Held Calibration System features modular design.July 2, 2008 -
Advanced Modular Calibration System includes 3 discrete components which can be used as stand-alone instruments. Rugged and weatherproof multi-function DPI 620 calibrator can measure and source mA, mV, V, Ohms, frequency, and variety of RTDs/thermocouples. Interchangeable pressure measurement modules attach to calibrator via carrier, while 3 pressure stations enable generation of pneumatic/hydraulic pressure from 95% vacuum to 20 or up to 100 bar and 0-1,000 bar, respectively.
(Archive News Story - Products mentioned in this Archive News Story may or may not be available from the manufacturer.)
Original Press release
GE Sensing
1100 Technology Park Dr.
Billerica, MA, 01821
USA
New Modular, Hand-Held, Test and Calibration System from GE
June 9, 2008
The new Advanced Modular Calibration System from GE Sensing & Inspection Technologies is a hand-held test and calibration system that combines an advanced, multi-function calibrator with world class pressure measurement and generation capability. Its modular concept allows its discrete components to be used as stand-alone instruments, allowing significant flexibility both in cost of ownership and in functionality.
The Advanced Modular Calibration System uses three basic components to perform duties formerly requiring a wide range of different instruments. At its core is its advanced, electrical, frequency and temperature calibrator. This compact and robust multi-function unit can measure and source mA, mV, V, Ohms, frequency and a variety of RTDs and thermocouples. Pressure measurement is provided by interchangeable pressure modules that attach to the calibrator via a carrier. The calibrator and the pressure modules can also attach to a pressure generation station to form a fully integrated, high performance pressure calibrator. Three pressure stations are available, enabling the generation of pneumatic pressure from 95% vacuum to 20 bar or up to 100 bar while hydraulic pressure capability is 0 to 1000 bar.
The system's rugged and weatherproof multi-function DPI 620 calibrator has been designed with performance, ease of use and versatility in mind. It is two to three times smaller, weighs less than a third of its nearest competitor and yet has one of the largest and brightest displays. Its video quality color touch screen shows only those buttons necessary for the immediate, selected task. The buttons are big enough to permit operation by a gloved hand. The display itself can be configured to show up to six reading windows, which also act as active keys and, when pressed, expand to show more detailed information or to provide advance functions. Color-coding of displays is incorporated to facilitate fast sentencing.
The calibrator can be simply expanded by the addition of further hardware and software modules, including an Intecal field calibration and documentation manager, a wireless module and a 300 Vac measurement probe. It is fitted with a HART configurator as standard to provide digital communication with HART devices for interrogation, configuration and calibration. The DPI 620 is also available in a Windows CE-driven version, providing all the computing power of a conventional hand-held PC or PDA. The DPI 620CE provides standard Windows applications and file management and allows the user to view PDF files and jpeg images, such as user manuals, data sheets and installation drawings, while in the field or on the plant.
The pressure modules represent the latest in digital output sensor technology, incorporating a number of key innovations to allow pressure re-ranging of compatible equipment. Digital characterization and a simple screw fit allow interchangeability in a matter of seconds with no need for tools, set-up or calibration. The modules can be located in the module carrier that can then be connected to the multi-function calibrator, to form a compact, hand-held test tool. Alternatively, the pressure modules can be located in the relevant pressure generation station to which the DPI 620 also locks in place to create a self contained pressure calibrator . Each of the pressure generation stations can also act in a stand-alone capacity to replace hand pumps and comparators. They are all simple to operate by hand and each represents a significant step forward in pressure generation technology. The 20 bar station features a conventional hand pump, volume adjuster and pressure/vacuum selector but will generate pressure with half the effort of conventional systems. The 100 bar pneumatic station represents a five fold increase in capability and solves the transportation and EHS issues of using gas bottles and regulators as a pressure source, while the 1000 bar hydraulic system generates pressure without priming into virtually any system volume thus avoiding the mess and wastage of bleeding open systems. Each station can be fitted with an overpressure protection device to protect both the pressure module and the device under test.
Available with a range of accessories, including soft carry cases and rigid transit solutions, the new modular system is expandable and adaptable to meet changing business and application requirements. A user can begin with the multi-function calibrator and then add pressure capability and other modularity over time. It offers significant cost savings through reduced inventory, user training and maintenance. The system has also been designed to cater for future system integration and incorporates USB and wireless connectivity and a micro SD memory slot.
About GE Sensing & Inspection Technologies
GE Sensing & Inspection Technologies is part of GE Enterprise Solutions, a $5 billion business helping customers compete and win in a changing global environment by combining the power of GE's unique expertise and intelligent technology to drive customers' productivity and profitability. GE Sensing & Inspection Technologies is a leading innovator in advanced measurement, sensor-based and inspection solutions that deliver accuracy, productivity and safety to its customers. The company designs and manufactures sensing instruments that measure temperature, pressure, moisture, gas and flow rate for demanding customer applications. It also designs, manufactures and services inspection equipment, including radiographic, ultrasonic, remote visual and eddy current, that monitors and tests materials without disassembly, deforming or damaging them. GE Sensing & Inspection's products are used in a wide range of industries, including oil & gas, power generation, aerospace, transportation and
healthcare. The company has 4,700 employees at more than 40 facilities in 25 countries worldwide.
For more information, visit www.gesensing.com or www.ge.inspectiontechnologies.com
Contact Name: Harish Kumar
E-mail: harish.kumar1@genpact.com
Company Name: GE Sensing
Address 1: 1100 Technology Park Drive Billerica, MA 01821-4111
Country: USA
Phone: 978 437 1000
URL: http://www.gesensing.com
|
|
|
|
|
|
|
| 
