Power Disconnect targets fluorescent lighting fixtures.
December 8, 2006 -
Sta-Kon® Luminaire Disconnect enables disconnection of power to fluorescent lighting fixtures without exposure to live wires. UL® listed and CSA certified, device consists of male and female disconnect body with pre-stripped wire connected to male and female tin-plated brass contacts, housed in crack-, abrasion-, and impact-resistant polycarbonate. Device includes 18 ga AWG solid copper-insulated wire leads, and latch to verify contacts are secured.
(Archive News Story - Products mentioned in this Archive News Story may or may not be available from the manufacturer.)
Thomas & Betts Introduces Device that Enables Safe Disconnection of Fluorescent Luminires
Sta-Kon® Luminaire Disconnect is the First to Respond to
New Industry Requirements
MEMPHIS, Tenn. - Dec. 5, 2006 - Thomas & Betts has introduced the Sta-Kon® Luminaire Disconnect, the first device to enable disconnection of power to fluorescent lighting fixtures without exposure to live wires. The Luminaire Disconnect was developed in response to a new National Electrical Code® requirement that will go into effect on Jan. 1, 2008. A similar industry requirement currently is in effect in the Canadian Electrical Code, Part I, Canada, 2006 Edition. The Luminaire Disconnect is the first to be UL® listed and CSA certified for this application. It complies with NEC® 410.73 (G), 2005 edition, and CEC part I, rule 30-308(4).
According to the International Brotherhood of Electrical Workers, "277-volt lighting circuits are the biggest killer [of electricians]." Connected between a fluorescent lighting fixture or ballast and incoming power, the Luminaire Disconnect is a cost-effective solution that enables the electrician to service the luminaire without exposure to dangerous voltage.
The Luminaire Disconnect consists of a male and female disconnect body with pre-stripped wire connected to the male and female contacts. The contacts, similar to Sta-Kon's male and female terminal disconnects, are made of tin-plated brass. The disconnect terminals are housed in crack-, abrasion- and impact-resistant polycarbonate.
Among the Luminaire Disconnect's features is a finger-safe female line side with wire connectors that prevent the installer from touching hot contacts, eliminating the need to disconnect power to service the fluorescent luminaire. The male side is connected to the fluorescent luminaire ballast - not to active power. Other features include No. 18 GA AWG solid copper-insulated integral wire leads that are compatible with multiple sizes of copper or aluminum wire to simplify installation, as well as an integral latch in the polycarbonate housing, providing a visible and audible verification that the contacts are secured and preventing nuisance outages by not disengaging under small amounts of tension on the wires. An additional benefit of the integral leads is the ability to provide a safe disconnect for a single luminaire that includes multiple ballasts - one disconnect removes the voltage from all the ballasts within the luminaire.
"Beginning in 2008, all new luminaires must be installed with a luminaire disconnect," said Dan Vega, product manager for Thomas & Betts. "When a servicing electrician replaces a fluorescent luminaire in a commercial building, for example, the
code will require the installation of a luminaire disconnect between the power line
and the ballast. Once the new disconnect is installed, the servicing electrician will be able to disconnect power to the ballast without handling live wires. Canada's requirements for luminaire disconnects already are in effect, but electrical inspectors haven't been able to enforce them, because a luminaire disconnect hasn't been available."
Additional features include Pok-A-Yok design that enables mating halves to be installed only one way, ensuring the correct electrical polarization; oversized electrical contacts, which improve conductivity and limit temperature increases; a bright orange color that is clearly visible and signifies a safety device; clear identification of the line and load on each polycarbonate housing; and a rounded, compact design that is easy to handle and small enough to be used in tight applications.
For more information about the Sta-Kon® Luminaire Disconnect, visit www.tnb.com or contact your Thomas & Betts sales representative by calling (800) 816-7809.
Corporate Overview
Thomas & Betts Corporation (NYSE: TNB) is a leading designer and manufacturer of electrical components used in industrial, commercial, communications and utility markets. The company is also a leading producer of commercial heating units and highly engineered steel structures used, among other things, for utility transmission. Headquartered in Memphis, Tenn., the company has manufacturing, distribution and office facilities worldwide. In 2005, the company reported sales of $1.7 billion.
Contacts:
Public Relations:
HB&M
Camille Dager
USA
Phone: 215-440-9800 Company Information: Name: Thomas & Betts Corp. Address: 8155 T&B Blvd. City: Memphis State: TN ZIP: 38125 Country: USA Phone: 800-888-0211 FAX: 901-252-1366 http://www.tnb.com
News provided by ThomasNet News® (TNN). TNN is a comprehensive source
of new and timely product information in the industrial marketplace. TNN supplies new product
information to the web sites, e-marketplaces and print publications that serve the
industrial marketplace. For press release submissions please go to
http://news.thomasnet.com/submitpr.html.
BY ACCESSING, BROWSING AND/OR USING THIS WEB SITE AND/OR ANY WEB SITES PROVIDED BY
ProductNews.com, YOU AGREE TO BE BOUND BY THE TERMS OF USE
AGREEMENT.
del.icio.us
DIGG
Facebook
Reddit
StumbleUpon
Twitter
![[Get Copyright Permissions]](http://license.icopyright.net/images/icopy-w.gif){kind=small}
