November 14, 2007 -
Offering software radio system in COTS PMC/XMC module, Model 7142-428 employs 4 A/D converters and 1 D/A converter capable of bandwidths exceeding 40 MHz for connection to HF and IF ports of communications or radar systems. Digital downconverters in IP core are implemented as 2 cascaded DDC stages, each with programmable decimation of 1-256. Because decimations from 2 stages multiply, users can choose decimation from 2-65,536. Interpolation filter extends interpolation range to x2-x32768.
Pentek's New Digital Transceiver with Multiband DDC Core and Interpolation Filter Supports all Communication Bandwidths
o Complete Software Radio System
o Unique Quad DDC IP Core Combines Narrowband and Wideband Functions
o Input and Output Signal Bandwidths from 8 kHz to 40 MHz
o Decimation Range from 2 to 65,536 and Interpolation Range from 2 to 32,768
DENVER, CO, SDR Technical & Product Exposition-November 6, 2007-Pentek, Inc., a pioneer in VME board-level technology, today released its Model 7142-428 Digital Transceiver with a Multiband Digital Downconverter (DDC) and Interpolation Filter. A complete software radio system in a COTS PMC/XMC module, this latest offering from Pentek combines proven hardware and a new GateFlow IP core. It is a complete software radio system in a COTS PMC/XMC module. It employs four A/D converters and one D/A converter capable of bandwidths exceeding 40 MHz for connection to HF and IF ports of communications or radar systems.
In a transceiver, the decimation factor and interpolation factor determine the ratio between the IF frequency and the bandwidth of the received and transmitted signals. By offering a range of more than four orders of magnitude for both decimation and interpolation, the Model 7142-428 addresses an unprecedented range of commercial and military communication systems.
These include voice-band systems with 8-kHz channels, through 1G, 2G and 3G wireless waveforms, and even the new emerging 4G standards with bandwidths to 20 MHz and higher. Worldwide markets for wireless Web access for both fixed and mobile digital services are fueling numerous wireless standards, each with unique signal requirements easily handled with this new product. The highly programmable bandwidths offered in the Model 7142-428 also make it ideally suited for military software defined radio systems that require flexible hardware capable of emulating multiple radio waveforms.
"To summarize, we've taken a proven Pentek product, our Model 7142, and increased its performance to accommodate the growing number of communications standards our customers are looking for," says Rodger Hosking, vice president, Pentek. "The decimation and interpolation ranges in our Model 7142-428 cover virtually every requirement we've seen so far. Furthermore, this versatile new product can support systems being developed for new wideband radar and communication standards," he added.
"Because the Model 7142-428 incorporates highly optimized, world-class FPGA IP cores fully supported with software drivers, our customers can eliminate FPGA development risks, and get their systems to market on time," concludes Hosking.
Downconverting
Commercial DDC ASIC offerings are divided into two classes by their decimation range: above 32 for narrowband devices and below 32 for wideband DDCs. This limitation often forces customers to choose between DDCs or to use two devices to handle both classes.
Instead, each of the four DDCs in the 428 IP core is implemented as two cascaded DDC stages, each with a programmable decimation of 1 to 256. Because the decimations from the two stages multiply, users can choose an overall decimation anywhere from 2 to 65,536. As a result, each of these "multi-band" DDC cores spans the decimation range of both wideband and narrowband DDCs, all in a single device.
The four down-converted DDC outputs are delivered to the PCI interface through independent FIFOs, each managed by its own DMA controller channel to simplify programming and improve data transfer rates.
Four 14-bit A/D converters at the front end operate at sample rates up to 125 MHz. Each of the four identical DDC engines uses an independent 4-input multiplexer to select any one of these four A/Ds as its input source. The four DDCs feature independent tuning and decimation to translate any frequency band at the input down to zero frequency.
