Metalworking Coolant is compatible with all aerospace alloys.
December 7, 2007 -
Meeting stringent nuclear and aerospace chemical content and machining requirements, TRIM® C350 is suited for machining and grinding of aircraft air frame and power plant parts/components. Using synthetic ester technology, synthetic coolant does not use conventional sulfur or chlorine based EP additives. Product's pH neutral and less than 100 ppm total chloride working solutions provide corrosion and stain resistance even on most sensitive alloys.
(Archive News Story - Products mentioned in this Archive News Story may or may not be available from the manufacturer.)
For Exacting Aerospace Machining and Grinding, Master Chemical Introduces Premium Metalworking Synthetic Coolant, TRIM® C350
TRIM C350 meets stringent nuclear and aerospace chemical content and machining requirements
November 30, 2007, Perrysburg, OH...Master Chemical Corporation introduces a new product for the machining and grinding of aircraft air frame and power plant (A&P) parts and components. TRIM® C350 is the latest in a long series of TRIM® coolants including industry standards like Ti Grind, TRIM® Regular, TRIM® VHP® E200PW, and TRIM SOL® that fulfilled the needs of this special market. TRIM C350 has been designed from the ground up to assist in achieving the low residual stress and "0" corrosion, stain, and residue that is so necessary on air craft parts. These goals were accomplished without any compromises in the area of chemical content.
Extensive laboratory and field testing proves the efficacy of TRIM C350 in machining and grinding various air craft grades of titanium and aluminum. Using proprietary synthetic ester technology, C350 achieves remarkable machining performance without the use of conventional sulfur or chlorine based EP additives. C350's pH neutral and less than 100ppm total chloride working solutions provides superior corrosion and stain resistance on even the most sensitive alloys. Milton Hoff, Master Chemical's VP of Strategic Technology Development comments, "TRIM C350 is compatible with all aerospace alloys including the very sensitive aluminum alloys, like the 7000 series aluminum alloys, which are very sensitive to staining and C350 will not stain them." Another benefit, according to North American Sales Manager, John Jackowski, is the length of time the product lasts in the sump. "C350 runs clean with a lot less operator maintenance and lasts a very long time in the sump, which makes this a great cost savings for the manufacturer."
David Barned, Master Chemical's Product Manager states, "TRIM C350 is the result of the convergence of several of Master Chemical's key strengths: an understanding of and a commitment to its long term aerospace customers, the desire to improve the manufacturing processes of our customers through innovative state-of-the-art metalworking fluids, and our management and ongoing commitment to products that are safe to use and have as little impact on the environment as possible."
When asked to describe TRIM C350 Mr. Barned said, "C350 is a premium synthetic cutting and grinding fluid tailored to the operational, health, safety, and environmental concerns, and requirements of the North American air frame and power plant manufacturers." As formulated it contains no: chlorine or sulfur based EP additives, petroleum oil, NPEs, silicone, nitrides, phenols, copper, triazine, or formaldehyde releasing chemistry and is PRTR compliant. Field testing shows that it foams very little and has great sump life with very low carryoff so it is a pleasure to work with and manage. "C350 will be a great fluid for the aerospace industry," said Mr. Hoff, "it won't generate foam under the high speed machining operations that are very common in the aerospace industry."
Master Chemical is one of the few metalworking suppliers who routinely employs an outside laboratory to do actual health and safety testing on its products. While all TRIM products are very safe to use, TRIM C350, because of its nearly neutral pH and careful formulation, achieved exceptional results and is judged to be very safe to use, both as a working solution and as concentrate.
TRIM C350 is available in a range of sizes including one gallon containers sold by the case, five-gallon pails, 54-gallon drums, 270-gallon recyclable bins, 350-gallon returnable bins, and tank wagon lots. The product is also available in metric containers for Europe and Asia. Visit http://www.masterchemical.com/na_en/f... to learn more about TRIM C350 or call 419.874.7902.
About Master Chemical Corporation
Master Chemical Corporation was founded on November 13, 1951. Since then, working closely with the worldwide metalworking community, Master Chemical Corporation has developed and marketed a full line of specialty cutting and grinding fluids, cutting oils, concentrated washing and cleaning compounds, and rust preventives all under the TRIM® Brand trademark. These products are both environmentally sound and when used in conjunction with Master Chemical's XYBEX® Coolant Recycling and Filtration Systems, are the most durable and stable products available anywhere today. Master Chemical's products are sold through a network of distributors. Visit http://www.masterchemical.com/na_en/d... to locate a distributor near you. For more information about Master Chemical Corporation please visit www.masterchemical.com or call us at 419-874-7902.
Mark W. Scherer
Manager-Communications
Master Chemical Corporation
501 West Boundary
Perrysburg
OH 43551-1200
Phone: 419-724-7729
Fax: 419-725-7529
mscherer@masterchemical.com
Marketing:
Mark W. Scherer Manager, Communications
USA
Phone: 419-724-7729
FAX: 419-725-7529 E-mail this person Company Information: Name: Master Chemical Corporation Address: 501 West Boundary Street City: Perrysburg State: OH ZIP: 43552 Country: USA Phone: 419 874 7902 FAX: 419 874 0684
News provided by ThomasNet Industrial Newsroom® (TIN). TIN is a comprehensive source
of new and timely product information in the industrial marketplace. TIN supplies new product
information to the web sites, e-marketplaces and print publications that serve the
industrial marketplace. For press release submissions please go to
http://news.thomasnet.com/submitpr.html.
BY ACCESSING, BROWSING AND/OR USING THIS WEB SITE AND/OR ANY WEB SITES PROVIDED BY
ProductNews.com, YOU AGREE TO BE BOUND BY THE TERMS OF USE
AGREEMENT.
del.icio.us
DIGG
Facebook
Reddit
StumbleUpon
Twitter
![[Get Copyright Permissions]](http://license.icopyright.net/images/icopy-w.gif){kind=small}
