Pepperl + Fuchs, Inc.
Twinsburg, OH 44087
Stationary Barcode Imager reads common 1D and 2D codes.
Rated to IP65 and usable over 32 to 122Ã-
Read More »
Remote I/O Gateway accelerates data transfer via Modbus TCP.
Comprised of Ethernet communication gateway and backplane, ETHERNET Remote I/O bridges field instruments and Modbus TCP-based Ethernet with data transfer rates to 100 Mbps. Field signals can have intrinsically safe connection for Div 1/Zone 0 applications, and up to 80 analog or 184 discrete signals can be controlled through one gateway. While high transfer frequencies require LWL connections for...
Read More »
Fieldbus-Based Power Supply suits explosive hazardous locations.
Dynamic Arc Recognition and Termination System (DART) is power supply and control system for fieldbus installations in intrinsic safety environments. Feeding power of 8-50 W, product detects change in current resulting from electrical fault where explosive spark is possible and immediately switches off power. Power is shut off in microseconds, robbing spark of energy needed to ignite hazardous...
Read More »
Stack Light Lamps offer alternative to stack light LEDs.
Intended for application where LED-lit stack lights are too costly to warrant use, VAZ-LAMP series stack lights provide visual Warning or Ready status indication. Products, available in blue, green, clear, yellow, and red, are lit by incandescent light bulb. If bulb burns out, it can be replaced without having to replace entire stack light. Stack lights are compatible up to 4 lights high with...
Read More »
AS-Interface Gateways support standard and safety networks.
Available in single master, dual master, and dual master with safety monitor versions, ENX Series supports Modbus/TCP and Ethernet/IP protocols for seamless communication with standard and safety networks. All models include integrated duplicate address, noise, and ground fault detection. With ENX gateways, 992 I/O are handled asynchronous to Ethernet traffic. Units scan every AS-i node in 150...
Read More »
Pepperl+Fuchs Industrial Flat Panel Monitors Now Zone 2 Certified for Use in Hazardous Environments
High quality monitors also available UL listed for Class I and II/Div 2 applications, and as general purpose displays TWINSBURG, OH - Pepperl+Fuchs VisuNet IND Series Industrial Flat Panel LCD Monitors have received Zone 2 certification for use in hazardous environments. These high quality monitors are fully configurable to suit specific application needs in extreme environments and/or for...
Read More »
PRT-Based Sensors provide distance measurement up to 8 m.
Measuring 88 x 26 x 54 mm, VDM28 Series, based on Pulse Ranging Technology, provides distance measurements from 200 mm to 8 m with 1 mm resolution, less than 5 mm repeatable accuracy, and response time as fast as 10 ms, regardless of target surface. Sensors utilize visible red laser light source and are immune to cross-talk. Operating at 10-30 Vdc with max load current of 100 mA, units feature...
Read More »Design Software validates Fieldbus and Profibus PA segments.
With Segment Checker v1.20, users can intuitively check operational parameters to validate fieldbus segment architecture. Users can also display, archive, and print entire design, import field devices from library, or create new devices with Device Editor feature. Additionally, projects can be exported in graphic format for use in different media. Version 1.20 includes FieldConnex fieldbus...
Read More »
Microwave Motion Sensors operate automatic pedestrian doors.
RMS Series sensors actuate sliding, swinging, folding, and revolving pedestrian doors when approaching traffic is detected. RMS-M-NA sensor features single SPST relay output operating in NO or NC, while model RMS-D-RC-NA includes remote control with LCD display for programming and adjustments. RMS-D-NA sensor has turtle-mode capability to detect extremely slow motion. They can be mounted as high...
Read More »
Loop Converter bridges HART and analog signals.
Acting as transmitter power supply and HART monitor, HART Loop Converter (HLC) lets users access digital information from HART-enabled field devices and make it available to analog process control as 4-20 mA signals. Up to 3 HART signals can be monitored simultaneously and are provided as independent analog signals, or HLC can provide one signal via 3 analog channels to send to different systems....