Upconverting
On the upconverting side, a Texas Instruments DAC5686 offers a 500-MHz 16-bit D/A converter and a digital upconverter (DUC) operating at a sample rate of up to 320 MHz. The DUC has a built-in interpolation range of only x2 to x16. The 428's IP core interpolation filter dramatically extends this rather limited range of interpolation by an additional factor of x2 to x2048, providing an overall range of x2 to x32768.
This extended DUC interpolation range nicely matches the DDC decimation capabilities of 2 to 65,536, offering symmetrical support for transmit and receive functions for signals of any given bandwidth. After interpolation, the DUC can be tuned to translate the baseband transmit signal frequency to any IF output frequency up to 140 MHz.
Software Support
All of the new 428 IP core functions are fully supported by Pentek's ReadyFlow Board Support Packages IBSP). Pentek's ReadyFlow BSPs simplify board operation and setup with easy-to-use function calls. ReadyFlow libraries offer flexibility and provide low-level access to all of the board's hardware. Pentek ReadyFlow BSPs and software development tools --plus third-party offerings -- are all available for a variety of operating systems including Windows 2000/XP, Linux and VxWorks platforms.
All of these software resources enable full control of all new features of the GateFlow 428 core, including configuration of the data flow into and out of the new IP core and full access to operating parameters including interpolation and decimation factors, DDC and DUC source selection, DDC tuning frequencies, filter coefficients, data formatting and modes of operation.
Pricing and Availability
The Model 7142-428 PMC/XMC is priced at $15,500 USD, with delivery 8 to10 weeks ARO. Support for Windows operating systems is immediately available. Linux and VxWorks support will follow.
About Pentek
Pentek develops, manufactures and markets innovative DSP systems to original equipment manufacturers, distributors and value-added resellers. Pentek offers powerful VME, VXS, PMC, XMC, cPCI and PCI boards for data acquisition, software radio and digital signal processing featuring Texas Instruments C6000 DSPs, Freescale G4 PowerPCs and Xilinx FPGAs. Pentek's I/O includes A/Ds, D/As, FPGAs, digital up/downconverters and more. Pentek equips all products with high-performance I/O including gigabit serial interfaces and offers strong DSP software support.
Pentek, ReadyFlow and GateFlow are registered trademarks of Pentek, Inc. Brand or product names are registered trademarks or trademarks of their respective holders.
North American Sales Contact: Mario Schiavone, Pentek, Inc., One Park Way, Upper Saddle River, NJ 07458-2311; Telephone 201-818-5900, ext. 770; Fax 201-818-5904; Email news@pentek.com. Website www.pentek.com.
International Sales Contacts: Elexo in France 0141 22 1000, VSystems Electronic GmbH in Germany at 892737630, VSystems s.r.l. in Italy at 119661319, VSystems AB in Sweden at 84441550, VSystems UK at 1494476000, Sela Electronic Systems in Israel at 36479969 and MISH International in Japan at 425387650, Beijing BetaOne Sysjob Ltd. in China at 1082784106 and Acetronix Co. Ltd. in Korea at 24202343. Please visit http://www.pentek.com/contact/replist.pdf for a full list of international Pentek representatives and distributors. Company Information: Name: Pentek Inc. Address: 1 Park Way City: Upper Saddle River State: NJ ZIP: 07458 Country: USA Phone: 201-818-5900 FAX: 201-818-5904 http://www.pentek.com
News provided by ThomasNet Industrial Newsroom® (TIN). TIN is a comprehensive source
of new and timely product information in the industrial marketplace. TIN supplies new product
information to the web sites, e-marketplaces and print publications that serve the
industrial marketplace. For press release submissions please go to
http://www.productnews.com/SubmitPRPage.html.
BY ACCESSING, BROWSING AND/OR USING THIS WEB SITE AND/OR ANY WEB SITES PROVIDED BY
ProductNews.com, YOU AGREE TO BE BOUND BY THE TERMS OF USE
AGREEMENT.
![[Get Copyright Permissions]](http://license.icopyright.net/images/icopy-w.gif){kind=small}
