Latest New Product News from
Bud Industries, Inc.
Made of die-cast aluminum and sealed with continuous silicon rubber gasket, ATX Series is rated for such explosive atmospheres as grain dust and conductive dust (Zones 21, 22) and certified to ATEX II 2 G Ex e IIC Gb and ATEX II 2 D Ex tb IIIC Db. Aluminum body is powder coated, and captive screws in cover are stainless steel. Rated for -50 to +135°C, enclosures come in 10 sizes from 2.95 x 3.15 x 2.24 in. to 14.17 x 6.30 x 3.54 in. and are UL listed and rated at IP66 per IEC 60529 standard. Read More
Made of anodized aluminum extrusion with grooves for heat dissipation, EXN Series is available with polycarbonate plastic or powder-coated die-cast aluminum endcap covers that can be removed to slide in printed circuit board. Exterior has built-in 0.5 mm recessed area on which product label can be affixed and/or printed on directly. Available in 17 sizes ranging from 2.7 x 1.39 x 1.93 in. to 6.99 x 2.41 x 8.23 in., enclosures include continuous gaskets that seal against weather and water. Read More
Used independently or mounted on 35 mm DIN rail, IP66-rated DMX Series is made of extruded aluminum and features polycarbonate plastic endcaps. Latter have UL94-V0 flammability rating and are sealed with EPDM gasket. Integrated slots allow for mounting up to 3 PCBs, which are offered as optional accessories, and available modifications include holes, slots, or cutouts. There are 6 sizes available from 2.72 x 3.87 x 0.28 in. and 3.87 x 1.1 x 2.72 in. to 3.87 x 6.56 x 2.72 in. Read More
Suited for outdoor use, IPV Series PC/PC Wide Opening External Vent allows circulation of air while protecting againt rain water and falling debris. Both 2.91 x 2.91 x 1.1 in. and 3.95 x 3.95 x 1.25 in. models, constructed of gray polycarbonate plastic and 10% fiberglass, withstand exposure to UV light and water in accordance with UL 746C. Also able to be used indoors, product features continuous gasket between enclosure and vent and is designed to provide IP32 protection.
Offering corrosion resistance in washdown, humid, and outdoor environments, PBB Push Button Box carries NEMA 4X/IP67 rating and meets requirements of UL 746C with respect to UV light and water exposure. Construction combines polycarbonate plastic and 10% fiberglass for combined shatter resistance and molding consistency. Latter results in tight tolerances and seal reliability. Gray PBB Push Button Box suits 22 and 30 mm push buttons and comes in sizes from 0.89 x 1 in. to 1.22 x 4 in. Read More
Rated to NEMA 1/2/4/4x and IP67, PIP Series seals out water and dust to protect electronics. Enclosure is made from polycarbonate plastic enhanced with 10% fiberglass, and design ensures precise component fit without rework. Box cover is polycarbonate, and clear polycarbonate lid is available to facilitate and accelerate inspection. Offered in sizes from 3.15 x 1.18 x 1.37 in. to 10.04 x 4.92 x 0.25 in., enclosure is chemical resistant and uses captive, non-metallic screws to secure cover. Read More
Featuring clamshell design that fits together with tongue and groove seal, Bud Tablet Enclosures provide protection for electronics used in industrial automation and control as well as other mission-critical applications that might involve harsh environmental conditions. Sizes range from 5.5 x 3.9 x 1.2 in. to 12.7 x 9.1 x 1.2 in., and high-impact ABS plastic construction is flame retardant to UL94-VO (white) and UL94-HB (black). Recessed area is provided for touchscreen or LCD screen. Read More
Using flat or folded approach, Board-ganizer keeps components of design project in one place, and facilitates storage and transport of breadboarded designs. PC development boards attach to enclosure using adhesive rubber feet. Up to 3 development boards and 1 breadboard may be installed on single enclosure. With hinged design, Board-ganizer lets users work on project with boards located side-by-side and later fold project into 5 x 5 x 3 in. enclosure with no need to disconnect wires. Read More
Made of high-impact ABS plastic that is flame retardant to UL94-VO (white) and UL94-HB (black), tablet enclosures for portable, desktop, or wall-mounted electronic applications come in sizes from 5.5 x 3.9 x 1.2 in. to 12.7 x 9.1 x 1.2 in. Tongue and groove sealing design protects against dust and moisture, and optional silicone sponge gasket imparts IP65 rating. Recessed area is designed for touchscreen or LCD. Read More
Measuring 3.62 x 2.60 x 1.10 in., FBB-3665 Enclosure is designed for KL25Z Freescale Freedom Development Platform. Board slips into place, secured in enclosure by snug fit rather than by potentially damaging hardware. Cutouts in front panel allow for connection to board's 2 USB ports and provide access to reset button, while round knockout plugs in rear accommodate optional miniature cable gland. Slot on each side of enclosure accommodates flat cables from I/O header banks. Read More
