Analog FET Pre-Driver addresses automotive motor control.
November 20, 2007 -
Supplied in Pb-free packaging, MC33927 enables precision control of 3-phase motor speed, torque, and power in automotive and industrial applications. This field effect transistor (FET) pre-driver supports 6-58 V range, offers programmable dead time delay from 0 to more than 10.5 µsec, and is capable of 0-100% PWM control of load. Product interfaces to 5.0 or 3.0 V MCU via 6 direct input control signals, SPI port, and asynchronous reset, enable, and interrupt signals.
(Archive News Story - Products mentioned in this Archive News Story may or may not be available from the manufacturer.)
Original Press release
Freescale Semiconductor
6501 WILLIAM CANNON DRIVE WEST
AUSTIN, TX, 78735-8598
USA
Freescale Delivers Comprehensive, Cost-Effective Analog Pre-Driver for Automotive Motor Control
Field effect transistor with industry's widest voltage range is designed to support broad automotive application spectrum
AUSTIN, Texas - Nov. 19, 2007 - Freescale Semiconductor, the leading supplier of semiconductors to the automotive industry, has introduced a versatile field effect transistor (FET) pre-driver designed for three-phase motor control in a wide range of automotive and industrial control applications.
The MC33927 pre-driver provides a cost-effective, comprehensive solution for cooling fans, water pumps, fuel pumps, and electro-hydraulic and electric power steering used in automobiles, electric scooters and electric-assist bicycles. These applications require synchronous and asynchronous three-phase motors to combine high output performance, high reliability and small size for space-constrained designs.
Based on Freescale's SMARTMOS(TM) technology, the MC33927 integrates the following advanced features that help simplify motor control:
Industry's widest voltage range in a single pre-driver device. The device supports the entire automotive range from 6V to 58V, which enables reduced inventory or a single development module for multiple platforms.
Programmable dead time delay. Adjustable delay helps eliminate current shoot through (crossover) and increases performance.
Full pulse width modulation (PWM) range. It can support from 0% to 100% PWM control of the load for increased motor efficiency and control.
Extensive diagnostic and self protection capabilities. The pre-driver provides protection and works in concert with microcontrollers (MCUs).
The MC33927 enables precise and efficient control from less than 6V to more than 55V.
The device's logic interfaces easily with the latest 3V systems, as well as established 5V platforms. The MC33927 interfaces to a 5.0V or 3.0V MCU via six direct input control signals, a serial peripheral interface (SPI) port for device setup, and asynchronous reset, enable and interrupt signals.
"By combining many advanced control features in a single device, the MC33927 is ideally suited for fractional to integral horsepower motor control," said Arman Naghavi, vice president and general manager of Freescale's Analog, Mixed-Signal & Power Division. "Our latest pre-driver provides developers with a high level of flexible control for such capabilities as phase timing, protection and diagnostics."
The device is designed to enable precision control of motor speed, torque and power. The phase control logic prevents both high-side and low-side FETs from conducting simultaneously and has a programmable deadtime from zero µs to more than 10.5µs. This complementary phase control logic can be turned off for explicit control of each driver, a desirable feature for switched reluctance applications.
MC33927 product features
Fully specified from 8.0V to 40V, covering 12V and 24V automotive systems
Extended operating range from 6.0V to 58V, covering 12V and 42V systems
1.0A gate drive capability with protection
Protection against reverse charge injection from CGD and CGS of external FETs
Integrated charge pump to support full FET drive at low battery voltages
Deadtime is programmable via the SPI port
Integrated op amp for current feedback
Simultaneous output capability enabled via safe SPI command
Lead-free packaging
Pricing and availability
Samples of the MC33927 are available upon request. Suggested per-unit resale pricing (USD) for the MC33927 in 10,000-piece quantities is $2.72.
The MC33927 is offered in a compact thermally enhanced package and supported by evaluation boards and a USB to SPI interface board. The KITUSBSPIEVME board enables a personal computer without a parallel port to communicate with other Freescale evaluation boards through a USB port. Suggested resale pricing for the KITUSBSPIEVME is $65 (USD).
For more information about the MC33927, including development tool availability, visit www.freescale.com/files/pr/eng....
About Freescale Semiconductor
Freescale Semiconductor is a global leader in the design and manufacture of embedded semiconductors for the automotive, consumer, industrial, networking and wireless markets. The privately held company is based in Austin, Texas, and has design, research and development, manufacturing or sales operations in more than 30 countries. Freescale is one of the world's largest semiconductor companies with 2006 sales of $6.4 billion (USD). www.freescale.com
Reader Inquiry Response:
Freescale Semiconductor
P.O. Box 17927
Denver, CO 80217 USA
Freescale and the Freescale logo are trademarks or registered trademarks of Freescale Semiconductor, Inc. in the U.S. and other countries. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2007
|
|
|
|
|
|
|
| 
