Archive News Story
(Products mentioned in this Archive News Story may or may not be available from the manufacturer.)
High Voltage Gate Driver ICs sense fault conditions.
June 22, 2005 - Rated at 1,200 V, 3-phase analog Model IR22381 features integrated de-saturation and 0.5 µsec deadtime. Models IR2277 and IR2271 are high-speed, single-phase current sense interface ICs with synchronous sampling for motor drive applications. Models IR2214 and IR22141 drive single half-bridge circuits in power switching applications as well as 3-phase 380 Vac circuits at up to 50 A at 80°C. For appliance motor drives and general-purpose inverter circuits, 1,200 V HVICs are available in 600 V versions.
Archive Press Release
(Products mentioned in this Archive Press Release may or may not be available from the manufacturer.)
Release date: June 1, 2005
International Rectifier Introduces Fast and Rugged 1200V and 600V High Voltage Gate Driver ICs with Sophisticated Functions and Reduces PCB Area Up to 50%
IR’s integrated HVIC technology enables sophisticated protection and shrinks size compared to opto-coupler- or transformer-based discrete solutions.
EL SEGUNDO, CA., June 2005 — International Rectifier, IR®(NYSE: IRF), a world leader in power management technology, today introduced a series of high voltage IGBT control ICs with a sophisticated set of protection functions. In addition to these advanced functions, these devices feature high noise immunity with up to 30% fewer components in half the footprint compared to discrete opto-coupler- or transformer-based solutions. The series consists of 1200V and 600V gate driver ICs and current sense interface ICs for a variety of applications including inverterized motor drives, general-purpose inverter circuits, switch-mode power supplies (SMPS) and uninterruptible power supplies (UPS).
“This new suite of gate driver and sensor ICs made with IR’s high voltage IC technology enables small circuits with full protection, including ground fault protection, which was once available only in high-end systems. The new ICs blaze a new path for low-end industrial or servo drives as well as cost-competitive appliances,” said David Tam, Vice President of IR’s Consumer and Industrial group.
Power stages using IGBTs or MOSFETs must be protected from failures such as short circuits, over-current conditions and ground faults. In addition to protection circuits, the fault conditions must be detected, or sensed, in order to enable the protection functions. IR’s new line of driver ICs and sensor ICs fill this requirement, while reducing component count and simplifying circuits.
1200V HVICs for Industrial Applications
There are five 1200V gate drivers made with IR’s HVIC technology.
The IR22381 is an analog, three-phase IGBT gate driver. With a deadtime of 0.5µsec (micro-seconds), the device is ten times faster than comparable opto-coupler-based drivers. Also, the IR22381 minimizes temperature drift and changes in performance over time.
An integrated de-saturation feature provides for all modes of over-current protection, including ground fault, shoot-through and short to supply rails protection. Soft shutdown is initiated in the event of an over-current condition followed by the turn-off of all six outputs. A shutdown input is included to enable custom shutdown functions. The IR22381 includes programmable deadtime, and the output drivers have separate turn-on/turn-off pins with a two-stage turn-on output to achieve the desired IGBT dv/dt switching level. Voltage feedback provides accurate measurements, and a bootstrap power supply eliminates an auxiliary power supply.
The IR2277 and IR22771 are high speed, single-phase current sense interface ICs with synchronous sampling for motor drive applications. The current is sensed through an external shunt resistor which converts the analog voltage into a time interval through a precise dual ramp system. The time interval is level-shifted and provides digital PWM output suitable for DSP and analog-to-digital interfaces without additional logic circuits. The maximum throughput is 40kSamples/second, suitable for up to 20kHz asymmetrical PWM modulation and maximum delay is less than 7.5usec @20kHz. A noise immune bi-directional level-shifting circuit is used to avoid false common mode dV/dt noise up to 50V/ns. The IR2277 provides both analog and PWM output, while the IR22771 provides PWM output.
The IR2214 and IR22141 are designed to drive single half-bridge circuits in power switching applications as well as three-phase 380VAC circuits at up to 50A@80°C. Unlike solutions using opto-couplers, the IR2214 and IR22141 gate drivers deliver stability during their lifetime and include parameter matching, such as propagation delay for high- and low-side channels as well as deadtime insertion. Their low quiescent current on the high-side enables economical and space-saving bootstrap supply topology. Fault feedback on IGBT de-saturation is included which automatically shuts down the IGBT when used in multi-phase configurations. Desaturation detection for both sides as well as an internal biasing resistor are included in the IR2214, while an active de-saturation diode bias is included in the IR22141. The IR2214 and IR22141 can be connected together via a dedicated pin to protect the drive system from phase-to-phase short circuits. Input and output pins are 3.3V CMOS-compatible to simplify microprocessor interfacing. Separate power and signal ground pins enable emitter shunt configurations to simplify low-side IGBT current sensing. These devices are housed in a SSOP-24 package.