While upper compartment of DCH Series has transparent, screw-on or hinged cover that lets users view meters and other indicators as well as access system components that may require maintenance, lower compartment is designed to protect delicate components and contain electrical components that could pose touch hazard as well as other components not requiring frequent access. ABS plastic enclosures include 5 models with size from 6.34 x 6.54 x 3.66 in. to 11.06 x 11.65 x 6.22 in. Read More
Measuring 35 mm wide x 7.5 mm high x 1 m long, DIN Rails are made from 1 mm thick zinc-plated steel with 18 x 6.3 mm oblong slots spaced at 25 mm center to center for flexibility in mounting. Rails are suitable for mounting Bud DB, DPB, DMB, and TS-16 series enclosures and accessories. DIN rail mounting clips are also available. Read More
Compliant with NEMA and UL-50 Type 3R rating, NEMA box provides protection against rain, sleet, and damage from formation of external ice. Enclosure is constructed of heavy-duty 16 GA galvanized steel that provides corrosion protection and is coated with ASA-70 gray powder. While internal zinc-plated steel panel facilitates component mounting, external mounting brackets allow installation on vertical surfaces without opening cover and exposing internal components. Read More
Constructed of 16-gauge steel with flanged front lip that keeps equipment securely in place, SA Series fits open racks with 19 and 23 in. wide panel spaces and 5.25 in. of panel height. Units are 15 in. deep and can be mounted facing forward or backward in relay rack. Available in both ventilated and non-ventilated configurations, shelves may be requested in black texture or metallic gray powder coat finish. Read More
Offering open construction and removable door to aid hardware upgrades and maintenance, Swing Frame Rack combines wall-mounted rack functionality with swing-out frame. Product can be hinged left or right and provides storage for networking equipment. With 75 lb load capacity, each unit accepts No. 12-24 panel mounting hardware and mounts on 16 in. hole centers in back for stability. Frames come in 21 and 35 in. panel space heights and mount to 18 in. depth. Read More
Constructed from 14 GA steel with ANSI 61 grey powder coating, SPB Series meets NEMA 12/13 specifications. Cover has die-cut gasket for protection against dust, water, and oil. Cover screws thread into sealed nuts for additional sealing protection. Available in 4 sizes to accommodate either 22.5 or 30.5 mm push buttons, box can be mounted to wall or machine, providing protection for emergency shut-off controls in factory automation systems. Read More
Carrying NEMA 4 rating, PN-Series is offered in various plastic materials and with clear or solid cover. Molded-in external mounting brackets on back allow mounting on wall, panel, or machine, while cover-attaching screws outside sealing area provide additional shielding from moisture and dust. Most models have internal guide slots for mounting PCB assemblies vertically, and internal bosses allow for mounting of PCBs horizontally or for connection of terminals into threaded brass inserts. Read More
Available with 4 casters, portable BudRack Professional Series features ventilated tempered glass front door, solid steel locking rear door, and removable locking sides for security and quick access. It handles 19 in. rack-mount component equipment such as computer servers, monitors, KVMs, networking, and test instruments. Rack has 2 pairs of fully-adjustable 14 ga panel mounting rails, and comes complete with either two 23 in. or four 31 in. depth fans to expel air from cabinet. Read More
Featuring snap-fit design, DIN-rail-mount terminal block enclosure houses PCBs and terminal blocks used in industrial controls, relays, and test equipment. Unit is designed for modularity, so functions and features can be varied by substituting secondary circuit boards. Sizes from 1.43 x 3.55 x 2.55 in. to 6.28 x 3.55 x 2.26 in. are available, and product accommodates 12-54 terminals. Enclosure is manufactured with UL94V-0 rated ABS/PC blend plastic. Read More
Featuring double-channel sealing system that results in IP67 protection, die cast ANS Series uses continuous EMI/RFI gasket around entire perimeter of box and second gasket, made of one-piece silicone, that seals out dust and moisture. Screws outside sealing area ensure uniformly tight seal, while manufacture from No. ADC-12 aluminum using 0.098 in. thick wall construction provides strength and rigidity. Available sizes (18) range from 2.83 x 2.64 x 1.53 in. to 9.45 x 6.30 x 3.35 in. Read More
Other Company News from
Bud Industries, Inc.