Software Radio PMC suits signal-intelligence applications.
May 8, 2008 -
Attached to PMC carrier board, Model 7151 provides four 200 MHz 16-bit A/D converters that feed FPGA IP core, which delivers 256 channels of digital down conversion. Unit enables independent frequency tuning for each down converter channel, and can down-convert any signal within any of 4 digitized 100 MHz input bands. Arranged in 4 banks of 64 DDC channels, each bank can be configured for unique output signal bandwidth to accommodate mixed signal applications or multiple modulation schemes.
Pentek Delivers Highest-Density Software Radio PMC with 256 DDC Channels and Four 200 MHz 16-bit A/Ds
o Complete software radio system solution in a single module
o Four RF/IF inputs digitized at 200 MSPS with 16-bit resolution
o 256 DDC channels independently tunable across four 100 MHz bands
o Highly optimized Virtex-5 FPGA technology
o Flexible assignment of A/Ds to DDC channels
o Extremely low cost per DDC channel
SCOTTSDALE, AZ, Critical Embedded Systems-May 5, 2008-Pentek, Inc., with its proven track record as a pioneer in software radio innovation, today introduced its Model 7151 high-performance, high-resolution software radio module. Four 200 MHz 16-bit A/D converters feed a proprietary FPGA IP core that delivers 256 channels of digital down conversion. Particularly well suited for GSM cell-phone monitoring and signal-intelligence applications, the Model 7151 leads the industry with the best resolution and highest channel density in the market today.
With independent frequency tuning for each of the 256 digital down converters (DDC) channels, the Model 7151 can down-convert any signal within any of the four digitized 100 MHz input bands, significantly enhancing the efficiency and diversity of signal-intelligence applications. Arranged in four banks of 64 DDC channels, each bank can be configured for a unique output signal bandwidth to accommodate applications requiring mixed signal types or multiple modulation schemes. Each DDC bank can be independently sourced from any one of the four A/D converters, which are typically assigned to specific antennas. As a result, the Model 7151 affords the engineer extreme flexibility for simultaneously capturing hundreds of signals spanning a wide range of modulation types, signal bandwidths and antenna sources.
"With its highly optimized 256 channel DDC IP core engine, the Model 7151 represents an entire software radio front end, boasting a channel density eight times higher than any other competing product in the marketplace. The Model 7151 is fully supported with drivers and it comes ready to use with the FPGA code already developed and installed. Not only does the 7151 module reduce development time and risks, it also saves designers space, power and costs in their software radio systems," says Rodger Hosking, vice president, Pentek.
"Plus, the flexible decimation settings, input selections and tuning options, all unique to the Model 7151, provide engineers with unprecedented choices to suit specific applications," Hosking added.
A Very Fast Front End
The front end accepts four +10 dBm, full-scale analog RF or IF inputs on front-panel SMC connectors into 50 ohms, with transformer couplings to four 200 MHz, 16-bit A/D converters. The digitized outputs are delivered into a Xilinx Virtex-5 FPGA for routing, formatting and DDC signal-processing operations. The 200 MHz A/Ds accommodate input signal bandwidths of up to 100 MHz, representing a 37% increase over previous Pentek modules.
256 Channel Digital Down Converter
The Model 7151 employs an advanced FPGA-based DDC engine comprised of four identical 64-channel DDC banks. Four independently controllable input multiplexers select one of the four A/Ds as the input source for each DDC bank. In this way, many different configurations can be achieved, including one A/D driving all 256 DDC channels and each of the four A/Ds driving its own DDC bank. Each of the 256 DDCs has an independent 31-bit tuning frequency setting that ranges from DC to fs/2, where fs is the A/D sampling rate.
Decimation and Filtering
All of the 64 channels within a bank share a common decimation setting that can range from 128 to 1024, programmable in steps of 64. For example, with a sampling rate of 200 MHz, the available output bandwidths range from 156 kHz to 1.25 MHz.
Each 64-channel bank can have its own unique decimation setting supporting as many as four different output bandwidths on the board. This flexibility allows customers map the DDC to their own particular application.
