Latest New Product News from AMETEK Drexelbrook
Non-Contact Level Meter targets solids applications.AMETEK Drexelbrook Horsham, PA 19044
Jul 22, 2014 With frequency modulated continuous wave radar technology, DR6300 Series provides distance, level, volume, and mass measurement of powders, granulates, and other solids. Non-contact, 2-wire, k-band meter offers choice of touchscreens, including tank illustration, bar graph, oscilloscope, signal, and reflectivity screen. Available with drop antenna or horn antenna, device has measuring range of 260 ft and will operate up to flange temperature of 290°F and pressures of 580 psig.
RF Point Level Switch features maintenance-free design.AMETEK Drexelbrook Horsham, PA 19044
Oct 28, 2013 Offering alternative to electromechanical level switches, Z-tron IV™ Point Level Switch features all electronic design with no components to jam, break, or wear out. Cote-Shield™ circuitry allows switch to ignore coatings and build-up on sensing element. Switch reacts only to actual high- or low-level conditions; dust or tunneling will not produce false signal. Featuring integral, one-piece design, switch is installed through single ¾ in. vessel opening.
Water Cut Monitor includes temperature compensation.AMETEK Drexelbrook Horsham, PA 19044
Oct 04, 2013 Accommodating temperatures up to 160°F, Universal IV CM delivers accurate water cut measurement in 0–1%, 0–5%, 0–10%, and 0–30% ranges with accuracy down to 0.03% water and resolution down to 0.0002% water. Perm-A-Seal sensing element installs directly into main process line, and Cote-Shield™ technology ignores coating buildup on probe. Equipped with built-in LCD and keypad, monitor can be configured for NPT or flanged mountings and can be installed in all common pipe diameters.
Water Cut Monitor incorporates temperature compensation.AMETEK Drexelbrook Horsham, PA 19044
Aug 14, 2013 Temperature compensated (TC) version of Universal IV™ CM offers accurate water cut measurement in 0%–1%, 0%–5%, 0%–10%, and 0%–30% water ranges. Accuracy reaches 0.03% water, while measurement resolution is 0.0002% water. Cote-Shield™ technology ignores coating buildup on probe and puts sensing area of instrument directly into process stream. Installed directly into main process line, Perm-A-Seal sensing element utilizes PEEK material and stainless steel sensing rod.
Water Cut Monitor measures fluid properties inside process line.AMETEK Drexelbrook Horsham, PA 19044
Nov 13, 2012 Universal IV CM monitor is accurate to 0.03% water with measurement resolution of 0.0002% water. It takes average of capacitive property of fluid over its entire length, and then onboard electronics compute relationship between capacitance change and water cut. Unit features Perm-A-Seal sensing element, installed directly into main process line, and built-in LCD and keypad. Configurable for NPT or flanged mountings, product also installs in all common pipe diameters.
Water Cut Monitor offers accuracy down to 0.03% water.AMETEK Drexelbrook Horsham, PA 19044
Nov 12, 2012 Equipped with built-in LCD and keypad, Universal IV™ CM Model provides measurement resolution down to 0.0002 % water. Unit features Cote-Shield™ technology, which ignores coating buildup on probe. Extending minimum of 15 in. into process line, sensing element takes average of capacitive property of fluid over its entire length. Probe handles pressures to 1,500 psi and temperatures to 450°F. Configurable for NPT or flanged mountings, Universal IV CM comes pre-calibrated to 1 of 11 pre-set ranges.
Level Transmitter offerse immunity from diverse factors.AMETEK Drexelbrook Horsham, PA 19044
Jul 03, 2012 Featuring worldwide approvals, Universal IV(TM) RF Admittance/Capacitance continuous level measurement transmitter is intrinsically safe, explosion proof, and flameproof. This 2-wire, 4-20 mA loop transmitter features digital HART protocol as well as Cote-Shield(TM) technology and is immune to interference from vapor, dust, foam, and tank obstructions. Along with pushbutton LCD for configuration and monitoring, product features stable, repeatable, and accurate measurement within 0.25% of range.