600V HVICs for Appliance Applications
For appliance motor drives and a wide range of general-purpose inverter circuits, the 1200V HVICs are available in 600V versions. The IR21381 is an analog three-phase driver, similar to the IR22381. The IR2177 and IR21771 are 600V versions of the IR2277 and IR22771. Rounding out the set, the IR2114 and IR21141 are 600V versions of the IR2214 and IR22141.
Design Assistance
Data sheets for these new HVICs are available on the International Rectifier Web site. Additional design assistance is available:
• IRMD22381Q demo board for the IR22381 and IR21381, a complete AC and brushless motor driver used with a 30A power module
• IRMD2214SS evaluation board for IR2214, IR22141, IR2114, and IR21141
• IRCS2277S – reference design kit for IR2277 and IR2177
IR’s High Voltage Integrated Circuit (HVIC) Technology
IR’s proprietary HVIC technology is ideal for designing products to drive MOSFETs and IGBTs. Gate drive outputs are designed using a latch-immune CMOS circuit. The technology integrates a low-voltage driver with a high-voltage level shifter for high-side and low-side gate drivers in one monolithic IC.
1200V Gate Driver ICs Made with IR HVIC Technology
Part Number Package Notes
IR22381Q 64-Lead MQFP Three phase gate driver IC with advanced protection functions
IR2277S 16-Lead SOIC High voltage current sensing IC with PWM and analog output
IR22771S 16-Lead SOIC High voltage current sensing IC with PWM output
IR2214SS SSOP-24 Half bridge gate driver IC with advanced protection functions
IR22141SS SSOP-24 Gate driver IC with advanced protection functions
600V Gate Driver ICs Made with IR HVIC Technology
Part Number Package Notes
IR21381Q 64-Lead MQFP Three phase gate driver IC with advanced protection functions
IR2177S 16-Lead SOIC High voltage current sensing IC with PWM and analog output
IR21771S 16-Lead SOIC High voltage current sensing IC with PWM output
IR2114SS SSOP-24 Half bridge gate driver IC with advanced protection functions
IR21141SS SSOP-24 Gate driver IC with advanced protection functions
Availability and Pricing
The new motor drive and sensor ICs are available immediately. Pricing is as follows, each in 10,000-unit quantity:
1200V Gate Drivers
IR23381Q: US $12.05 each
1200V Current Sensing ICs
IR2277S, IR22771S (analog output): US $3.94
1200V Half Bridge Drivers
IR2214SS, IR22141SS: US $4.50 each
600V Gate Drivers
IR21381Q: US $10.50 each
600V Current Sensing ICs
IR2177S, IR21771S (analog output): US 2.56 each
600V Half Bridge Drivers
IR2114SS, IR21141SS: US $3.90 each
Prices are subject to change.
About International Rectifier
International Rectifier (NYSE:IRF) is a world leader in power management technology. IR’s analog and mixed signal ICs, advanced circuit devices, integrated power systems and components enable high performance computing and reduce energy waste from motors, the world’s single largest consumer of electricity. Leading manufacturers of computers, energy efficient appliances, lighting, automobiles, satellites, aircraft and defense systems rely on IR’s power management benchmarks to power their next generation products. For more information, go to www.irf.com.
IR® and HEXFET® are trademarks of International Rectifier Corporation. All other product names noted herein may be trademarks of their respective holders.
Contacts:
General Information:
Wayne Yoshida
USA
Phone: 310-252-7726 E-mail this person Company Information: Name: International Rectifier Corp. Address: 233 Kansas St. City: El Segundo State: CA ZIP: 90245 Country: USA Phone: 800-981-8699 FAX: 310-322-3332 http://www.irf.com
News provided by ThomasNet Industrial Newsroom® (TIN). TIN is a comprehensive source
of new and timely product information in the industrial marketplace. TIN supplies new product
information to the web sites, e-marketplaces and print publications that serve the
industrial marketplace. For press release submissions please go to
http://www.productnews.com/SubmitPRPage.html.
BY ACCESSING, BROWSING AND/OR USING THIS WEB SITE AND/OR ANY WEB SITES PROVIDED BY
ProductNews.com, YOU AGREE TO BE BOUND BY THE TERMS OF USE
AGREEMENT.
![[Get Copyright Permissions]](http://license.icopyright.net/images/icopy-w.gif){kind=small}
