Pneumatic Power Drive provides power for threading pipe.

Reed Manufacturing Co.    Erie, PA 16512
May 21, 2013 Equipped with 4 hp motor that turns at 28 rpm no load, Model 700APD delivers max torque of 400 lb-ft, providing power for threading pipe and conduit up to 2 in. in diameter. Since drive is pneumatic, it can be used in environments where electric shock or sparks from electric tools are hazardous. Included Safety Arm absorbs forces generated during threading and frees up operator to oil dies.

Tool Kit helps users smoothly install pipe joints.

Reed Manufacturing Co.    Erie, PA 16512
May 21, 2013 Suitable for plastic pipe specialists, fire protection, and plumbing contractors, TC2PPDEB1-2SK includes Reed Quick Release™ Tubing Cutter and 2 DEB deburr/chamfer tools for plastic pipe, all in plastic case. Tubing cutter produces square cut so pipe bottoms out in fitting for maximum strength, while deburr/chamfer tools allow even distribution of glue around fitting for optimal fit of glue joints. Kit works for Schedule 40 and 80 PVC, CPVC, and PE pipe. 

Pipe Cutters come in sizes for large and small diameters.

Reed Manufacturing Co.    Erie, PA 16512
Jan 10, 2013 Designed for manual cuts on 40–42 in. steel pipe, RC42S Rotary™ Cutter tightens via included wrench and requires 11.8 in. clearance. Pipe snaps off squarely once operator works RC42S manually around cut zone. For 2–4 in. steel, cast iron, or ductile iron pipe, LCRC4 Low Clearance Rotary™ Cutter features heavy-duty construction and requires 4 in. clearance around pipe to make cut. Proprietary cutter wheels are used in both models.

PE Scraper prepares pipe OD for electrofusion.

Reed Manufacturing Co.    Erie, PA 16512
Oct 19, 2012 Designed for pipes ranging from  2–6 in., PE Scraper removes dirt and oxidation from outside diameter in preparation for electrofusion process. Unit features spring-loaded blade that keeps consistent pressure on pipe to yield smooth, finished surface without skipping. Used on edge of pipe or anywhere along length, scraper requires 6 in. clearance for turning around pipe. 

Pneumatic Saw offers blade guides to stabilize cut.

Reed Manufacturing Co.    Erie, PA 16512
Aug 01, 2012 Available for Saw It® Pneumatic Saw, Blade Guides are available in 21 and 30 in. lengths. Units reach across pipe section being cut and stabilize blade so that it does not whip and vibrate, extending blade life, squaring cut, and helping to eliminate accidental blade breakage. Providing power and reciprocating motion to blades, Saw It(TM) is suitable for cutting plastic, steel, and stainless steel pipe.

Squeeze-Off Tool for polyethylene pipe is suited for utility contractors.

Reed Manufacturing Co.    Erie, PA 16512
Jun 13, 2012 Intended for ½-2 in. IPS and CTS pipe, PES2 IPS/CTS (No. 04303) PE Squeeze-Off tool is constructed with aluminum parts and castings and has sliding bar handles that facilitate work in tight places while increasing leverage for tightening. Stops cover common IPS and CTS pipe sizes in one stops set, while fine-pitched thread on feed screw allows for controlled squeeze with minimal effort. Also included, grease fittings at friction points lend to smooth operation and help extend tool life.

Squeeze-Off Tools feature variety of stops.

Reed Manufacturing Co.    Erie, PA 16512
Jun 21, 2011 Supporting nominal diameters of 3-6 in. and 3-8 in., respectively, Models PES6 and PES8 compress polyethylene plastic tube/pipe to stop flow of water or gas. When used properly, pipe will return to its original shape and normal flow rates. Manual version develops clamping force by operator physically turning handle on long screw, while hydraulic version uses pump and cylinder for clamping. Positive stops prevent damage to tube from over clamping.

Pneumatic Saws have multiple safety features.

Reed Manufacturing Co.    Erie, PA 16512
Dec 15, 2010 Saw It® models SAWITSD and SAWITD feature immediate shutdown when throttle is released and immediate start upon throttle squeeze. On SAWITSD, trigger lock prevents accidental activation if trigger is unintentionally bumped/pressed. These tools can cut plastic, steel, and stainless steel, with 6 in. min clearance beyond pipe to accommodate blade movement. Products cut up to 20 in. dia pipe with single setup or larger pipe with optional chain extensions and several clampings.

Electric Threading Machine includes self-oiler.

Reed Manufacturing Co.    Erie, PA 16512
Sep 28, 2010 Supplied with foot pedal, pipe cutter, reamer, and dies, ½ hp Model 5401TMSO centers and chucks pipe and conduit and rotates it while cutting, threading, and reaming operations are performed. Three-spoke handwheel with gear and rack system moves high clearance carriage and starts die onto pipe for threading. Using self-priming pump, oil system generously floods pipe with oil while threading. Nominal threading capacity is ¼-2 in. for bolts and 1/8-2 in. for pipes.

Pipe Groover supports powered and manual operation.

Reed Manufacturing Co.    Erie, PA 16512
Jun 28, 2010 Combo Roll Groover model RGCOMBO812 forms standard rolled grooves in 8-12 in. steel, stainless steel, and aluminum pipe with up to 0.188 in. wall thickness. Professional-grade, 2-in-1 service tool allows complete change in minutes from power machine operation to manual work. Compact and designed for portability, tool meets jobsite grooving requirements of mechanical piping system installations and is available with one wrench for power grooving and angled wrench for manual grooving.