Point Level Switch offers SIL-certified overfill protection.AMETEK Drexelbrook Horsham, PA 19044
Feb 04, 2009 Safety IntelliPoint RF(TM) Switch, used in above-ground bulk storage tanks, meets American Petroleum Institute's 2350 Recommended Practice for overfill/spill protection. Specifically, it comes standard with SIL1 certification; SIL2 is optional, and SIL3 is possible with redundant switch. Integral software continuously monitors application for changes and maintains repeatable trip point on probe. Switch detects presence or absence of material without calibration, and MTTF is 110 years.
Cut Monitor measures percentage of water in oil.AMETEK Drexelbrook Horsham, PA 19044
Aug 07, 2006 CM-6 Cut Monitor features Perm-a-Seal sensing element installed directly into main process line, which extends minimum of 15 in. and takes average of fluid capacitive property over entire length. Factory-calibrated and 11 pre-set ranges (0-50% in Light Oil and 0-80% in Heavy Oil) are included. Cote-Shield(TM) enables instrument to ignore pre-determined length of sensor, allowing extension beyond nozzle mounting and pipe elbows for accurate measurement.
Transmitters provide radar-based level measurement.AMETEK Drexelbrook Horsham, PA 19044
May 27, 2005 Radar Series DR7000 and Time Domain Reflectometry Series DR7100 incorporate touch screen display with choice of tank illustration, bargraph, oscilloscope, signal, or reflectivity screen. Utilizing FMCW technology, Series DR7000 features 2 MHz bandwidth that allows units to determine true level in tank despite agitated surfaces and vessel obstructions. Series DR7100 uses electromagnetic wave guided by metallic rod or flexible cable to determine distance, level, and volume.
Tuning Fork Switch offers high and low level indication.AMETEK Drexelbrook Horsham, PA 19044
May 25, 2005 Series TF-100 provides no-calibration solution to point level measurement of clean liquids and is available with relay, current, or PNP outputs. Made of 316 stainless steel, sensor is offered in standard and sanitary versions. When material level reaches predetermined point on sensing element, it causes change in status in electronic unit, resulting in output that can operate alarms, annunciators, valves, or other controls or indicators.
Level Transmitter offers continuous, ultrasonic performance.AMETEK Drexelbrook Horsham, PA 19044
May 25, 2005 Accurate to 0.15%, USonicâ„¢ Series provides repeatable level measurement of liquids. CPVC construction suits Class I, Div 1 environments with Intrinsically Safe or Explosion Proof installation requirements. Able to handle temperatures from -40 to +158°F and process pressures to 50 psig, transmitter is capable of liquid level measurement to 30 ft with 2-wire, 4â€“20 mA, HART output signal and comes with integral display and keypad for local configuration.
Safety Switch suits SIL1, SIL2, and SIL3 installations.AMETEK Drexelbrook Horsham, PA 19044
Dec 14, 2004 IntelliPoint SXRNT Series RF Admittance Point Level Switch offers Auto-Calibration feature that detects presence or absence of material for maintenance-free operation. In-line unit measures liquids, solids, and slurry materials as well as interface between any insulating and conductive liquid. Included software monitors changes in composition, dielectric, or conductivity and maintains repeatable trip point on probe.
Wireless Interface eliminates cable/conduit runs.AMETEK Drexelbrook Horsham, PA 19044
Aug 03, 2004 Wireless Interface Solution provides wireless transmitter/receiver set suited for use in harsh environments and Class 1 Division 2 areas. Utilizing 902â€“928 MHz ISM band spread spectrum frequency hopping technology, product delivers license-free, interference-free link between remote devices and control room. Transmitters are available in ac and dc power versions, while receiver is offered in dc only and is suitable for DIN-Rail mounting.
Level Sensor self adjusts to media and environment.AMETEK Drexelbrook Horsham, PA 19044
May 23, 2003 Ultrasonic, loop-powered, 2-wire Uniscan provides 0.25% accuracy and .11 in. resolution. Four-digit LCD reads out in level and distance of flow rate. Unit is suitable for ranges up to 49 ft in liquids and 28 ft in solids. Intelliscan 4-wire, low voltage unit provides 0.25% accuracy and 0.04 in. resolution. Single instrument can be used to measure liquids, solids, granular, slurry, or open-channel flow, without changing transducer.
|Home | My ThomasNet News® | Industry Market Trends® | Submit Release | Advertise | Contact News | About Us|
Brought to you by Thomasnet.com
Browse ThomasNet Directory|