DC-LVDT Gaging Probes are designed for optimal linearity.February 13, 2007 -
Available in ranges of 0.100-4.00 in., GHSE/GHSER 750 Series 19 mm dia sensors are constructed of stainless steel and hermetically sealed. Spring-loaded sleeve bearing results in measurement repeatability of 0.000025 in. Along with ½-20 threaded front end, 24 V sensors come in ready-to-use package for position measurement in gaging applications. Max linearity error is +0.10% FS output, and pre-calibrated 0-10 Vdc output operates with PLCs, digital indicators, and DAQ systems.
(Archive News Story - Products mentioned in this Archive News Story may or may not be available from the manufacturer.)
Original Press release
Macro Sensors
7300 US Route 130 North, Bldg. 22
Pennsauken, NJ, 08110 1334
USA
DC-LVDT Gaging Probes Offer Highest Linearity
Pennsauken, NJ, February 2, 2007... Macro Sensors, (www.macrosensors.com), a sensor company specializing in the manufacture of LVDT-based linear sensors and gaging probes, introduces a line of 24V spring-loaded position sensors that offer the industry's most accurate position measurement with maximum linearity error of +0.10% of full scale output. Available in ranges of 0.100 inches (2.5 mm) to 4.00 inches (100 mm), the American-made GHSE/GHSER 750 Series sensor is offered in a ready-to-use package for position measurement in gaging applications. Units can be installed in hostile environments, while their wiring is connected to power supplies, indicators and controllers located in remote, safe environments.
Units consist of a spring-loaded sleeve bearing that results in measurement repeatability of 0.000025 inches (0.6 µm) The spring-loaded assembly, along with a 1/2-20 threaded front end, makes mechanical set-up of the sensor into automated machinery less complicated and more cost effective than other sensor configurations. Electrical termination of the GHSE 750 Model is made through a sealed axial connector while the electrical termination for the GHSER 750 is through a radially- mounted sealed connector for a much reduced installed length.
The probe shaft fully extends by a spring exerting a nominal force of 6 to 20 ounces, depending upon total range. As an air extend, spring-retract unit, the probe shaft of Macro Sensors' GHSE/GHSER 750-A gaging probes fully extends when pressurized by air but retracts to get out of the way during unloading/unloading operations or to provide clearance for products on an assembly line.
Built-in electronics result in a position sensor that operates from DC inputs of 15-24V DC and generates a pre-calibrated 0-10 Volt DC output. The output from the GHSE 750 Series is designed to operate with most PLCs, digital indicators, data acquisition systems. Units can be operated directly from a typical PLC's 24 Volt power, providing added convenience on the shop floor.
Constructed entirely of stainless steel, these hermetically-sealed 19 mm diameter sensors provide long service life in various industrial uses such as industrial gaging systems, electronic dial indicators, fabricated metal products gaging, materials testing apparatus as well as large shaft TIR measurement. Hermetically sealed LVDT-based gaging probes can withstand the effects of dirt, water, steam and other corrosive elements without effecting its performance.
Pricing for the GHSE/GHSER 750 Series begins at $541. For additional information, please contact Eileen Otto at 856-662-8000/email: sales@macrosensors.com or visit our web site at http://macrosensors.com/ms-lvdts_prod-lvdt-spring-dc.html
About Macro Sensors
Macro Sensors' extensive line of LVDT-based linear and rotary sensors are used for linear position measurement and feedback in a variety of industrial applications including factory automation, motion control systems, metal fabricating, automotive assembly as well as power plants, gas/steam turbines. Incorporated in 1994, the Company offers more than 200 years of cumulative design and manufacturing experience by its key staff in serving its OEM and end-user international customer base. On June 1, 2005, Macro Sensors was acquired by AST, manufacturer of state-of-the-art Micro-Electro- Mechanical- Structures (MEMS) based pressure sensors, transducers, and transmitters. Common applications of AST sensor products are in industrial OEM, hydraulic systems, fuel cells, medical gases, HVAC/R, refrigeration, oil & gas exploration/production, and off-road vehicles. For more information on AST products and technology, visit the AST website at www.astsensors.com.
U.S. Route 130 North, Bldg. 22, Pennsauken, NJ 08110-1541
Tel: 856-662-8000 Fax: 856-317-1005
|
|
|
|
|
|
|
| 
