CMM provides nanometer measurement of large complex parts.
July 23, 2009 -
With measuring volume of 400 x 400 x 100 mm³, multi-probe ISARA 400 3D Coordinate Measuring Machine uses 3 planar mirror laser interferometers to measure position of object on table according to Abbe principle. Base frame consists of 2 granite guiding units, one for X-Y system and one for Z, and air bearing-equipped direct drives for all 3 directions. For all axes, 1D measuring uncertainty is 45 nm, whereas full-stroke 3D measuring uncertainty totals 100 nm.
IBS Precision Engineering Announces CMM for Nanometer Precision Measurement of Large Complex Parts
14 July 2009: IBS Precision Engineering (IBS PE) takes the measurement of large complex parts to nanometer level with the introduction of the multi-probe ISARA 400 3D coordinate measuring machine (CMM). This important development has been achieved by increasing the measuring volume of its ultra precision 3D CMM by a factor of 40 - to 400 x 400 x 100 mm3 - a significant volume in view of the 45 nanometer (nm) 1D measuring uncertainty in all three directions.
Using three planar mirror laser interferometers, ISARA measures the position of an object on a table according to the Abbe principle (ie the functional point is in line with the measuring line to avoid errors in parallax). Positioned in one stiff frame with the probe, the three planar mirror laser interferometers have their virtual intersection point coinciding with the measuring point of the probe
The product table - made from Silicon Carbide (SiC) for its stiffness and thermal stability - is placed on a mirror table that can be moved in X and Y directions over a granite plate using porous media air bearings. A monolithic block of Zerodur deposits the reflective coating directly onto three extremely flat surfaces to form the three mirrors; the mirror block assembly is directly connected to the machine and calibrated within it, allowing for both the flatness and the mutual perpendicularity of each mirror.
Furthermore, the metrology frame containing the three laser interferometers and the probe moves in the Z direction using air bearings, over a granite guiding surface. The interferometers always point to the centre point of the probe tip (fulfilling the 3D Abbe principle) while the metrology frame (also made from SiC) is stiff with no internal degree of freedom, avoiding the need for extra bearings.
The base frame consists of two granite guiding units - one for the X-Y system and one for the Z - joined to form a stable base frame. The air bearing-equipped direct drives for all three directions are each mounted separately from the part they drive.
ISARA 400 is fully equipped for ultra precision performance and user convenience. Thermal shielding prevents measurement errors because of differences in thermal expansion. Three vibration isolators counter disturbances due to environmental vibrations while automated product handling prevents damage to critical parts that could be caused by manual operations. The machine comes with a separate Abbe probe alignment tool and a camera for measurement visualisation - especially useful during product alignment - in addition to dust protection and acoustic insulation.
IBS PE's Triskelion ultra-precision touch probe will be initially implemented in the ISARA 400. Its design addresses the problems associated with most conventional probe systems: measuring uncertainty, probing forces and probe tip being too large. An AFM, a non-contact probe or optical probe, can also be implemented in the machine.
For all axes, the 1D measuring uncertainty is 45 nm, whereas the full-stroke 3D measuring uncertainty totals 100 nm. ISARA 400 can be used, for example, to measure large, free-form optic components. The large measuring volume, in conjunction with the automated product handler, allows the use of trays containing several products to be measured in one run. The ISARA 400 will be available by the end of 2009.
About IBS Precision Engineering
Since 1993, IBS Precision Engineering has been providing high-precision measuring solutions to high-tech customers by developing and building special machines, non-contact precision sensors, porous media air bearings and machine tool calibration and inspection systems. IBS PE is an expert in high-precision metrology, delivering ultra-precision measuring machines to researchers and high-tech industries, including semiconductor, aerospace and optics manufacturing. IBS PE's head office is in Eindhoven, the Netherlands; additional offices are located in Stuttgart, Germany and Evry, France.
For further information, please contact sales manager Hans Ott at IBS Precision Engineering, tel: +31 (0) 40 290 1270; info@ibspe.com; or visit www.ibspe.com
Contacts:
Sales:
Hans Ott Sales Manager
INTL
Phone: +31 (0) 40 290 1270 E-mail this person Company Information: Name: IBS Precision Engineering Address: Industrieterrein Esp Esp 201 City: Eindhoven Country: Netherlands Phone: http://www.ibspe.com
News provided by ThomasNet News® (TNN). TNN is a comprehensive source
of new and timely product information in the industrial marketplace. TNN supplies new product
information to the web sites, e-marketplaces and print publications that serve the
industrial marketplace. For press release submissions please go to
http://news.thomasnet.com/submitpr.html.
BY ACCESSING, BROWSING AND/OR USING THIS WEB SITE AND/OR ANY WEB SITES PROVIDED BY
ProductNews.com, YOU AGREE TO BE BOUND BY THE TERMS OF USE
AGREEMENT.
del.icio.us
DIGG
Facebook
Reddit
StumbleUpon
Twitter
![[Get Copyright Permissions]](http://license.icopyright.net/images/icopy-w.gif){kind=small}
