Non-Contact Measurement System uses concentrated light.
May 22, 2008 -
Able to measure radii down to 0.004 in., MAXOS system measures actual surface material without need to spray it with matt coating. Accuracy of system is ±0.0004 in. on polished and machined services and resolution between measured points is down to 0.0001 in. Suited for turbine blade manufacturers, system's use of non-contact measurement helps ensure that CFD simulations precisely match physical tests used to validate simulations.
(May 16, 2008) - NVision's non-contact measurement services are helping several major manufacturers of turbine blades improve blade performance by increasing the accuracy of flow simulations used in the design process. In the past, the blade manufacturers could not accurately measure prototype blades, especially the leading and trailing edges. Therefore they could not be sure that physical tests matched simulations, making it very difficult to validate the test results. NVision uses its MAXOS system to measure the critical blade geometry ensuring the prototypes blades meet the design intent and enhance simulation accuracy.
Today's most advanced turbine blades used in power generation are primarily designed by using computational fluid dynamics (CFD) to simulate the flow of gases over the blades. Simulation gives engineers the ability to quickly and inexpensively evaluate the performance of many different blade designs using virtual prototypes. However, before a CFD model can be used with confidence to evaluate blade geometry it must be validated by running a physical test with an identical blade and operating conditions to make sure the simulation matches the test results.
The problem with new generation turbine blades is their complexity has made it impossible to fully capture the critical geometry with standard coordinate measuring machines (CMMs), laser scanners or white light scanners. CMMs only capture one point at a time and their touch probes are too large to measure very small fillet radii. Additionally, ball-offset geometry limits the ability to accurately measure leading and trailing edges. Another problem with conventional CMMs is three axes of motion is often not enough to access the entire blade geometry, including the root. Laser and white light scanners capture a large amount of data, but once again struggle to accurately define the leading and trailing edges. Another issue with laser and white light is the inability to measure machined or polished surfaces without first coating them with a matt spray that varies in thickness between 1 and 5 thousands of an inch and compromises the accuracy of the measured points to the same, unacceptable degree.
The turbine blade manufacturers have addressed this problem by working with NVision's contract service division in Wixom, Michigan, which has a long history of working with turbine OEMs and their suppliers. NVision uses the MAXOS system, which measures using a concentrated light rather than a touch probe. The system eliminates the inaccuracies inherent in contact probe measurement on small radii or sharp edges, caused by ball-offset geometry, sometimes known as "the cosine error". In fact, the MAXOS can measure radii down to 0.004". Unlike other non-contact measurement systems, the MAXOS measures actual surface material without the need to spray it with a matt coating. The accuracy of the system is +/- 0.0004" on polished and machined services and the resolution between the measured points down to 0.0001".
With NVision now measuring the critical blade geometry to high levels of accuracy, the blade designers can squeeze the last bit of performance out of their blades. Current blades in production can also benefit from more accurate measurements.
NVision's non-contact measurement helps ensure that CFD simulations precisely match the physical tests used to validate the simulations. The end result is that the turbine blade manufacturers can optimize their blades to higher levels of performance and reduce the cost of expensive physical testing.
o28287 Beck Rd., Suite 3D, Wixom, MI 48393. Ph: 248.468.2525 or 248.756.2627, Fax: 248.468.2528.
E-mail: sales@nvision3d.com. Visit NVision's Web site at www.nvision3d.com. Company Information: Name: NVision, Inc. Address: 112 Welford Lane, Suite 126 City: Southlake State: TX ZIP: 76092 Country: USA Phone: 817-749-0050 FAX: 817-749-0053 http://www.nvision3d.com
News provided by ThomasNet Industrial Newsroom® (TIN). TIN is a comprehensive source
of new and timely product information in the industrial marketplace. TIN supplies new product
information to the web sites, e-marketplaces and print publications that serve the
industrial marketplace. For press release submissions please go to
http://www.productnews.com/SubmitPRPage.html.
BY ACCESSING, BROWSING AND/OR USING THIS WEB SITE AND/OR ANY WEB SITES PROVIDED BY
ProductNews.com, YOU AGREE TO BE BOUND BY THE TERMS OF USE
AGREEMENT.
![[Get Copyright Permissions]](http://license.icopyright.net/images/icopy-w.gif){kind=small}