The decimating filter for each DDC bank accepts a unique set of user-supplied 18-bit coefficients. The 80% default filters deliver an output bandwidth of 0.8*fs/N, where N is the decimation setting. The rejection of adjacent-band components within the 80% output bandwidth is better than 100 dB. Each DDC delivers a complex output stream consisting of 24-bit I and 24-bit Q samples at a rate of fs/N.
Any number of channels can be enabled with each bank, selectable from 0 to 64. Each bank includes an output sample interleaver that delivers a channel-multiplexed stream for all enabled channels within the bank.
Output Multiplexers and FIFOs
Four output MUXs can be independently switched to deliver either A/D data or DDC data into each of the four output FIFOs. This allows users to view either the wideband A/D data or the narrowband DDC data, depending on the application. Each of the output FIFOs
operates at its own input rate and output rate to support different DDC decimation settings between the banks and efficient block transfers to the PCI bus.
A Variety of Form Factors and Configurations
The 7151 PMC module can be attached to any PMC carrier board. The Model 7651 is a PCI-board version, and it can readily be plugged into a desktop PC.
For CompactPCI systems, the 7251 is a 6U module and the 7351 is a 3U module. Pentek will soon be announcing PCI Express versions of the module as well.
What's more, a 4207 processor board with its two mezzanine sites can support two 7151 PMCs delivering 512 DDC channels in a single VME slot - an extraordinarily powerful single-slot solution. Software and software-support packages are available for Linux, Windows and VxWorks operating systems.
Pricing and Availability
For pricing and availability, please contact Mario Schiavone at 201-818-5900.
About Pentek
Pentek develops, manufactures and markets innovative DSP systems to original equipment manufacturers, distributors and value-added resellers. Pentek offers powerful VME, VXS, PMC, XMC, cPCI and PCI boards for data acquisition, software radio and digital signal processing featuring Texas Instruments C6000 DSPs, Freescale G4 PowerPCs and Xilinx FPGAs. Pentek's I/O includes A/Ds, D/As, FPGAs, digital up/downconverters and more. Pentek equips all products with high-performance I/O including Gigabit serial interfaces and offers strong DSP software support.
Pentek and VxWorks are registered trademarks of Pentek, Inc. Brand or product names are registered trademarks or trademarks of their respective holders.
For the release, photograph and data sheet, please visit:
http://www.pentek.com/whatsnew/ViewRelease.cfm?Index=106
North American Sales Contact: Mario Schiavone, Pentek, Inc., One Park Way, Upper Saddle River, NJ 07458-2311; Telephone 201-818-5900, ext. 770; Fax 201-818-5904; Email news@pentek.com. Website www.pentek.com.
International Sales Contacts: Elexo in France 0141 22 1023, VSystems Electronic GmbH in Germany at 892737630, VSystems s.r.l. in Italy at 119661319, VSystems AB in Sweden at 84441557, VSystems UK at 1494476000, Sela Electronic Systems in Israel at 36479969, MISH International in Japan at 425387650, Beijing BetaOne Sysjob Ltd. in China at 1082784106 and Acetronix Co. Ltd. in Korea at 24202343, ext. 106. Please visit http://www.pentek.com/contact/replist.pdf for a full list of international Pentek representatives and distributors.
Contacts:
Sales:
Mario Schiavone
USA
Phone: 201-818-5900 ext 770
FAX: 201-818-5904 E-mail this person Company Information: Name: Pentek Inc. Address: 1 Park Way City: Upper Saddle River State: NJ ZIP: 07458 Country: USA Phone: 201-818-5900 FAX: 201-818-5904 http://www.pentek.com
News provided by ThomasNet Industrial Newsroom® (TIN). TIN is a comprehensive source
of new and timely product information in the industrial marketplace. TIN supplies new product
information to the web sites, e-marketplaces and print publications that serve the
industrial marketplace. For press release submissions please go to
http://www.productnews.com/SubmitPRPage.html.
BY ACCESSING, BROWSING AND/OR USING THIS WEB SITE AND/OR ANY WEB SITES PROVIDED BY
ProductNews.com, YOU AGREE TO BE BOUND BY THE TERMS OF USE
AGREEMENT.
![[Get Copyright Permissions]](http://license.icopyright.net/images/icopy-w.gif){kind=small}