Read More »ecom Wins German Design Award 2020
Explosion-proof smartphone Smart-Ex 02 and remote speaker microphone RSM-Ex 01 awarded by German Design Council Assamstadt, Germany, November 22, 2019: The Pepperl+Fuchs brand ecom receives the German Design Award 2020 for outstanding design quality in the category Computer and Communication for two products. The prestigious award goes to the new explosion-proof smartphone Smart-Ex 02 as well...
Read More »Pepperl+Fuchs Celebrates the Opening of IoT-Enabled Distribution Center in Katy, Texas
The fully automated warehouse is one of the most modern in North America. Katy, Texas (October 2019)—Pepperl+Fuchs, a pioneer and innovator in industrial sensor and explosion protection technologies, recently celebrated the grand opening of its new United States Distribution Center (UDC) located in Katy, Texas. An over $25 million investment that spans an area of 110,000 square feet, the...
Read More »
Stationary Barcode Imager reads common 1D and 2D codes.
Rated to IP65 and usable over 32 to 122Ã-
Read More »
Remote I/O Gateway accelerates data transfer via Modbus TCP.
Comprised of Ethernet communication gateway and backplane, ETHERNET Remote I/O bridges field instruments and Modbus TCP-based Ethernet with data transfer rates to 100 Mbps. Field signals can have intrinsically safe connection for Div 1/Zone 0 applications, and up to 80 analog or 184 discrete signals can be controlled through one gateway. While high transfer frequencies require LWL connections for...
Read More »
Fieldbus-Based Power Supply suits explosive hazardous locations.
Dynamic Arc Recognition and Termination System (DART) is power supply and control system for fieldbus installations in intrinsic safety environments. Feeding power of 8-50 W, product detects change in current resulting from electrical fault where explosive spark is possible and immediately switches off power. Power is shut off in microseconds, robbing spark of energy needed to ignite hazardous...
Read More »
Stack Light Lamps offer alternative to stack light LEDs.
Intended for application where LED-lit stack lights are too costly to warrant use, VAZ-LAMP series stack lights provide visual Warning or Ready status indication. Products, available in blue, green, clear, yellow, and red, are lit by incandescent light bulb. If bulb burns out, it can be replaced without having to replace entire stack light. Stack lights are compatible up to 4 lights high with...
Read More »
AS-Interface Gateways support standard and safety networks.
Available in single master, dual master, and dual master with safety monitor versions, ENX Series supports Modbus/TCP and Ethernet/IP protocols for seamless communication with standard and safety networks. All models include integrated duplicate address, noise, and ground fault detection. With ENX gateways, 992 I/O are handled asynchronous to Ethernet traffic. Units scan every AS-i node in 150...
Read More »
Pepperl+Fuchs Industrial Flat Panel Monitors Now Zone 2 Certified for Use in Hazardous Environments
High quality monitors also available UL listed for Class I and II/Div 2 applications, and as general purpose displays TWINSBURG, OH - Pepperl+Fuchs VisuNet IND Series Industrial Flat Panel LCD Monitors have received Zone 2 certification for use in hazardous environments. These high quality monitors are fully configurable to suit specific application needs in extreme environments and/or for...
Read More »
PRT-Based Sensors provide distance measurement up to 8 m.
Measuring 88 x 26 x 54 mm, VDM28 Series, based on Pulse Ranging Technology, provides distance measurements from 200 mm to 8 m with 1 mm resolution, less than 5 mm repeatable accuracy, and response time as fast as 10 ms, regardless of target surface. Sensors utilize visible red laser light source and are immune to cross-talk. Operating at 10-30 Vdc with max load current of 100 mA, units feature...
Read More »Design Software validates Fieldbus and Profibus PA segments.
With Segment Checker v1.20, users can intuitively check operational parameters to validate fieldbus segment architecture. Users can also display, archive, and print entire design, import field devices from library, or create new devices with Device Editor feature. Additionally, projects can be exported in graphic format for use in different media. Version 1.20 includes FieldConnex fieldbus...
Read More »